ICP DAS USA SG-3013 User manual

Ver1.33，2016/05/26，～1～
SG-3013 User’s Manual
Isolated RTD Input Module
Introduction
The SG-3013 is a RTD input signal conditioning module to transform RTD input to voltage
or current output. SG-3013 uses a microprocessor-based transducer, which integrating two
high resolution ADCs and an MCU, to acquire the RTD signal. The supported RTD types
are Pt100 , Pt1000 , Ni 120 , Cu100 ,and Cu1000.
The SG-3013 supports 1000 VDC isolation. The power supply that drives the module`s input
and output circuitry is internally isolated.
It’s easy to mount the SG-3013 on a standard DIN rail and can operate in environment with
wide temperature range.
Specifications
Signal Input:
Input Type: Pt100 α=0.00385 / Pt100 α=0.003916 / Ni 120 / Pt1000 α=0.00385
Input Connections:2 / 3 / 4 wires
RTD Type and Temperature Ranges:
Voltage output:
Unipolar: 0~5 VDC, 0~10 VDC
Output impedance: < 50 Ω
Current output:
Current: 0~20 mA, 4~20 mA
Current load resistor:0~500 Ω(Source)
General
Three-way isolation: 1000 VDC
Accuracy: ±0.1 % of full range
Operation temperature range:-25 °C～75 °C
Storage temperature range:-30 °C～85 °C
Weight: 94 gram
Supply Voltage
Input Range: 10~30 VDC
Consumption: < 1.2 W
RTD Type αTemperature range(℃)
Pt100 0.00385 -200~600
Pt100 0.003916 -200~600
Pt1000 0.00385 -200~600
Ni 120 -80~300
Cu 100 at 0 °C α= 0.00421 -20~150
Cu 100 at 25 °C α= 0.00427 0~200
Cu 1000 at 0 °C α= 0.00421 -20~150

Ver1.33，2016/05/26，～2～
Configuration
The terminal wiring for the SG-3013 is shown in Figure A. The SG-3013 uses a power input
range of 10~30 VDC.
Table 1 and table 2 show the switch positions used to configure the input and output range.
The I/O configuration switches are located inside the module. And can be accessed by
removing the DIN-rail bracket covers by sliding them in the direction shown in Figure B.
Switch Setting
SW1 Dip switch
N.O 1 2 3 4 5 6 7 8
Function 0
21 22 23 24
25
26 2+/-
SW2 Dip switch
N.O 1 2 3 4 5 6 7 8
Function
RTD Type Set Open RTD Current
output
Voltage
output
0
21 22 23 24 20V/0mA
10V/20mA
0-20mA
4-20mA
10V
5V
Table 1: Offset setting (SW1)
◆offset: 0.1 ℃
Table 2: In/Output type setting (SW2)

Ver1.33，2016/05/26，～3～
RTD Type Setting table：
Open RTD：
SW2-6 determines output range of SG-3013 when RTD wiring open.
Current Output：
SW2-7 determines current output range.
Voltage Output：
SW2-8 determines Voltage output range.
No Switch
Temperature Range (℃)RTD Type
1 0x00 00000 -200~200
Platinum 100,α= 0.00385
2 0x01 10000 -200~600
3 0x02 01000 -100~100
4 0x03 11000 -100~0
5 0x04 00100 -100~200
6 0x05 10100 -50~50
7 0x06 01100 -50~150
8 0x07 11100 0~100
9 0x08 00010 0~200
10 0x09 10010 0~600
11 0X0A 01010 -200~200
Platinum 100,α= 0.003916
12 0X0B 11010 -200~600
13 0X0C 00110 -100~100
14 0X0D 10110 -100~0
15 0X0E 01110 -100~200
16 0X0F 11110 -50~50
17 0x10 00001 -50~150
18 0x11 10001 0~100
19 0x12 01001 0~200
20 0x13 11001 0~600
21 0x14 00101 -200 ~ 600 Platinum 1000,α= 0.00385
22 0x15 10101 -80 ~ 100
Nickel 120
23 0x16 01101 0 ~ 100
24 0x17 11101 0~300
25 0x18 00011 -80~300
26 0x19 10011 -20 ~ 150 Cu 100 at 0℃,α=0.00421
27 0x1A 01011 0 ~ 200 Cu 100 at 25℃,α=0.00427
28 0X1B 11011 -20 ~ 150 Cu 1000 at 0℃,α=0.00421

Ver1.33，2016/05/26，～4～
Label：
SW1 Dip switch
N.O 1 2 3 4 5 6 7 8
On/Off □□□□□□□ □
Input Pt100, α=0.00385, -200℃~+200℃
SW2 Dip switch
N.O 1 2 3 4 5 6 7 8
On/Off □ □ □ □□□ ■ □
Output 4~20 mA or 0~10 V
Factory default setting：

Ver1.33，2016/05/26，～5～
Wiring Diagram

Ver1.33，2016/05/26，～6～
Block Diagram
Dimensions
Technical Service:
Please E-mail your problem description to serv[email protected] if you have any questions.
More detail information: http://www.icpdas.com/