Icon Process Controls truflo Ultraflo UF500 User manual

Ultraflo UF500 Instruction Manual

Content
Product Components.............................................................1
Installation and Connection...................................................2
Panel Function......................................................................3
Powering On.........................................................................3
Keypad Functions..................................................................3
Display Descriptions...............................................................4
Dimensions...........................................................................8

Components
If you have any questions please contact your representative as
soon as possible.
Display
Cable
Base Bracket
Upper Bracket
Instruction manual
Coupling Agent
Instruction Manual
F5
1
Notice
Thank you for choosing UF 500 Series Flow Meter.
This instruction manual contains the important using and
operation information of the flow meter. Please read
carefully prior to operation.

2
Installation and Connection
Brown DC +
Bl ack DC - / 4-20mA
Gray 4-20mA+
Bl ue RS485 A
Whi te RS485 B
Step1: Make sure no dirt, paint, or other
stains on the surface of the tube. Then
position on the underside of the pipe.
Step3: Slowly remove the protective
cover off the sensor.
Step5: Connect the M cable.
Step2: Align the upper bracket to the
pipe position. Using the mounting screws
connect the upper and the lower brackets
together. Ensure that the parts are snug,
but DO NOT over-tighten.
Step4: Position the display over the
upper bracket and connect using the
mounting screws. DO NOT over-tighten.

3
Panel
Powering n
the
self-diagnosis program
Mounting screw
M16
OLED display screen
Signal Quality (SQ value)
Q value Signal Quality. indicates the level of the
signal detected. Q value is indicated by numbers from 0 99
represents that no signal is being detected while 99 represents the
GPM
Gal
0
F
ma ximum signal strength
Keypad functions
Follow these guide lines when using the Flow meter keypad:
Press to enter the Programming Mode or to return to the previo us
menu during programming.
Press to scroll up or down
Press
Press to select digits (0-9)
Press to confirm selection.
to move to the next digit
Mounting screw
Keypad
Model

4
escriptions
Display Menu
ower on display Velocit Total
Display signal quality. Time, velocity, flow rate and net totalize.
Press to display Flow Rate/Net Total. Press to return
to previous menu.
Press to display Flow Rate/ Velocit y/Net Total. Press
to return to previous menu.
Press to display Run time/Daily Total /Monthly Total /Yearly Total
Press to return to previous menu.
Display Run time, Date, Month and Year Net Total
Setup Menu
Press to display Setup menu.
The following options are available (using the or buttons)
1. Pipe parameter
2. System settin g
3. Calibration
4. Output settin g
Run Time
Date : 19-06-22
Time : 12 : 30
Velocity : 1.035 ft/s
Flow Total Net : 723.58 Gal
Signal Quality : 88
Time : 12:30:29
: 3.325 GPM
NET : 723.58 Gal
Signal Quality : 88
Time : 12:30:29
Vel : 1.035 ft/s
Flow Rate : 3.325 GPM
Flow total Net : 723.58 GAL
Gal
Gal
Gal

5
Setup Menu – Pipe Parameter
Press to display:
, Select 0.Pipe parameter, then
The following options are available (using the or buttons)
1. Outer diameter
2. Wall thickness
3. Material: Press to choose between PVC, Carbon steel, Steel,
Copper pipe.
3.Fluid type: Press or to choose between Water,Sea Water,Oil...etc.
Setup Menu – System setting
Press , Select 1.System setting, then to displa y:
The following options are available (using the or buttons)
0. System Unit: Press or to choose between Metric, English.
1. Flow Rate Unit: Press or to choose between m3/h, LPM, GPM.
2. Total Unit: Press
or to choose between m3, L, GAL.
3.Totalizer Reset: Press then press the or arrow to select
'YES' or 'NO'. If 'YES' is selected, parameters will be reset .
4. Time Set
Generally, it is unnecessary to modify date
time as the system is provided with a highly
reliable perpetual calendar chip.
5.System Lock
Once the system is locked, any modifications to the system are
prohibit ed, but the parameter is readable. “Unlock” using your
designated password.
- 5 -
or

6
6.System INFO
System INFO: Display serial number (SN) of the meter. This SN is the
only one assigned to each flow meter.
Set zero: Press ; reset “Zero Point” which was set by the user.
Manual Totalizer: The manual totalizer is a separate totalizer.
Press to start, and press to stop. It is used for isolated flow
measurement and calculation.
Setup Menu – Calibration
Press to display:
, Select 2.Calibration, and the n
and to display 4mA set point.
Use and to set 4mA.
After 4mA is set, press to move to your 20mA set point.
Once 20mA is set, press to move to next screen.
2.Set Zero: Press ; reset “Zero Point” which was set by the user.
3.Low flow Cut: Flow rate below the low flow cutoff valu e.
ft
ft
Press
1. Scale factor
Refers to the ratio between the “actual value” and “reading value”. For
example, when the measurement is 2.00, and it is indicated at 1.98 on the
instrument, the scale factor reading is 2/1.98.
This means that the best scale factor constant is 1.01.
2. Calibrate 4 & 20mA
Press

7
Setup Menu – Output Setting
Press ,
Select 3.Output setting, and then display:
0.RS 485 setup
Set the Current Loop output valu e according to the flow value
4mA, and 20mA. The flow unit is GPM
2.Alarm Value(Optional)
Enter the low alarm valu e; (if the measured flow is lower than
the low alarm value), the alarm relay will be activated.
Enter the high alarm value; (if the measured flow is higher
that the high alarm value), the alarm relay will be activated.
If the flow is below the cut-off the flow indication on the display will be
zero. (This function can prevent the flow meter from reading flow after
a pump is shut down but there is still liquid movement in the pipe, which
would result in a flow total error.)
Generally, 0.03ft/s is recommended to enter as the low flow cut off
point. The low flow cutoff value has no relation to the
results once the velocity increases over the low flow cutoff value.
This window is used to set RS 485 serial port . It must match the
equipment's connected parameters .
First select baud rate: 2400,4800,9600,19200 are selectable Then
select : None . Data length :8 Stop bit is fixed length . Factory
default value for serial port parameter is ''9600,8,None,1''
1.4-20mA Range

8
Dimensions
106
A
B
D
C106
42
40
UF-20
UF-25
UF-32
UF-40
UF-50
UF-63
A
(mm)
B
(mm)
C
(mm)
D(mm)
Model min max
25
25
28.5
29.5
36
41
1.5/Φ25
58
58
58
68
78
91
1.5/Φ32
1.5/Φ38
4.5/Φ28
4.5/Φ35
8.5/Φ45
8
15
18.5
24
27
32
1.5/Φ20
1.5/Φ48
1.5/Φ58
8/Φ23
8.5/Φ54
.5/Φ64
[email protected] | [email protected] | PH: 905.469-9283
For Additional Support Please Contact US