ICP DAS USA I-7019R User manual

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
I-7019R
8 Channel Universal Analog /
Thermocouple Input Module
Quick Start Guide
Product Website:
http://www.icpdas-usa.com/i_7019r.html
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
I-7019R provides cost-effective protection and conditioning for a wide
range of valuable industrial control signals and systems. I-7019R provides
4KV of ESD protection. The individual channels are configurable; the user
selects the type and range remotely by issuing commands from the host.
Fewer modules may be used for different applications. The user may
mount the modules on a DIN rail, panel or wall. Modules have a screw-
terminal block to connect to the signals. I-7019R comes with FREE EZ
Data Logger Software.
2. Terminal Assignment

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
4. I-7019R Jumper setting

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
5. Default Settings
Default settings for the I-7019 series modules are:
▫Module address: 01
▫Analog input type:
Type 08, -10V to 10V
▫Baud Rate: 9600 bps
▫Checksum disabled
▫Engineering unit format
6. Configuration
To install the module, follow the steps below:
1. Connect the analog input.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
7
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
8
7. For I-7000 modules, DCON utility pro terminal can send command to the module.
See user manual Sections 2 for details command.
Configure the module: sending the %AANNTTCCFF command. See user manual
Section 2 for detail commands. To configure the I-7017Z, I-7018Z and I-7019 series, the
$AA7CiRrr command must also be sent.
Read data from the input channels: send either the #AA or #AAN command to the
module.

I-7019R 8 Channel Universal Analog / Thermocouple Input Module - QuickStart (Feb/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
9
8. If user doesn’t know the command, user can select Address and ID, it will show
some refer commands as below. User can select necessary command to test or debug
modules.