ICP DAS USA PISO-DA2U User manual

PISO-DA2U Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The package includes the following items:
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
The PISO-DA2 series driver supports Windows 98/NT/2K and 32-bit XP/
2003/ Vista/7/8. Recommended to install this driver for have been used
PISO-DA2 series board of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-da2/manual/quickstar
t/classic/
For PISO-DA2U
What’s in the shipping package?
Installing Windows Driver
English/ Jun. 2013/ Version 1.2
Software Utility CD
(V5.2 or later)
Quick Start Guide
(This Document)
PISO-DA2U
Two CA-PC09M
D-Sub Connectors

PISO-DA2U Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
For more detailed jumper information, please refer to manual section 2.2
Configuration of D/A Output signal. (CD:\NAPDOS\PCI\PISO-DA2\manual\)
Jumper Setting
1
2
1. CN1: D/A converter channel-1
2. CN2: D/A converter channel-2
3. JP1/JP2/JP5/JP9: Bipolar or
Unipolar setting.
4. JP4/JP8: -5 V or -10 V internal
reference voltages setting.
5. JP3/JP7: 0~20 mA or 4-20 mA
current loop setting.
6. JP6/JP10: External or internal
reference voltage setting.
7. SW1: Card ID setting.
JP2
JP1
SW1
JP9
JP5
JP4
JP8
JP7
JP3
JP10
JP6

PISO-DA2U Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Please make sure that all jumpers are kept in default setting before self-test.
JP6/JP10: External or internal reference voltage setting.
channel
Internal
External
channel
Internal
External
CN1
(Default)
CN2
(Default)
JP4/JP8: -5 V or -10 V Internal reference voltages setting.
channel
-5 V
-10 V
channel
-5 V
- 10 V
CN1
(Default)
CN2
(Default)
JP5/JP9: Bipolar or Unipolar setting.
channel
Unipolar
Bipolar
channel
Unipolar
Bipolar
CN1
(Default)
CN2
(Default)
JP3/JP7: 0~20 mA or 4~20 mA current loop setting.
channel
4-20 mA
0-20 mA
channel
4-20 mA
0-20 mA
CN1
(Default)
CN2
(Default)

PISO-DA2U Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI slot.
Step 4: Carefully insert your I/O card into the PCI slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
CN1 and CN2 D/A Connector (Male DB9).
Pin Assignments
Installing Hardware on PC

PISO-DA2U Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
1. Prepare for device:
DN-09-2 (optional) Wiring terminal board.
Digital Multi-Meter.
2. Connect a DN-09-2 to the CN1.
3. Connect the positive probe (+) of
Multi-meter to CN1.V_OUT (Pin 01).
4. Connect the negative probe (-) of
Multi-meter to CN1.GND (Pin 04).
Self-Test
CN1
DN-09-2

PISO-DA2U Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
5. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be
placed in the default path after
completing installation.
Default Path: C:\ICPDAS\UniDAQ\Driver\
6. Get Analog Output function test result.
Double-Click
1
Confirm the PSIO-DA2
series card had
successfully installed to
PC. It start s from 0.
2
Click this button
to start test.
3
Click “Analog Output”item.
Click this button.
Select the “Port 0”
Select the
“Unipolar 0~5V”
Type the voltage value
4
5
6
7
8

PISO-DA2U Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
PISO-DA2U Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-da2.html
CA-0915 and DN-09-2 page (optional):
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
http://www.icpdas.com/products/DAQ/screw_terminal/dn_09_2.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information
PASS
2.499
Check the value on multi-meter,
they should be identical to the values
set in program.
The value read on meter may be a little difference from the DA value
because of the resolution limit of meter or the measurement error.
9