manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. ICM Controls
  6. •
  7. Thermostat
  8. •
  9. ICM Controls FS1500L General instructions

ICM Controls FS1500L General instructions

Caution
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing
the fuse or switching the appropriate circuit breaker to the OFF position before
removing the existing thermostat.
IMPORTANT: Thermostat installation must conform to local and national building and electrical
codes and ordinances.
Important Safety Information
WARNING!
:
Always turn off power at the main power supply before installing, cleaning,
or removing thermostat.
• Thisthermostatisfor24VACapplicationsonly;donotuseonvoltagesover30VAC
• Donotshortacrossterminalsofgasvalveorsystemcontroltotestoperation;thiswilldamageyour
thermostatandvoidyourwarranty
• Allwiringmustconformtolocalandnationalelectricalandbuildingcodes
• Usethisthermostatonlyasdescribedinthismanual
General Description
TheSimpleComfort®FS1500L/FS1500VLthermostatisadigital,mercury-free,non-programmable,
electronicthermostat.
•Compatiblewithsingle-stageheatingsystems
•Compatibleasamasterthermostatinzonedsystemapplications
•System Customization:Choosethreeavailabletemperaturedifferentialsettings
To Remove Existing Thermostat
1.Turnoffpowertotheheatingsystembyremovingthefuseorswitchingofftheappropriatecircuit
breaker.
2.Removecoverofoldthermostat.Thisshouldexposethewires.
3.Labeltheexistingwireswiththeenclosedwirelabelsbeforeremovingwires.
4.Afterlabelingwires,removewiresfromwireterminals.
5.Removeexistingthermostatbasefromwall.
6.Refertothefollowingsectionsforinstructionsonhowtoinstallthisthermostat.
Replacing Wiring Labels
Replacetheoldlabelswiththe
enclosednewlabels. Old New Type
F,G G Fancontrolrelay
H,W,4 W Heatingcontrol
M,4,RH,RS,R R Transformer,hotside
N/A S1,S2 Optionalremotesensor
Specifications
Electrical rating: •Millivoltto30VAC/VDC
 •DCPower:3.0VDC(2“AA”alkalinebatteriesincluded)
 •1ampmaximumperterminal,2ampmaximumtotalload
Temperature control range: 35°Fto75°FAccuracy:±1°F
Back Light:Notavailableonsomemodels
Differential Rage:1°Fto3°F
System congurations:1-stageheat,gas,oil,electric
Terminations:R,W,G,S1,S2
Installation, Operation & Application Guide
For more information on our complete range of American-made
products – plus wiring diagrams, troubleshooting tips and more,
visit us at www.icmcontrols.com
Manual Changeover
Non-Programmable
Battery
• Controls Single Stage Heating Systems
• Millivolt and Hydronic (water or steam) System Compatible
• Compatible with Gas and Electric Systems
• Backlit Display
• Mercury-Free,
Environmentally Safe
FS1500L/FS1500VL
GARAGE THERMOSTAT
Non-Programmable Electronic Thermostat
Parts Diagram (Horizontal model shown)
Battery
Compartment
Electric/GasJumper
HighTemperatureSwitch
ModeSwitch FanSwitch
Thermistor
Note: Mount thermostat about ve feet above the oor. Do not mount the thermostat on an outside
wall, in direct sunlight, behind a door, or in an area affected by a vent or duct.
1. Turnoffpowertotheheatingsystembyremovingthefuseorswitchingofftheappropriatecircuit
breaker.
2. MovetheFan Auto/OnswitchintoAuto position.
3. Toremovecover,insertandtwistacoinorscrewdriverintheslotsonthesidesofthethermostat.
4. Putthermostatbaseagainstthewallwhereyouplantomountit(Besurewireswillfeedthrough
thewireopeninginthebaseofthethermostat).
5. Marktheplacementofthemountingholes.
6. Setthermostatbaseandcoverawayfromworkingarea.
7. Usinga3/16”drillbit,drillholesintheplacesyouhavemarkedformounting.
8. Useahammertotapsuppliedanchorsinmountingholes.
9. Alignthermostatbasewithmountingholesandfeedthecontrolwiresthroughwireopening.
10.Usesuppliedscrewstomountthermostatbasetowall.
11. Insertstripped,labeledwiresinmatchingwireterminals.See“WiringDiagrams”sectionofthis
manual.
CAUTION!
: Be sure exposed portion of wires does not touch other wires.
12.Tightenscrewsonterminalblock.Gentlytugwiretobesureofproperconnection.Doublecheck
thateachwireisconnectedtotheproperterminal.
13.SettheGAS/ELECjumpertoElectricorGas/Oil
14.Inserttwofresh“AA”alkalinebatteriesintothermostat,orientedinthedirectionshownonthe
batterycompartment.
15.Replacecoveronthermostatbysnappingitinplace.
16.Turnonpowertothesystematthemainservicepanel.
To Install Thermostat
IfyourLCDisblankordisplayingLO BAT,thebatteriesarenotinstalledorneedtobechanged.We
suggestyouchangethebatteriesatleastonceayear,orwhenevertheLO BATwarningdisplays.
Note: After installing new batteries, you have to reset the room temperature setting and the
differential setting.
1.MovetheOff/HeatswitchintotheOffposition.
2.MovetheFan Auto/OnswitchintoAuto position.
3.Removethecover,andinstallthetwo“AA”alkalinebatteries.Properbatteryinstallationis
important!Makesurethepositiveendsofthebatteriesmatchthepositiveterminalsinthebattery
compartment.
Ifthedisplayison,thebatteriesareinstalledproperly.
Installing and Changing Batteries
Package Contents/Tools Required
Package includes: SimpleComfort®FS1500L/FS1500VLthermostatonbase,thermostat
cover,wiringlabels,screwsandwallanchors,(2)“AA”alkalinebatteries,and
Installation,OperationandApplicationGuide.
Tools required for installation:Drillwith3/16”bit,hammer,screwdriver.
1. Removecoverfromremotesensorhousing.
2. Selectanappropriatelocationformountingtheremotesensor.
3. Mountremotesensorunitusinghardwareprovided.
4. Installtwoconductorshieldedwiresbetweenremotesensorandthermostat.Shieldedwiremust
beused.Do notrunremotesensorwireinconduitwithotherwires.
 •Wire 1shouldrunbetweentheS1terminalonthethermostatandtheS1terminalontheremote
sensor
 •Wire 2shouldrunbetweentheS2terminalonthethermostatandtheS2terminalontheremote
sensor
 •ConnecttheshieldingofthewiretotheS2terminalonthethermostat
5. Disablethemainsensoronthethermostatby
cuttingitfromthecircuitboard.
S1 S2 W G R
CutThermistor
fromcircuit
board
Remote Sensor Installation (Optional) Setting the Temperature Differential
Thedefaulttemperaturedifferentialis1°.Whenyourroomtemperaturevariesby1°F,thethermostat
turnsonyoursystem.Ifyounoticeyoursystemturningonandofftoofrequently,increasethe
temperaturedifferential.
1.Resetthethermostatbyremovingbatteriesfor10secondsandthenreinstallthem.
2.Fortherst10secondsofoperation,thetemperaturedifferentialisdisplayed.
3.Pressthedownorupbuttontoselectdesiredsetting.
Starting the Thermostat
1.MovetheFan Auto/OnswitchintotheAutoposition.
2.MovetheOff/HeatswitchintotheHeatposition.
A Quick Test
Donotshortjumperacrossterminalsonthegasvalveoratthesystemcontroltotestinstallation.
Action: SettheOff/HeatswitchtoHeat;pressthe
up
buttonuntilthesettemperatureis5°Fabovethe
roomtemperature.
Result:Heatingsystemandfanshouldturnon;theremaybeatimedelaydependingonyour
system.
Action:
Pressthedownbutton
untilthesettemperatureisbelowtheroomtemperature.
Result:Theheatingsystemshouldturnoff;theremaybeafandelay.
Action: SettheFan Auto/OnswitchtoOn.
Result:Theblowerfanshouldturnon.
Action: SettheFan Auto/OnswitchtoAuto.
Result:Theblowerfanshouldturnoff.
Iftheabovetest was successful,youhaveaproperinstallation.
Iftheabovetest was unsuccessful,doublecheckthatthewiresaresecurelyconnectedandare
connectedtotheproperterminals.Consultthetroubleshootingsectionbelow.
Troubleshooting
Symptom Remedy
Thesystemisnotturningon Checkbatteries;displayisblankwhenbatteriesarenotpresentor
aredead.
LCDisblank,ordisplaying
LO BAT
Replacebatteries,ormakesuretheexistingonesareproperly
installed.
Thermostatisnotproperly
controllingthefan
CheckthattheGASELECjumperpositionmatchesyoursystem
(gasorelectric).
Thermostatturnsonandoff
toofrequently
Adjusttemperaturedifferential
(see“SettingtheTemperatureDifferential”).
ONE-YEAR LIMITED WARRANTY
TheSellerwarrantsitsproductsagainstdefectsinmaterialorworkmanshipforaperiodofone(1)year
fromthedateofmanufacture.TheliabilityoftheSellerislimited,atitsoption,torepair,replaceorissuea
non-casecreditforthepurchasepricesofthegoodswhichareprovidedtobedefective.Thewarrantyand
remediessetforthhereindonotapplytoanygoodsorpartsthereofwhichhavebeensubjectedtomisuse
includinganyuseorapplicationinviolationoftheSeller’sinstructions,neglect,tampering,improperstorage,
incorrectinstallationorservicingnotperformedbytheSeller.InordertopermittheSellertoproperly
administerthewarranty,theBuyershall:1)NotifytheSellerpromptlyofanyclaim,submittingdatecode
informationoranyotherpertinentdataasrequestedbytheSeller.2)PermittheSellertoinspectandtest
theproductclaimedtobedefective.ItemsclaimedtobedefectiveandaredeterminedbySellertobenon-
defectivearesubjecttoa$30.00perhourinspectionfee.ThiswarrantyconstitutestheSeller’ssoleliability
hereunderandisinlieuofanyotherwarrantyexpressed,impliedorstatutory.Unlessotherwisestated
inwriting,Sellermakesnowarrantythatthegoodsdepictedordescribedhereinaretforanyparticular
purpose.
LIAF013
Patent No. 424,953
7313 William Barry Blvd., North Syracuse, NY 13212
(Toll Free)800-365-5525(Phone)315-233-5266(Fax)315-233-5276
www.icmcontrols.com
Setting the Setpoint Temperature
1.PlaceOff/HeatswitchintheHeatposition.
2.Pressthedownorupbuttonasingletimetoseethecurrent temperaturesetting.
3.Pressthedownorupbuttonuntilthedesired temperaturesetpointdisplays.
4.Thenewtemperaturesetpointisautomaticallysavedinmemory.After5seconds,thedisplay
returnstoshowingthecurrentroomtemperature.
FS1500L/VL Wiring Diagrams
Heating Only
3-Wire,
Single Transformer
2-Wire,
Single Transformer or Millivolt
Zone Valve/Damper Motor System
3-Wire, Zone Valve/Damper Motor System
2-Wire, Zone Valve/Damper Motor System
Note: Differential temperature may need to be increased for zone/damper systems.

This manual suits for next models

1

Other ICM Controls Thermostat manuals

ICM Controls SC2211 General instructions

ICM Controls

ICM Controls SC2211 General instructions

ICM Controls SC 1800 General instructions

ICM Controls

ICM Controls SC 1800 General instructions

ICM Controls SC700LV User manual

ICM Controls

ICM Controls SC700LV User manual

ICM Controls SC 5011 General instructions

ICM Controls

ICM Controls SC 5011 General instructions

ICM Controls SC1600L User manual

ICM Controls

ICM Controls SC1600L User manual

ICM Controls SC1001 General instructions

ICM Controls

ICM Controls SC1001 General instructions

ICM Controls SC4011 General instructions

ICM Controls

ICM Controls SC4011 General instructions

ICM Controls SC 2210 General instructions

ICM Controls

ICM Controls SC 2210 General instructions

ICM Controls SC 2311 General instructions

ICM Controls

ICM Controls SC 2311 General instructions

ICM Controls SC1800L User manual

ICM Controls

ICM Controls SC1800L User manual

ICM Controls SC 2000 Instruction manual

ICM Controls

ICM Controls SC 2000 Instruction manual

ICM Controls SC 3001 General instructions

ICM Controls

ICM Controls SC 3001 General instructions

ICM Controls SC900V General instructions

ICM Controls

ICM Controls SC900V General instructions

ICM Controls Single Comfort SC2010L User manual

ICM Controls

ICM Controls Single Comfort SC2010L User manual

ICM Controls SC4011 User manual

ICM Controls

ICM Controls SC4011 User manual

ICM Controls SC 3006 General instructions

ICM Controls

ICM Controls SC 3006 General instructions

ICM Controls SC3000L General instructions

ICM Controls

ICM Controls SC3000L General instructions

ICM Controls SC1901L General instructions

ICM Controls

ICM Controls SC1901L General instructions

ICM Controls Simple Comfort SC3211L User manual

ICM Controls

ICM Controls Simple Comfort SC3211L User manual

ICM Controls SC 4211 General instructions

ICM Controls

ICM Controls SC 4211 General instructions

ICM Controls SC 5811 User manual

ICM Controls

ICM Controls SC 5811 User manual

ICM Controls SC4812 User manual

ICM Controls

ICM Controls SC4812 User manual

ICM Controls SC3211L General instructions

ICM Controls

ICM Controls SC3211L General instructions

ICM Controls SC 2000 General instructions

ICM Controls

ICM Controls SC 2000 General instructions

Popular Thermostat manuals by other brands

Viega 15117 Product instructions

Viega

Viega 15117 Product instructions

Siemens RDG100 Series Documentation

Siemens

Siemens RDG100 Series Documentation

Pego Expert DIN NANO 4CK quick start guide

Pego

Pego Expert DIN NANO 4CK quick start guide

Tekmar 509 User brochure

Tekmar

Tekmar 509 User brochure

Honeywell TH8320R1003 Product data

Honeywell

Honeywell TH8320R1003 Product data

Honeywell HE0118 Setup guide

Honeywell

Honeywell HE0118 Setup guide

Hunter 44428 Owner's Manual & Installation Instructions

Hunter

Hunter 44428 Owner's Manual & Installation Instructions

tado° RU01 Technical documentation

tado°

tado° RU01 Technical documentation

Young Regulator T-720 Series installation manual

Young Regulator

Young Regulator T-720 Series installation manual

Beretta SUN 1 N instruction manual

Beretta

Beretta SUN 1 N instruction manual

Heatmiser TM4-TS instruction manual

Heatmiser

Heatmiser TM4-TS instruction manual

Braeburn 2100 user manual

Braeburn

Braeburn 2100 user manual

Bosch 8-733-944-325 Installation & operation

Bosch

Bosch 8-733-944-325 Installation & operation

VDH ALFA 31 DP user manual

VDH

VDH ALFA 31 DP user manual

RCS TZ43 Installation and operation manual

RCS

RCS TZ43 Installation and operation manual

EVENTHERM TH-4-20 manual

EVENTHERM

EVENTHERM TH-4-20 manual

Aube Technologies TH108PLUS specification

Aube Technologies

Aube Technologies TH108PLUS specification

Saswell SAS810FHL-7 manual

Saswell

Saswell SAS810FHL-7 manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.