ICP DAS USA PCI-D64HU User manual

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
1
PCI-D64HU
User’s Manual
Warranty
All products manufactured by ICP DAS are warranted against defective materials for a
period of one year from the date of delivery to the original purchaser.
Warning
ICP DAS assume no liability for damages consequent to the use of this product. ICP
DAS reserves the right to change this manual at any time without notice. The information
furnished by ICP DAS is believed to be accurate and reliable. However, no responsibility is
assumed by ICP DAS for its use, nor for any infringements of patents or other rights of third
parties resulting from its use.
Copyright
Copyright 2009 by ICP DAS. All rights are reserved.
Trademark
The names used for identification only may be registered trademarks of their respective
companies.

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
2
Table of Contents
1. Introduction.......................................................................................................................3
1.1. General Description.............................................................................................................3
1.2. Features................................................................................................................................. 4
1.3. Block Diagram...................................................................................................................... 5
1.4. Specifications........................................................................................................................ 6
1.5. Product Check List..............................................................................................................7
2. Hardware Configuration...................................................................................................8
2.1. Board Layout........................................................................................................................ 8
2.2. Switch Setting....................................................................................................................... 9
2.3. Pin Assignment................................................................................................................... 10
2.4. Operation Theory................................................................................................................11
2.5. Timing Characteristic........................................................................................................ 14

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
3
1. Introduction
1.1. General Description
The PCI-D64HU card provides 40 MB/s High-Speed 32-CH Digital Input and
32-CH Digital Output.PCI-D64HU is a high-speed digital I/O card consisting of 32
digital input channels and 32 digital output channels. High-performance designs
make this card perfect for high-speed data transfer and pattern generation
applications.
The PCI-D64HU has the Card ID switch on board. Users can set Card ID on a
board and recognize the board by the ID via software when using two or more
PCI-D64HU cards in one computer.
The PCI-D64HU performs high-speed data transfer by bus-mastering DMA via
32-bit PCI bus. The maximum data transfer rate can be up to 40 MB per second.
Several digital I/O transfer modes are supported, such as direct programmed I/O
control, timer pacer control, external clock mode and handshaking mode. It is a
reliable and cost-effective connection interface that works on your computer system
to control high-speed peripherals.

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
4
1.2. Features
The following is a list of general features for the PCI-D64HU. Check section 1.5
for more details.
Support 32-bit, 33 MHz Universal PCI bus
32-CH 5V TTL Digital Inputs and 32-CH 5V TTL Digital Outputs
2-CH Bus Mastering Scatter/Gather DMA
Data Transfer Rate up to 40 MB/s for Each Channel
Support 4 Data Transfer Modes
Direct Program Control Mode
Internal Timer Pacer Mode
External Clock Mode (DI Only)
Handshaking Mode
On Board 1 k/2 k DWORD FIFO for DI/DO Respectively
DO FIFO Support Ring Buffer Mode -- No Bus Loading in Repetitive Pattern
Card ID function
1.3. Generation Application
Programmable Input Digital Filter for All Input Signals Including Handshaking
and Trigger Signals

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
5
1.4. Block Diagram

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
6
1.5. Specifications
Model Name PCI-D64HU
Digital Input
Channels 32
Compatibility 5 V/TTL
Input Voltage Logic 0: 0.8 V max.
Logic 1: 2.0 V min.
Handshaking Signals I_REQ input , I_ACK output , I_TRG input
Digital Output
Channels 32
Compatibility 5 V/TTL
Output Voltage Logic 0: 0.55 V max.
Logic 1: 2.0 V min.
Output Capability Sink: 64 mA @ 0.55 V
Source: -32 mA @ 2.0 V
Handshaking Signals O_REQ output, O_ACK input, O_TRG output
Transfer Speed 40 MB/sec for DI and DO simultaneously (max.)
Programmable Digital Filter
Applicable Signals All input signals (including 32 DI signals, I_REQ, I_TRG and O_ACK)
Max. removable noise width (1 ~ 127) x 25 ns
Programmable Pulse Extender
Applicable Signals O_REQ
Pulse width (2 ~ 256) x 25 ns
Timer/Counter
Channels 3
Resolution 16-bit
Input Frequency 2.5 ~ 20 MHz
Timer 0 Clock source of DI
Timer 1 Clock source of DO
Timer 2 Base clock of Timer 0 and Timer 1
Interrupt
Sources O_ACK, I_REQ, Timer 0, Timer 1 and Timer 2
On Board FIFO
DI / DO 1 k DWORD (32-bit)
2 k DWORD (32-bit)
Size in Ring Buffer Mode 2 ~ 2 k DWORD (32-bit), DO only
General
Bus Type Universal PCI, 32-bit, 33 MHz
Card ID Yes (4-bit)
I/O Connector Female DB37 x 1
40-pin Box header x 1
Dimensions (L x W x D) 120 mm x 105 mm x 22 mm
Power Consumption 200 mA @ +5 V typical (output no load)
Operating Temperature 0 ~ 60 °C
Storage Temperature -20 ~ 70 °C
Humidity 5 ~ 85% RH, non-condensing

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
7
1.6. Product Check List
In addition to this manual, the package includes the following items:
One PCI-D64HU card
One ICP-DAS software CD-ROM
One Quick Start Guide
It is recommended to read the Quick Start Guide first. The following important
information will be given in the Quick Start Guide:
1. Where you can find the software driver & utility
2. How to install software & utility
3. Location of the diagnostic program
1.7. Ordering Information
Ordering Information:
PCI-D64HU: 40 MB/s High-speed 32-CH DI and 32-CH DO Universal PCI DIO
Card (RoHS). Includes one CA-4037W cable and two CA-4002 D-Sub
connectors
Accessories:
CA-3710: DB-37 Male-Male D-sub cable 1M (45º)
CA-3710DM: DB-37 Male-Male D-sub cable 1M (180º)
DN-37: DIN-Rail Mounting 37-pin Connector (Pitch=5.08mm)
DN-37-381: DIN-Rail Mounting 37-pin Connector (Pitch=3.81mm)
DB-37: Directly connect signal to D-Sub 37-pin connector
Attention!
If any of these items are missing or damaged, please contact your local field
agent. Save the shipping materials and carton in case you want to ship or store the
product in the future.

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
8
2. Hardware Configuration
2.1. Board Layout
Item Description
CON1 I/O connector (37-pin D-Sub female)
CON2 I/O connector (40-pin Box Header)
SW1 Card ID switch
JP1 Factory reserved

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
9
2.2. Card ID Switch Setting
SW1: Card ID Switch
The SW1 switch is used to set the card ID. The value is from 0 to 15. Please refer to
table below for details.
1 2 3 4
ON Switch Setting
(On = 1)Card ID 1234
0(Default) 0000
1 1000
2 0100
3 1100
4 0010
5 1010
6 0110
7 1110
8 0001
9 1001
10 0101
11 1101
12 0011
13 1011
14 0111
15 1111
Default

PCI-D64HU User’s Manual (Ver.1.0, Dec/2009)
10
2.3. Pin Assignment
The PCI-D64HU has one 37-pin D-Sub connector (CON1) and one 40-pin pin header (CON2). Please
refer figure below for the pin assignment of CON1 and CON2
Signal Name Description Direction
DIx Digital input channel x Input
DOx Digital output channel x Output
GND Ground of all signals Power
+5V +5V power output (Max. 400 mA per pin) Power
I_TRG Trigger input to start DI sampling Input
I_REQ Request input for DI handshaking Input
I_ACK Acknowledge output for DI handshaking Output
O_TRG Trigger output controlled by software Output
O_REQ Request output for DO handshaking Output
O_ACK Acknowledge input for DO handshaking Input
DI2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
27
28
29
30
20
31
32
33
34
35
36
37
DI3
DO2
DO1
DO
0
DI1
DI0
DI6
DI7
DI5
DI4
DO
5
DO
6
DO4
DO3
DO1
0
DO8
DO
7
DI8
DO9 DI9
DI13
DI12
DI14
I_REQ
DI15
C
O
N
1
DI10
DI11
I_TRG
DO1
5
+5V
GND I_ACK
DO11
DO12
DO13
DO14
DI18
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
4
6
8
10
12
14
16
18
20
22
2
24
26
28
30
32
34
36
DI19
DO18
DO17
DO16 DI17 DI16
DI22
DI23
DI21
DI20
DO21
DO22
DO20
DO19
DO26
DO24
DO23 D
I
2
4
DO25 D
I
2
5
DI29
D
I
28
DI30
O_REQ
DI31
C
O
N
2
DI26
DI27
O_TRG
DO31 +5VGND O_ACK
DO27
DO28
DO29
DO30
39
38
40
N.C.
N.C. N.C.