ICP FIR-ULV600-DVR User manual

FIR-ULV600-DVRUserManual Page:1/56
FIR-ULV600-DVR
User Manual
Version 1.0
POS+DVR
December 2005

FIR-ULV600-DVRUserManual Page:2/56
Copyright Notice
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the
part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
Trademarks
FIR-ULV600-DVR is registered trademarks of ICP Electronics Inc.; IBM PC is a
registered trademark of International Business Machines Corporation. INTEL is a
registered trademark of INTEL Corporation. AMI is registered trademarks of
American Megatrends Inc. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks of
their respective companies.
Support
Any questions regarding the content of this manual or related issues can be e-mailed
to us directly at: [email protected]

FIR-ULV600-DVRUserManual Page:3/56
Table of Contents
Chapter1 Introduction...............................................................................................5
1.1 Specification ...............................................................................................5
1.2 Package Contents........................................................................................7
Chapter2 Installation.................................................................................................8
2.1 Block Diagram & Board Layout.................................................................8
2.1.1 Block Diagram.................................................................................8
2.1.2 Board Layout ...................................................................................9
2.1.3 Board Dimension...........................................................................10
2.2 Unpacking Precautions .............................................................................10
2.3 System Memory DRAM...........................................................................11
2.4 Clear CMOS Setup ...................................................................................11
2.5 TFT LCD Setting......................................................................................11
2.6 COM4 Voltage Selection ..........................................................................12
2.7 COM4 Mode Selection.............................................................................12
2.8 COM2 RI Function Setting.......................................................................12
2.9 COM1 RI Function Setting.......................................................................13
2.10 Keyboard Data & Clock by pass.............................................................13
2.11 COM5 & 6 RI (CN11 pin8 & 18) Function Setting................................13
Chapter3 Connection ..............................................................................................14
3.1 Compact Flash Storage Card Socket (CF1)..............................................14
3.2 Serial Port Connector (COM1, COM2, COM4, COM5 & COM6)..........15
3.3 Parallel Port Connector (LTP1).................................................................16
3.4 Primary IDE Connector (IDE1)................................................................17
3.5 VGA Connector (VGA1 & VGA2) ..........................................................18
3.6 CPU & system Fan Connector (J4 & J5)..................................................19
3.7 USB Connector (USB1 & USB2).............................................................19
3.8 LVDS Connector (LVDS1 & LVDS2)......................................................19
3.9 Box Header Connector (CN7) ..................................................................20
3.10 Keyboard/Mouse Connector (KB_MS1 & CN10) .................................21
3.11 Power Button (PS_ON1).........................................................................21
3.12 Power LED (LED1)................................................................................22
3.13 Power SW/LED Connector (CN4)..........................................................22
3.14 Digital I/O with RJ-11 Connector (CN2)................................................22
3.15 Power Connector (CN5 & CN8).............................................................23
3.16 LCD Back Light Connector (CN6 & CN9)............................................23

FIR-ULV600-DVRUserManual Page:4/56
3.17 Audio Connector.....................................................................................24
3.17.1 Speaker Out Phone Jack Connector (J6)......................................24
3.17.2 MIC In Phone Jack Connector (J7)..............................................24
3.17.3 Speaker Out Pin Header Connector (CN3)..................................24
Chapter4 BIOS Setup..............................................................................................25
4.1 Setup Menu...............................................................................................25
4.2 Setup Submenu: Main...............................................................................26
4.3 Setup Submenu: Advanced.......................................................................27
4.3.1 CPU Configuration ........................................................................28
4.3.2 IDE Configuration (Compatible Mode).........................................29
4.3.2.1 Primary IDE Master (if attached Hard Disk)......................30
4.3.3 Super IO Configuration..................................................................32
4.3.4 Hardware Health Configuration (Manual Mode) ..........................35
4.3.4.1 Hardware Health Configuration (Thermal Cruise Mode)...36
4.3.4.2 Hardware Health Configuration (Speed Cruise Mode) ......36
4.3.5 ACPI Configuration.......................................................................38
4.3.6 USB Configuration ........................................................................39
4.4 Setup submenu: Boot................................................................................40
4.4.1 Boot Settings Configuration ..........................................................41
4.4.2 Boot Device Priority......................................................................43
4.4.3 Hard Disk Drives ...........................................................................44
4.4.4 Removable Devices .......................................................................44
4.4.5 CD / DVD Drives...........................................................................45
4.5 Setup submenu: Security...........................................................................46
4.6 Setup submenu: Chipset............................................................................47
4.6.1 North Bridge Chipset Configuration..............................................48
4.6.2 South Bridge Chipset Configuration..............................................50
4.7 Setup submenu: Power..............................................................................51
4.8 Setup submenu: Exit.................................................................................52
Appendix A Address Mapping................................................................................54
A.1 I/O Address Map......................................................................................54
A.2 1st MB Memory Address Map.................................................................54
A.3 IRQ Mapping Chart .................................................................................55
A.4 DMA Channel Assignment ......................................................................55
Appendix B Digital I/O...........................................................................................56

FIR-ULV600-DVRUserManual Page:5/56
Chapter1 Introduction
1.1 Specification
1. Form Factor
Form
Dimension: W 188 x D 122 mm
2. Processor Compatibility
Processor
CPU Type: Intel Celeron-M Processors
Max. Speed: Celeron-M 600MHz
FSB: 400 MHz
Package: Micro-FCBGA
L2 Cache: 0KB
CPU Process: 90nm
3. Main Chipset
North Bridge
Controller Hub: i82852GM GMCH
FSB: 400 MHz
VGA:
Dual independent pipe support: Concurrent, Simultaneous
◆VGA port
◆LVDS panel support
Memory: DDR 200/266 MHz up to 1GB
Package: 732-pin Micro-FCBGA (37.5 x 37.5 mm)
Hub Interface (HI): 66 MHz (266-MB/s)
South Bridge
Controller Hub: i82801DB ICH4
PCI Compliant: PCI 2.2
Package: 421-pin BGA (31x31 mm)
PCI Bus: Supports up to six master devices on PCI
Other Feature:
◆6 USB 2.0 ports, 480MB/s
◆IDE up to ATA 100 mode
◆AC'97 2.3 CODEC support

FIR-ULV600-DVRUserManual Page:6/56
◆Power Management
◆LPC interface to SIO and Flash BIOS
◆ SMBus 2.0
Firmware Hub: 4Mb Flash
4. Additional Chipset
LAN
Chipset: Realtek RTL8100BL
IEEE Compliant: IEEE 802.3u 100Base-T and IEEE 802.3x Full Duplex Flow
Control
Audio
Codec: AC'97 2.3 CODECALC202A
Rear panel output: Line-out, MIC-in
Hardware Monitor
Chipset: LPC I/O W83627EHF for onboard alarm
Super I/O
Chipset: Winbond 83627EHF
Fan: CPU Fan / System Fan
Monitor Voltage: TBD
Serial I/O
Chipset: FINTEK F81216D
COM 3, 4, 5, 6
Power Management
ACPI Support: ACPI 1.0b and 2.0
APM Support: APM Rev 1.2 compliant power management
Others:
◆SMRAM space remapping to A0000h (128-kB)
◆Support extended SMRAM space above 256-MB, additional 1-MB TSEG
from top of memory, cacheable (cache ability controlled by CPU)
◆Support Suspend to System Memory, Suspend to Disk and Soft Off
◆Enhanced Intel Speed Step technology support
◆Optimized Clock Gating for 3D and Display Engines
◆ On-Die Thermal Sensor
Wakeup on LAN: TBD
Bootup Device
IDE device: Yes
Compact Flash: Yes
USB device: Yes

FIR-ULV600-DVRUserManual Page:7/56
ACPI 2.0
1.2 Package Contents
Before any installation, please check if the following materials are included in the
package:
zOne FIR-ULV600-DVR all-in-one single board computer
zOne compact disk for utility and drivers
If any of these items are missing or damaged, contact your distributor or sales
representative immediately.

Chapter2 Installation
This chapter gives instructions about how to set up the FIR-ULV600-DVR hardware,
including directions of setting jumpers and connecting peripherals, switches and
indicators. Before installation, please pay attention to the unpacking precautions on
the following page for safety.
2.1 Block Diagram & Board Layout
2.1.1 Block Diagram
Intel
Celeron M
Intel
852GM
Intel
ICH4
PC-104 PLUS LAN0
RTL 8100BL
Transformer
LAN
RJ45
DDR-SODIMM 0
200 / 266 MHz
DAC
LVDS
CRT PORT
LCD CONN
HDD
SUP I/O
W83627HF
LPT PORT
COM2 PORT
COM1 PORT
FAN CONN
BIOS
28F040T
LPC I/O
F81216D
LPC I/O
ITE8706 DIO
COM3 PORT
COM4 PORT
COM5 PORT
COM6 PORT
LPC
AC97 CODEC
AUDIO
CONN
AC97
USB PORT 0
USB PORT 1
USB PORT 2
USB PORT 3
USB PORT 4
USB PORT 5
USB 2.0
PCI BUS, 3.3V
RS232
RS232
RS232
RS232
FIR-ULV600-DVRUserManual Page:8/56

2.1.2 Board Layout
LVDS2
LVDS1
JP10 VGA2
VGA1
CN6
CN9
USB1 KB/MS
CN10
Button LED
CN4
J5
JP2
CN5
J4
CN8
Power
J7 J6
MIC SPK
USB2 COM4 COM2 COM1
CN2
DIO
CF
JP7
Power
DDR DIMM Socket
LAN
J3
CN1
IDE1
LPT1
COM5
COM6
JP6 JP5
CN7 JP8 JP9
COM3+USB
JP11 CN3
CN11
+
FIR-ULV600-DVRUserManual Page:9/56

2.1.3 Board Dimension
zFIR-ULV-600’s Dimensions (Unit: mm)
2.2 Unpacking Precautions
Some components of FIR-ULV600-DVR SBC are very sensitive to static electric
charges and can be damaged by a sudden rush of power. To protect it from unintended
damage, be sure to note these precautions:
1. Ground yourself to remove any static charge before touching the
FIR-ULV600-DVR SBC. You can do it by using a grounded wrist strap at all
times or by frequently touching any conducting materials that is connected to the
ground.
2. Handle FIR-ULV600-DVR SBC by its edges. Don’t touch IC chips, leads or
circuitry if not necessary.
3. Do not plug any connector or jumper while the power is on.
FIR-ULV600-DVRUserManual Page:10/56

FIR-ULV600-DVRUserManual Page:11/56
2.3 System Memory DRAM
There are one 200-pin DDR SO-DIMM sockets to accept 2.5V non-buffered SDRAM.
The max Memory size is 1GB.
2.4 Clear CMOS Setup
To clear the CMOS Setup (for example, if you have forgotten the password, you
should clear the CMOS and then re-set the password), you have to close the JP2 (2-3)
for about 3 seconds, and then open it. This will put the system back to normal
operation mode.
zJP2: Clear CMOS Setup
JP2
PIN STATE DESCRIPTION
Short 1-2
(default)*
Keep CMOS Setup
(Normal Operation)
Short 2-3 Clear CMOS Setup
*Note: All shaded rows in the tables of this manual are the default settings.
2.5 TFT LCD Setting
zJP7/JP10: TFT LCD Voltage (5V / 3V) Setting
JP7 for LVDS1, JP10 for LVDS2
JP7 & JP10
PIN STATE DESCRIPTION
Short 1–2 3V TFT LCD
Short 2–3 5V TFT LCD

FIR-ULV600-DVRUserManual Page:12/56
2.6 COM4 Voltage Selection
zJP8: COM4 Voltage Selection
JP8
PIN STATE DESCRIPTION
Short 1-2 +12V
Short 2-3 +5V
2.7 COM4 Mode Selection
zJP9: COM4 Mode Selection
JP9
PIN STATE DESCRIPTION
Short 1-2 CTS RTS short
Short 3-5 +12V/+5V output
Short 4-6 Ground output
2.8 COM2 RI Function Setting
zJP5: COM2 RI Function Setting
JP5
PIN STATE DESCRIPTION
Short 1-2 RI is +5 Voltage output
Short 3-4 RI function
Short 5-6 RI is +12 Voltage output

FIR-ULV600-DVRUserManual Page:13/56
2.9 COM1 RI Function Setting
zJP6: COM1 RI Function Setting
JP6
PIN STATE DESCRIPTION
Short 1-2 RI is +5 Voltage output
Short 3-4 RI function
Short 5-6 RI is +12 Voltage output
2.10 Keyboard Data & Clock by pass
zCN10: Keyboard Data & Clock by pass
CN10
PIN STATE DESCRIPTION
Short 2-3 Clock by pass
Short 4-5 Data by pass
2.11 COM5 & 6 RI (CN11 pin8 & 18) Function Setting
zJP11: COM5 & 6 RI Function Setting
JP11
PIN STATE DESCRIPTION
Short 1-2 RI is +12 Voltage output
Short 3-4 RI is +5 Voltage output

FIR-ULV600-DVRUserManual Page:14/56
Chapter3 Connection
This chapter describes how to connect peripherals, switches and indicators to the
FIR-ULV600-DVR board.
zTable of Connectors
LEBAL FUNCTION
LVDS1 & 2 LVDS LCD Panel connectors
VGA1 & 2 VGA connectors
LAN LAN RJ45 connector
USB1 & 2 USB dual port connectors
COM1, 2, 4, 5 & 6 Serial port connectors
KB_MS1 Keyboard & Mouse connector
J4 & 5 Fan connectors
J6 Speaker out phone jack connector
J7 MIC in phone jack connector
CN3 Speaker out pin header connector
LPT1 Parallel port connector
IDE1 Ultra ATA100 Primary IDE connectors
CF1 Compact Flash Storage Card Type II connecto
r
PS_ON1 Power on Switch
LED1 Power LED
CN1 PC/104 Plus connector
CN2 Digital I/O with RJ-11 connector
CN4 Power SW/LED connector
CN5 Power output connector
CN6 & 9 LCD back light connectors
CN7 Multi-function connector
CN8 +12V DC power connector
CN10 Internal Keyboard connector
CN11 Serial port connectors
3.1 Compact Flash Storage Card Socket (CF1)

zCompact Flash Storage Card Socket
FIR-ULV600-DVRUserManual Page:15/56
CF1
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GROUND 26 PULL DOWN
2 D3 27 D11
3 D4 28 D12
4 D5 29 D13
5 D6 30 D14
6 D7 31 D15
7 CS1# 32 CS3#
8 N/C 33 N/C
9 GROUND 34 IOR#
10 N/C 35 IOW#
11 N/C 36 VCC
12 N/C 37 IRQ15
13 VCC 38 VCC
14 N/C 39 MASTER/SLAVE
15 N/C 40 N/C
16 N/C 41 RESET#
17 N/C 42 IORDY
18 A2 43 DREQ
19 A1 44 DACK#
20 A0 45 ACTIVE#
21 D0 46 PDIAG#
22 D1 47 D8
23 D2 48 D9
24 N/C 49 D10
25 PULL DOWN 50 GROUND
3.2 Serial Port Connector (COM1, COM2, COM4,
COM5 & COM6)
zCOM1 & COM2: D-SUB Serial Port Connectors

FIR-ULV600-DVRUserManual Page:16/56
COM1 & COM2
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 (DCD) 6 (DSR)
2 (RXD) 7 (RTS)
3 (TXD) 8 (CTS)
4 (DTR) 9 (RI or 5V or 12V)
5 GROUND
10 N/C
zCOM4: RJ45 Serial Port Connector
COM4
PIN NO. DRSCRIPTION PIN NO. DESCRIPTION
1 +12/+5V 5 DTR
2 +12/+5V or CTS 6 DSR
3 GROUND 7 TXD
4 GROUND or RTS 8 RXD
zCOM5 & COM6: Serial Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 (DCD) 2 (DSR)
3 (RXD) 4 (RTS)
5 (TXD) 6 (CTS)
7 (DTR) 8 +5V or +12V
COM5
9 GROUND 10 GROUND
11 (DCD) 12 (DSR)
13 (RXD) 14 (RTS)
15 (TXD) 16 (CTS)
17 (DTR) 18 +5V or +12V
COM6
19 GROUND 20 GROUND
3.3 Parallel Port Connector (LTP1)

zLPT1: Parallel Port Connector
FIR-ULV600-DVRUserManual Page:17/56
LTP1
P
IN NO
.
DESCRIPTION
P
IN NO.
.
DESCRIPTION
1 STROBE# 14 AUTO FORM FEED #
2 DATA 0 15 ERROR#
3 DATA 1 16 INITIALIZE
4 DATA 2 17 PRINTER SELECT IN
#
5 DATA 3 18 GROUND
6 DATA 4 19 GROUND
7 DATA 5 20 GROUND
8 DATA 6 21 GROUND
9 DATA 7 22 GROUND
10 ACKNOWLEDGE 23 GROUND
11 BUSY 24 GROUND
12 PAPER EMPTY 25 GROUND
13 PRINTER SELEC
T
26 N/C
3.4 Primary IDE Connector (IDE1)
zIDE1: Primary IDE Connector
IDE1
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RESET# 2 GROUND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GROUND 20 N/C

21 DRQ 22 GROUND
23 IOW# 24 GROUND
25 IOR# 26 GROUND
27 CHRDY 28 REV. PULL LOW
29 DACK 30 GROUND-DEFAULT
31 INTERRUPT 32 N/C
33 SA1 34 PD66 SELECT
35 SA0 36 SA2
37 HDC CS0# 38 HDC CS1#
39 HDD ACTIVE# 40 GROUND
41 VCC 42 VCC
43 GROUND 44 N/C
3.5 VGA Connector (VGA1 & VGA2)
zVGA1: 15-pin Female Connector
VGA1
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RED 2 GREEN
3 BLUE 4 NC
5 GROUND 6 GROUND
7 GROUND 8 GROUND
9 VCC / NC 10 GROUND
11 NC 12 DDC DAT
13 HSYNC 14 VSYNC
15 DDCCLK
zVGA2: 10-pin Box Header Connector
VGA2
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RED 6 DDCCLK
2 GREEN 7 DDCDAT
FIR-ULV600-DVRUserManual Page:18/56

3 BLUE 8 GROUND
4 HSYNC 8 GROUND
5 VSYNC 10 GROUND
3.6 CPU & system Fan Connector (J4 & J5)
zJ4: CPU Fan Connector
zJ5: system Fan Connector
FIR-ULV600-DVRUserManual Page:19/56
J4 & J5
PIN NO. DESCRIPTION
1 Rotation Signal
2 +12V
3 Ground
3.7 USB Connector (USB1 & USB2)
zUSB1 & USB2: 2 ports USB Connectors
USB1 & USB2
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 USB Power 5 USB Power
2 DATA4- 6 DATA5-
3 DATA4+ 7 DATA5+
4 GROUND 8 GROUND
3.8 LVDS Connector (LVDS1 & LVDS2)
zLVDS1 & LVDS2: LVDS Connectors

LVDS1 & LVDS2
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GROUND 2 GROUND
3 CH1 DATA3+ 4 CH1 DATA3-
5 CH1 CLK+ 6 CH1 CLK-
7 CH1 DATA2+ 8 CH1 DATA2-
9 CH1 DATA1+ 10 CH1 DATA1-
11 CH1 DATA0+ 12 CH1 DATA0-
13 GROUND 14 GROUND
15 CH2 DATA3+ 4 CH2 DATA3-
17 CH2 CLK+ 6 CH2 CLK-
19 CH2 DATA2+ 8 CH2 DATA2-
21 CH2 DATA1+ 10 CH2 DATA1-
23 CH2 DATA0+ 12 CH2 DATA0-
25 GROUND 26 GROUND
27 LCD power 28 LCD power
29 LCD power 30 LCD power
3.9 Box Header Connector (CN7)
zCN7: COM3 & USB Box Header Connector
CN7
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 VCC
3 USB1- 4
USB0-
5 USB1+ 6 USB0+
7 GND 8 GND
9 DTR
10 CTS
11 RTS 12 TXD
13 RXD 14 DSR
FIR-ULV600-DVRUserManual Page:20/56