ICP PHAD60N1K1 User manual

• Safety Labeling and Rules •Ductwork Connections
•Installation Requirements •Wiring
•Location/Clearances • Start-Up Procedures
• Air Distribution •Maintenance
•Economizer Accessory • Hoisting/Rigging
80-10-41
I RESIDENTIAL SINGLE PHASE WITH DIRECT DRIVE BLOWER II
I-
Printed in U.S.A. 518 01 1001 00 7/97

Table Of Contents
1. Safety Labeling and Signal Words ... 1
Danger, Warning and Caution ............... 1
Signal Words .............................. 1
Signal Words in Manuals ................ 1
Product Labeling ........................... 1
Danger Label .......................... 1
Warning Label ......................... 1
Caution Label ......................... 1
2. Unit Dimensions .................... 2
3. Safe Installation Requirements ...... 4
4. Locating The Unit ................... 4
Access Panels ............................. 4
Clearances ................................ 4
Minimum Clearances to Combustible
Construction .......................... 5
Installation ................................. 5
Ground Level Installation ................ 5
Rooftop Installation ..................... 6
Hoisting ................................... 6
Downflow Conversion ....................... 7
Condensate Drain .......................... 8
5. Electrical Wiring .................... 9
Low Voltage Wiring ......................... 9
Low Voltage Wiring With
Economizer Option ..................... 9
Thermostat ................................ 9
Unit Without Economizer ............... 10
Unit With Economizer ................. 10
Ground Connections ....................... 10
Line Voltage Wiring ........................ 10
Converting 230V Units to 208V .............. 10
Field Installed Equipment .............. 10
Final Electrical Check .................. 10-11
6. Air Distribution System ............. 12
Ductwork ................................. 12
Ductwork Insulation ................... 12
Ductwork Connections ................. 12
Filters .................................... 12
7. Economizer Accessory ............. 13
Theory of Operation ........................ 13
Sequence of Operation ..................... 14
Cooling Mode ............................. 14
Heating Mode ............................. 14
8. Start-up Procedures ............... 15
Circulating Air Blower ...................... 15
Determining Blower Speed ............. 15
Speed Taps ............................... 15
Cooling, Heating and Auxiliary
Electric Strip Heat (Heat Pump) ......... 15
Check Before Starting ...................... 15
Circulating Air Blower .................. 15
Sequence of Operation ............ 16-17
9. Operation ......................... 18
Features ............................. 18
Scroll Anti-Cycle Timer ..................... 18
Thermal Expansion Valves .................. 18
Loss of Charge Pressure Switch ............. 18
Defrost Control Time Interval Adjustment ...... 18
Cooling .............................. 18
Turning The Unit Off ....................... 18
Thermostat Fan Switch Operation ............ 19
Adjusting Room Temperatures ............... 19
10. Maintenance ..................... 19
Air Filters, Condenser Coil and
Condensate Drain Maintenance .............. 19
Refrigeration Access Ports .................. 19
Annual Maintenance and Inspection .......... 20
Condenser Fan Motor ................. 20
Blower Motor Access ....................... 20
Method 1 and Method 2 ................ 20
Blower Motor Removal Using Method 1 .. 21
Blower Motor and Blower Housing
Removal Using Method 2 .............. 21
Blower Wire Color Identification .............. 21
Circulating Air Blower .................. 21
11. Rigging Instructions .............. 22

I Single Package Heat Pumps Installation Instructions I
1.SafetyLabeling andSignalWords
Danger,Warning and Caution
The signal wordsDANGER, WARNING and CAUTION are
used to identify levels of hazard seriousness. The signal
word DANGER is only used on product labels to signify an
immediate hazard. The signal words WARNING and CAU-
TION will be used on product labels and throughout this
manual and other manuals that may apply to the product.
Danger Label
White lettering on a black background except the word
DANGER which is white with a red background.
Signal Words
DANGER - Immediate hazards which WILL result in se-
vere personal injury or death.
WARNING - Hazards or unsafe practices which COULD
result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which COULD
result in minor personal injury or product or property dam-
age.
Warning Label
White lettering on a black background except the word
WARNING which is black with an orange background.
Signal Words in Manuals
The signal word WARNING is used throughout this manual
in the following manner:
The signal word CAUTION is used throughout this manual
in the following manner:
CAUTION
Product Labeling
Signal words are used in combination with colors and/or
pictures on product labels. Following are examples of prod-
uct labels with explanations of the colors used.
Caution Label
White lettering on a black background except the word
CAUTION which is black with a yellow background.
12J

_Installation Instructions Single Package Heat Pumps I
2. UnitDimensions
MODELS:
2- 3 TON
DIM INCHES MILLMETERS
A 32 1/2" 826
B 47 3/8" / 203
C 47 38" / 203
D 3 1'8" 79
E /1 //8" 283
F 12" 306
G /4 1_4" 363
H /4 I/4" 363
I /2" 306
J4" 102
K N/A N/A
L 4 /'4" /08
M 43/8" ///
N /4 //2" 368
P /2 /'4" 3/1
Q /2 1'8" 308
R E4 /4" 363
S /2 /'4" 3E8
LOW VOLTAGE
1/2" CONDUIT
ELECTRIC HEAT POWER
1", 1-1/2", 2" CONDUIT
UNIT ELECTRICAL POWER
3/4", 1", 1-1/4" CONDUIT UNIT BASE SHOWN SEPARATELY
TO ILLUSTRATE BOTTOM
DUCT OPENINGS
Note: The above dimensions are in inches.
ROOF CURB MODELS:
2- 3 TON
DIM INOHES MILLIMETERS
A 42 34" /086
B 39 34" /0/0
C /8'r 457
D /8" 457
E 3 3_a" 95
F 42 34" / 086
G 39 3_a" /OE0
HE8" 457
K _ 14" 356
"F'"
*Roof curbs are also available in 8" (203mm) and 24" (610mm) heights (K dimension). 8_/_/3

ISingle Package Heat Pumps Installation Instructions
UNIT DIMENSIONS
MODELS:
31/2 -5 TON
DIM INCHES MI L METERS
A 36" 9/4
B 47 38" / 203
C 73" /854
D 4 58" //7
E 15" 38I
F 12" 307
G /8 3/4" 476
H /8 3_4" 476
J E2" 305
J/02
K N/A
L 4 I '4" / 08
M 5 F4" E33
N 12 F4" 311
P E9" 483
Q 15" 381
R 19" 483
S /2 //4" 3/1
• /6 78" 429
I
I
I
LOW VOLTAGE
1/2" CONDUIT
ELECTRIC HEAT POWER
1", 1-1/2", 2" CONDUIT
UNIT ELECTRICAL POWER
3/4", 1", 1-1/4" CONDUIT
,,p.
UNIT BASE SHOWN SEPARATELY
TO _LLUSTRATE BOTTOM
DUCT OPENINGS
Note: Above dimensions are in inches
ROOF CURB MODELS:
31/2 -5 TON
DIM INCHES
A 67 3;4rr
B 64 3;4rr
C 23"
D 23"
E 2 //2"
F 42 3;4"
G 39 3t_4rr
H 23"
I /2"
J 12"
K _ /4"
f_'ILLIMETERS
/721
1645
584
584
64
1086
/010
584
305
305
356
* Roof curbs are also available in 8" (203mm) and 24" (610mm) heights (K dimension). 80 /0 /4

_Installation Instructions Single Package Heat Pumps I
3.SafeInstallationRequirements
Installation or repairs made by unqualified per-
sons can result in hazards to you and others.
Installation MUST conform with local building
codes or, in the absence of local codes, with the
National Electrical Code NFPA70-1990 or current
edition or in Canada CSA C22.1 -Canadian Elec-
trical Code Part 1 or current edition.
The information contained in this manual is in-
tended for use by a qualified service technician
familiar with safety procedures and equipped
with the proper tools and test instruments.
Failure to carefully read and follow all instruc-
tions in this manual can result in unit malfunction,
property damage, personal injury and/or death.
•Seal supply and return air ducts.
• Check to see that filters are installed correctly and
are the proper type and size.
NOTE: It is the personal responsibility and obligation of the
customer to contact a qualified installer to ensure that the
installation is adequate and conforms to governing codes
and ordinances.
4. Locating TheUnit
The unit is designed for outdoor installation only. The unit
may be installed on a concrete slab (or other adequate plat-
form) at ground level, oron a rooftop with an adequate plat-
form or a roof curb. Typical installations are shown in
FIGURE 3 through FIGURE 5.
Access Panels
CAUTION
Unit will NOT operate properly without all access pan-
els in place.
Unit MUST NOT be moved unless all access panels are
in place.
Avoid installations under roof overhangs without guttering.
Water draining from the roof onto the unit could produce ex-
cessive noise, and may cause ice to build up on coil or fan.
See FIGURE 1 on page 5 for a general view of unit and
location of access panels.
Clearances
Roof top installations are acceptable providing the roof will
support the unit and provisions are made for water drain-
age and for the noise or vibration through the structure.
The location MUST allow for minimum clearances and
should not be adjacent to a patio or other area where the
unit's operating sound level might be objectionable. Local
codes MUST be observed.
Minimum clearances, as specified below and in FIGURE 2,
MUST be maintained from adjacent structures to provide
adequate air circulation and room for service personnel.
IJJ

ISingle Package Heat Pumps
While minimum clearances are acceptable for safety rea-
sons, they may not allow adequate air circulation around
the unit for proper operation. Whenever possible, it isdesir-
able to allow additional clearance, especially around the
condenser inlet and discharge openings.
FIGURE1 _Access Panels
Blower Access Panel
I Electrical AccessPanel
Installation Instructions
Minimum Clearances
FIGURE 2(Typical 2 to 3 ton unit shown)
0" (2" (50mm) on 4 & 5 ton units
48" (1220mm) on all units with
economizer
/30"
(762mm)
(914mm) 0"
J30" 30"
(762mm) (762mm)
80-00-01
Installation
Do NOT install the unit in a location that will permit dis-
charged air from the condenser to recirculate to the con-
denser inlet.
CAUTION
Do NOT operate unit in a corrosive atmosphere con-
taining chlorine, fluorine, or any other corrosive chem-
icals.
Minimum Clearances to Combustible Construction
Supply and Return Air Ducts ...................... 0"
Duct Connection Side (no economizer)
...... 0" (2" (50mm) on 4 & 5 ton models)
Duct Connection Side (with economizer) . 48" (1220mm)
Compressor Access Panel Side ......... 30" (762mm)
Blower Access Panel Side .............. 30" (762mm)
Electrical Access Panel Side ............ 30" (762mm)
Clearance between 3 Ft. Overhang
and Top of Unit ............ 30" (762mm)
Combustible Base
(Wood or Class A, B or C
roof covering material) ................. 0"
CAUTION
Unit will NOT operate properly unless it is installed lev-
el front to rear and side to side.
The slope MUST NOT be greater than 1/8" per foot
(lOmm per meter). For side to side leveling, the control
box side MUST always be lower.
GroundLevel Installation
Ground level platform requirements:
The unit MUST be situated to provide safe access for
servicing.
Platform may be made of either concrete or pressure
treated wood and MUST be level and strong enough
to support unit weight.
Position platform separate from building foundation.
Install in well-drained area, with top surface of plat-
form above grade level and above the average winter
snow levels to prevent coil blockage.
Platform MUST be high enough to allow for proper
condensate trap installation and drainage. See Fig-
ure 8 and associated text for more information about
condensate drainage.

_Installation Instructions
See FIGURE 3for illustration of a typical ground level
installation.
Single Package Heat Pumps I
Support for the unit MUST be level and strong
enough to carry unit weight. The support may consist
of a platform or a combination of platform and roof
beams or curb.
Rooftop Installation
Rooftop platform requirements:
The unit MUST be situated to provide safe access for
servicing.
The platform may be constructed of pressure treated
wood and may be covered with Class A, B or C roof
covering.
The unit MUST be installed above average snowfall
levels to prevent coil blockage and to provide ade-
quate drainage for water created in the defrost mode.
The existing roof structure MUST be adequate to
support the weight of the unit orthe roof MUST be re-
inforced.
Check the weight of the unit in relation to the roof
structure and local building codes or ordinances and
reinforce roof structure ifnecessary. See NO TAG on
the back cover of this manual for unit weights and
corner weights.
Platform MUST allow for proper condensate trap
installation and drainage. See FIGURE8 and
associated text for more information about conden-
sate drainage.
See Hoisting section below for hoisting instructions.
See FIGURE 4 and FIGURE 5 for illustrations of typical
rooftop installations.
Hoisting
NOTE: All access panels MUST be secured in place before
hoisting.
The unit should be hoisted with two lifting slings. Attach the
slings to rigging shackles that have been hooked through
holes in the base rail.
Two spreader bars MUST be placed on top of the unit to
protect the unit from damage from the pressure exerted by
the slings. Make sure that all equipment is adequate to
handle the weight of the unit and that the slings will not al-
low the unit to shift.
Refer to FIGURE 19 on the back cover of this manual for
illustrated rigging instructions and weight chart.
FIGURE 3Typical Installation (Ground Level)
2-3 ton unit shown

ISingle Package Heat Pumps
FIGURE 4 /Typical Installation (Roof Curb)
2-3 ton unit shown
1
80-10-16
/
FIGURE 5 | Typical Installation (Pitched Roof)
I31/2-5 ton unit shown
80-30-03
DownflowConversion
Installation Instructions
These units are shipped ready for horizontal operation but
are adaptable to downflow use. To convert to downflow
use, follow these steps:
1. Remove the blockoff plates found in the return air
compartment and the supply air compartment. See
FIGURE 6and FIGURE 7.
NOTE: Blockoff plate in the supply air compartment only
contains one screw. If reinstalling plate, back part of plate
MUST fit into mating dimples of downflow flange. To rein-
stall, slant plate into dimples, then put plate into position
and fasten with screw.
2. Install the removed plates on the horizontal return
and supply air openings.
NOTE: It is the installer's personal responsibility to follow
all local codes and ordinances and instructions contained
herein, as well as instructions included with accessory
items when installing unit. It is the installer's personal re-
sponsibility to locate directions for installation of this unit
and any or all accessories. Manufacturer is NOT responsi-
ble for improper installation practices.
.Position and install appropriate roof curb. (See Page
2 or Page 3 for appropriate curb to use with your
model.)
4. Install unit on roof curb.
FIGURE 6 Blockoff Plate
(Return Air Compartment)

_Installation Instructions
Blockoff Plate Removed
FIGURE 7 (Return Air Compartment)
Condensate Drain
The condensate drain outlet is a 3/4" (19.1mm) threaded
female PVC connection located at the bottom of the unit to
the left ofthe electrical access panel (see FIGURE 8). Con-
densate drain outlet MUST be held with wrench when
installing trap and drain line.
The circulating blower and the condenser fan create a neg-
ative pressure on the condensate drain line that will pre-
vent the condensate from draining properly without a trap.
To combat this negative pressure, a field supplied conden-
sate trap that will allow a standing column of water of at
least 2" (50.8mm) MUST be installed. Top of outlet from
trap MUST be at least 1" (25.4mm) below top of outlet from
unit. Install the trap as near to the unit as possible for
proper drainage.
A3/4" (19.1mm) drain line MUST be installed if required by
local codes or if location of unit requires it. Run the drain
line to an open drain or other suitable disposal point.
Single Package Heat Pumps I
FIGURE 8
3/4" (19.1mm)
Threaded Female
PVC Fitting
ICondensate Drain Information*
Electrical Access Panel
1" (25.4mm)
3/4" (19.1mm)
Drain Line
2" (50.8mm)
* Condensate trap MUST be installed.
80-30-27

I Single Package Heat Pumps Installation Instructions
5. ElectricalWiring
Electrical shock hazard.
Disconnect power at fuse box or service panel
before making any electrical connections.
Unit MUST be grounded to electrical service pan-
el.
Failure to follow this warning can result in prop-
erty damage, personal injury, and/or death.
NOTE: All electrical work MUST conform with the require-
ments of local codes and ordinances and in the United
States with National Electrical Code ANSI/NFPA 70-1990
(or current edition) and in Canada with CSA C22.1 - Cana-
dian Electrical Code Part 1 (or current edition). Provide line
voltage power supply from a separate fused circuit with a
disconnect switch (when required) located within sight of
the unit. Supply voltage, amperage, wire, fuse and discon-
nect switch sizes MUST conform with specifications in the
Parts List and on the unit rating plate.
Wiring MUST be protected from possible mechanical dam-
age and MUST NOT interfere with removal of access pan-
els, filters, etc.
All exposed wiring and connections MUST be made with
weatherproof cable or wire unless installed in conduit.
LowVoltage Wiring
Low voltage connections are made on the low voltage ter-
minal board inside the electrical control compartment (see
FIGURE 11). For access, remove the electrical control ac-
cess panel (see FIGURE 1).
Refer to the Parts List for the connection wiring diagram for
the applicable model and to the instructions included with
the thermostat.
Route low voltage wires through the port located at the bot-
tom left corner of the blower access panel side of the unit.
Route low voltage wires behind unit cornerpost, through
the wire clip provided, and up to the low voltage terminal
board.
NOTE: If an Electric Heat Accessory is installed, see the
Electric Heat Accessory Installation Manual for low voltage
connections. If an economizer is installed, see the follow-
ing section, Low Voltage Wiring With Economizer Option.
LowVoltage Wiring With Economizer Option
Same as the above Low Voltage Wiring section except re-
fer to the connection wiring diagram supplied with the
economizer.
NOTE: The jumper wire on the heat/cool relay must be
disconnected from terminal number 3 and recon-
nected to the economizer wire terminated with an in-
sulated male quick connect. See the
installation/operation manual accompanying the
economizer for more information.
Thermostat
The location of the thermostat has an important effect on
the operation of the unit. FIGURE 9 and FIGURE t 0 show
typical wiring connections for both manual and electronic
thermostats. FOLLOW THE INSTRUCTIONS IN-
CLUDED WITH THE THERMOSTAT FOR CORRECT
LOCATION, MOUNTING AND WIRING
FIGURE 9
[c]
JMechnical Thermostat Low Voltage
Connection Diagram
Mechanical Thermostat Subbase
(White Rodgers: 1F58-34)
(2) 'I
' ' (1)
[G] [R] [O] [Y] [W2] [E]
[c]
Com
[G] [R] [O] [Y1] [Y2]
Fan 24V Rev, Pump Econo.
Valve Heat
Ener Cool
Cool
Jumper Wire
[Wl] [W2]
Aux.
Emer.
Heat
Low Voltage Terminal Board at the Unit.
Thermostat Subbase Notes:
(1) Common [q may be shown as [B] or [X] on other types
of thermostats.
(2) Terminals [W2] and [E] already jumpered at subbase.

_Installation Instructions Single Package Heat Pumps I
ElectronicThermostat Low VoltageFIGURE 10 Connection Diagram
Electronic Thermostat Subbase
y(White Rodgers: 1F92-71 and 1F94-71)
f" " _ 6"'''1
(2) ' (3) '
vI T !
.... (t)I[C] [G] [R] [O1 [YI] [Wl] [W21 [Ell
I
l
I
!
,' Jumper Wire
i
I I I I I I I
[C] [G] [R] [O1 [YI] [Y21 [Wl] ['v_/21
Corn Fan 24V Rev. Pump Econo. Aux.
Valve Heat Emer.
Energ Coo! Heat
Cool
Low Voltage Terminal Board at the Unit.
Thermostat Subbase Notes:
(1) Common [C] may be shown as [B] or IX] on other types
of thermostats.
(2) Jumper subbase terminals [Y1] and [Wt].
(3) Jumper subbase terminals [W2] and [Et].
Connections for line voltage are made on the unit electrical
control plate (see FIGURE 11). For access, remove the
electrical access panel (see FIGURE 1).
Refer to applicable wiring diagram in the Parts List. Com-
plete the line service connections to the contactor 'L' termi-
nals on the electrical control plate. Check all screw
terminals to ensure they are tight.
NOTE: If an Electric Heat Accessory is installed, refer to
the Electric Heat Accessory Installation Manual to deter-
mine line voltage connections. The Electric Heat Accesso-
ry mounts inside the unit. Field supplied line voltage wires
for the Electric Heat Accessory (separate from the field
supplied line voltage wires to the unit) connect to the circuit
breaker(s) in the Electric Heat Accessory.
Converting 230V Unitsto 208V
To convert 230V units to 208V:
1. Turn electric power OFF.
Unit Without Economizer 2. Remove the electrical access panel.
A field supplied two stage heating-single stage cooling
heat pump thermostat is required.
Unit With Economizer
3. Locate the 24V control transformer.
4. Remove wires from the terminal labeled "240V" on
the 24V control transformer and reconnect them to
the 208V terminal of the 24V control transformer.
A field supplied two stage cooling-two stage heating ther-
mostat is recommended for use with an economizer. If a
single stage cooling thermostat is used, the compressor
will not start ifthe economizer can not satisfy the demand
for cooling.
GroundConnections
A ground lug is installed on the control plate for the ground
connection (see FIGURE tt). Use a copper conductor of
the appropriate size from the unit to a grounded connection
in the electrical service panel or to a properly driven and
electrically grounded ground rod. See warning above.
5. Replace the electrical access panel.
Field Installed Equipment
Wiring to be done in the field between the unit and other de-
vices, or between separate devices which are field
installed and located, MUST NOT exceed the temperature
limitations for type T wire and MUST be installed according
to the manufacturer's instructions for the devices.
Final Electrical Check
Une Voltage Wiring
Do NOT complete line voltage connections until unit is per-
manently grounded. All line voltage connections and the
ground connection MUST be made with copper wire.
Make a final wiring check to be sure system is correctly
wired. Inspect field installed wiring and the routing to en-
sure that rubbing or chafing due to vibration will not occur.
NOTE: Wiring MUST be installed so it is protected from
possible mechanical damage.

ISingle Package Heat Pumps Installation Instructions
FIGURE 11 ITypical Wiring Installation
Low Voltage Terminal
Board
Electrical Control Plate
Contactor 'L' Terminals
Ground lug
Carefully route low voltage
wires behind unit corner-
post through wire clip
Field supplied line voltage
wires
Knockout for Electric Heat
Accessory field supplied
line voltage wires

_Installation Instructions Single Package Heat Pumps I
6.Air DistributionSystem
For airflow data (blower performance data, blower speed
tap settings, filter sizes, etc.) see the Parts List.
Ductwork
NOTE: The total heat gain/heat loss from the structure as
expressed in total Btu/hr MUST be calculated by manufac-
turer's method or in accordance with "A.S.H.R.A.E. Guide"
or "Manual J - Load Calculations" published by the Air
Conditioning Contractors of America or in Canada
"H.R.A.I. Residential Heating and Cooling Load Calcula-
tion Manual." The total heat gain calculated should be
equal to or less than the cooling capacity output based
on D.O.E. test procedures, steady state efficiency times in-
put.
Ductwork, supply registers, and return air grilles MUST be
designed and sized to handle the unit's cooling air vol-
ume requirements. If the unit is connected to an existing
system, the ductwork MUST be checked to make sure it is
adequate. Extra runs or larger duct sizes may have to be
installed.
Maximum recommended velocity in trunk ducts is 1000
feet per minute (5.08m/s). Velocity in branches should not
exceed 800 feet per minute (4.06m/s). Refer to the Parts
List for unit air volume requirements and system sizing rec-
ommendations.
Ductwork Connections
The use of flexible, non-combustible connectors be-
tween main trunk ducts and supply and return air plenums
is recommended to minimize vibration transmission.
NOTE: Connect supply and return air plenums to unit in a
manner that will allowthe top ofthe unit to be removed with-
out removing plenums. Plenums MUST be individually
sealed to unit casing. Ducts MUST be terminated inside
structure.
Filters
All return air MUST pass through a filter before entering the
unit. An electronic air cleaner, optional filter racks or other
accessible filter arrangements MUST be installed in the re-
turn air ductwork. Minimum recommended filter areas are
listed in the Parts List and are based on a velocity of 300
ft/min (1.2m/s) for disposable filters and 500 ft/min
(2.54m/s) for washable high velocity filters.
CAUTION
Do NOT operate the unit without all filters in place.
NOTE: Ductwork sizing affects temperature rise and cool-
ing temperature differential. Be sure to properly size duct-
work to the capacity and airflow characteristics of your unit.
Failure to do so can affect limit controls, compressors, mo-
tors, and other components and will lead to premature fail-
ure of components. This will also adversely affect day to
day unit performance.
Refer to unit rating plate for proper Electric Heat Accessory
sizing and see the Temperature Rise Check section in the
Electric Heat Accessory Installation Instructions.
Ductwork Insulation
It is recommended that ductwork installed outdoors have a
minimum of 2" (51mm) of fiberglass insulation and be cov-
ered by a weatherproof vapor barrier that is protected
against damage. Caulking and flashings, or other means
adequate to provide a permanent weather seal, must be
used.
It is recommended that ductwork installed in attics or other
areas exposed to outdoor temperatures have a minimum
of 2" (51mm) fiberglass insulation and have an indoor type
vapor barrier.

ISingle Package Heat Pumps
7. EconomizerAccessory
Installation Instructions
NOTE: For installation and wiring of economizer
see"Low Voltage Wiring of Economizer Option"
(pg.10).
The purpose of an economizer is to:
• Provide cool outdoor air to the conditioned space
during the cooling cycle to minimize the use of com-
pressors.
• Bring outdoor air into the conditioned space to meet
minimum ventilation air requirements whenever the
circulation blower is running.
logic module also controls the compressor staging based
on the thermostat input.
The minimum opening position of the outdoor air dampers
is field adjustable. It is set on the logic module of modulat-
ing economizers or on the actuator motor of three-position
economizers.
The outdoor air enthalpy sensor is factory installed on the
outdoor air dampers. The enthalpy change-over point is
adjustable on the logic module.
Theory of Operation
The economizer has two sets of dampers that are mechan-
ically linked together. The outdoor air dampers regulate the
intake of outdoor air and the return air dampers regulate
the flow of return air (see FIGURE 12). When the outdoor
air dampers modulate open, the linkage causes the return
air dampers to modulate closed. A barometric relief damp-
er is installed in the return air side of the system. It relieves
any positive pressure in the unit created by the economiz-
er.
The economizer is controlled by a logic module which field
connects to the unit controls through a harness plug. The
A mixed air sensor is field installed in the blower inlet. The
mixed air sensor keeps the mixed air above 56°F (13.3°C).
See the economizer installation instructions for the location
of the mixed air sensor.
A positive pressure is created in the building when the out-
door air dampers open and the return dampers close. This
pressure must be vented or the air will not circulate proper-
ly. This is the function of the barometric relief dampers. A
positive pressure forces the passive exhaust dampers to
swing open.
The outdoor air dampers open to the mininum position for
outside air whenever the circulation blower is ON in the
cooling or heating mode.
FIGURE 12 J Typical Downflow Economizer
Outdoor Air Dampers
Mixed Air Sensor
Actuator Motor and
Logic Module
80-50-28b Return Air
Dampers

_Installation Instructions
Sequence of Operation
NOTE: For correct wiring to the low voltage terminal board,
see the connection wiring diagram in the economizer's
documentation and page 10 of this manual.
CoolingMode
When a field supplied two stage thermostat is in the FAN
ON position:
1. The outdoor air dampers will open to the minimum
position with R & G energized.
2. On the thermostat's call for cooling, the thermostat
completes Circuit 1 between thermostat terminals R,
G, O and Y1 for first stage cooling.
If the economizer's outdoor air enthalpy sensor de-
termines that the outdoor air conditions are belowthe
setting for economizer operation, the outdoor air
dampers will modulate open and the return air damp-
ers will modulate closed.
The mixed air sensor at the blower inlet modulates
the economizer dampers to prevent the mixed air
from falling below 56°F (13.3°C). (Mixed air refers to
return air after it combines with outdoor air from the
economizer.) The mixed air sensor modulates the
outdoor air dampers between the full open and mini-
mum outdoor air positions.
If the mixed air is not cold enough to maintain the
conditioned space at the selected temperature, the
thermostat will make ¥2 and call for second stage
cooling by energizing the economizer logic module.
This energizes the Y1 anti-cycle delay timer and
contactor Cl which starts the condenser fan and the
compressor.
If the thermostat is still calling for cooling and the
economizer's outdoor air enthalpy sensor deter-
mines that the outdoor air conditions have risen
above the setting for economizer operation:
Single Package Heat Pumps I
The economizer dampers will close to the mini-
mum position for outdoor air and remain there.
Contactor Cl will remain energized and the com-
pressor will continue to run.
Heating Mode
1.
2.
The outdoor air dampers will open to the minimum
position with R & G energized.
The damper operates at minimum position with R, G
& Y1 energized; in heating operation O is de-ener-
gized. The dampers will not modulate based on the
enthalpy changeover setpoint. Turn to the "D" set-
point and dampers will remain at the minimum posi-
tion setting at high enthalpy conditions for outdoor
air. Turn to the "A" setpoint and the dampers will re-
main at the minimum setting at low enthalpy condi-
tions for outdoor air. This can be checked by putting a
1.2K ohm resistor across terminals O & + and then by
adjusting the setpoint on the enthalpy setpoint
changeover potentiometer. The compressor will run
atthe "D" setting: as the setting is moved to "A" the
compressor will continue to run and the dampers will
remain at minimum position. As the setting is
changed from "A" to "D" the dampers will remain at
minimum position and the compressor will continue
to run.
.
4.
The minimum damper position setting can be set by
adjusting the setting damper position potentiometer.
This can be set so that the dampers will fully close for
a minimum setting if required.
The economizer can be set at a minimum damper
position in heating. The economizer will not modu-
late in the heating mode.
NOTE: For residential applications, it is recommended that
the minimum damper position be set to fully closed position
unless fresh air requirements in the heating mode are nec-
essary.

ISingle Package Heat Pumps Installation Instructions
8.Start-upProcedures
Electrical shock hazard.
Use extreme care during all of the following
checks and procedures.
Make sure electric power is turned OFF as
instructed in appropriate steps.
Failure to follow this warning can result in prop-
erty damage, personal injury, and/or death.
Circulating Air Blower
Determining Blower Speed
1. Turn electric power OFF.
From the system design, determine the external stat-
ic pressure (ESP) for the supply ducts, return ducts
and registers, diffusers, grilles, dampers, heaters
and filters.
3. To your system ESP determined in Step 2, add 0.05
In. W.C. for a wet coil.
4. From the system design, determine the desired cool-
ing airflow in cubic feet per minute (CFM).
Locate the unit's Blower Performance Data table in
the tech data sheet for the unit's voltage. (The tech
data sheet is attached to the inside of the electrical
access panel and is also published in the Parts List.)
From the table, determine the speed tap the desired
airflow requires.
6. See next section, Speed Taps, to set the blower mo-
tor speed terminal block (speed taps) determined in
the following steps.
SpeedTaps
After determining the required CFM and speed tap data
from the tech data sheet, follow the steps below to change
speeds if necessary.
NOTE: The yellow lead MUST always be connected to the
speed tap block at the common quick connect terminal.
The terminal is identified as COM. Also, this is the only lead
which is 3/16" wide. All other quick connects are 1/4" wide.
Refer to FIGURE 13 on Page 18 and the unit's wiring dia-
gram, which is attached to the inside of the electrical ac-
cess panel and is also published in the Parts List for the
desired speed tap to achieve the required CFM for the ap-
plicable model.
Cooling,Heating(HeatPump)andAuxiliary
ElectricStripHeat
NOTE: The cooling, heat pump and strip heat airflows
are all on the same speed tap. The refrigerant system
requires the same specific CFM for proper operation in
the cooling and the heat pump mode. For this reason,
cooling and heating airflow must bethe same. DO NOT
SPLITOUT INTO A COOLING SPEED AND HEATING
SPEED.
Check Before Starting
1.
2.
3.
Check that the blower motor speed terminal block is
set to the proper speed. Refer to the unit wiring dia-
gram and the Technical Labels in the Parts List.
Check to see that clean, properly sized field supplied
air filters are installed in the return air duct.
Inspect the inside of the unit to be sure that all wires
are in place and all tools, etc. are removed.
4. Replace all service access panels.
Check the unit's operation as outlined in the following
instructions. If any unusual sparking, odors or noises are
encountered, shut OFF electric power immediately. Re-
check for wiring errors, or obstructions in or near blower
motors.
Circulating Air Blower
1. Be sure electric power is OFF.
2. Set thermostat Heat-Cool selector to OFF.
3. Set thermostat fan switch to AUTO.
4. Turn electric power ON. Nothing should start run-
ning.
5. Set thermostat fan switch to ON. The circulating air
blower should come ON after a 30 second delay.
6. Reset thermostat fan switch to AUTO. The circulat-
ing air blower should go OFF after a 30 second delay.
Nothing should be running.
7. Turn electric power OFF.

_Installation Instructions Single Package Heat Pumps I
Sequence of Operation
CoolingMode:Energized(R,G,O,Y1)
De-energized(N/A)
(a) When high and low voltage is initially applied
to unit:
(1) On a call for cooling ......... :
The compressor and condenser fan willhave a delay
on and will energize after 3 minutes. The evaporator
blower motor will have a delay on and will energize
after 30 seconds. The delay on for the compressor
and the condenser fan can be by-passed by jumper-
ing the test pins on the defrost board control.
(2) When the cooling setpoint has been satis-
fied ......... :
The compressor and condenser fan will de-energize
immediately. The evaporator blower motor will have
a delay off and will de-energize after 30 seconds.
(b)Whenhighandlowvoltagehasbeenapplied
to unitfor morethan3 minutes:
(1) On a call for cooling .........:
The compressor and condenser fan will energize im-
mediately. The evaporator blower motor will have a
delay on and will energize after 30 seconds.
(2) When the cooling setpoint has been satis-
fied ......... :
The compressor and condenser fan will de-energize
immediately. The evaporator blower motor will have
a delay off and will de-energize after 30 seconds.
HeatingMode:Energized(R,G,Y1)
De-energized(13)
(a) When high and low voltage is initially applied
to unit:
(1) On a call for heating ......... :
The compressor and condenser fan will have a delay
on and will energize after 3 minutes. The evaporator
blower motor will have a delay on and will energize
after 30 seconds. The delay on for the compressor
and the condenser fan can be by-passed by jumper-
ing the test pins on the defrost board control.
(2) When the heating setpoint has been satis-
fied ......... :
The compressor and condenser fan will de-energize
immediately. The evaporator blower motor will have
a delay off and will de-energize after 30 seconds.
(b) When high and low voltage has been applied to
unit for more than 3 minutes
(1)On a call for heating ......... :
The compressor and condenser fan will energize im-
mediately. The evaporator blower motor will have a
delay on and will energize after 30 seconds.
(2) When the heating setpoint has been satis-
fied ......... :
The compressor and condenser fan will de-energize
immediately. The evaporator blower motor will have
a delay off and will de-energize after 30 seconds.
Defrost Mode:Energized (R,G,Y1) De-energized (13)
Defrost Sensor Closed
(1) On a call for defrost .........
When the defrost sensor closes (this can be simu-
lated by jumpering across reset & common on the de-
frost board control) in the heating mode,there is a
30,60 or 90 minute defrost on delay before the de-
frost mode begins. This delay is determined by the
jumper connecting to T1,T2 or T3 on the defrost
board. This delay can be by-passed by jumpering
the test pins on the defrost board control (this re-
duces the delay from 30 minutes to 7 seconds, from
60 minutes to 14 seconds and from 90 minutes to 21
seconds). In the defrost mode the reversing valve
will energize and the condenser fan will de-energize.
(2) When defrost has been completed .........
This condition will be maintained until the defrost
sensor opens (this can be simulated by removing the
jumper across reset & common on the defrost board
control) or until the defrost mode operates for 10 min-
utes (or 2 seconds iftest pins are jumpered), which-
ever comes first.

ISingle Package Heat Pumps
FIGURE 13 IBlower Motor Speed Taps (4-Speed Motors)
I
Installation Instructions
BE SURE TO CHECK BLOWER MOTOR SPEED DATA IN THE I
I
Parts List.
NOTE: THE 21/2 CANNOT BE RUN AT THE LOW SPEED TAP
SETTING. SEE Parts List FOR MORE INFORMATION.
IMPORTANT NOTE: THE BLACK AND RED LEADS ARE UNDER 1 INSULATED QUICK CONNECT AT THE MO-
TOR TERMINAL BLOCK. THE RED LEAD IS FOR ELECTRIC HEATACCESSORY BLOWER INTERLOCK. THUS,
THE COOLING/HEAT PUMP/ELECTRIC HEAT MOTOR SPEED TAP WILL ALWAYS BE ON ONE SPEED TAP. IF
THE SPEED TAP IS ADJUSTED, THE COOLING/HEAT PUMP/ELECTRIC HEAT WILL ALL BE ADJUSTED TO THE
SAME AIRFLOWS.

_Installation Instructions Single Package Heat Pumps I
9.Operation
Electrical shock hazard.
Turn OFF electric power supply at disconnect
switch or service panel before removing any ac-
cess or service panel from unit.
Failure to follow this warning can result in prop-
erty damage, personal injury, and/or death.
Defrost Control Time Interval Adjustment
Electrical shock hazard.
Turn OFF electric power supply at disconnect
switch or service panel before removing any ac-
cess or service panel from unit.
Failure to follow this warning can result in prop-
erty damage, personal injury, and/or death.
Features
Scroll Anti-Cycle Timer
All single phase heat pumps with scroll compressors are
equipped with a defrost control board which features an in-
ternal anti-short cycle timer that delays the start of the
compressor in the event of a power interruption. This fea-
ture is to allow pressure equalization throughout the sys-
tem and prevent possible reverse rotation of the scroll
compressor.
To adjust defrost interval:
1.
2.
3.
4.
Turn off all power to Heat Pump.
Remove control box cover.
Locate electronic defrost control board.
The Defrost Control Board has a jumper wire con-
nected from Wl to T1, T2, or T3. To change the time
interval, unplug the jumper wire at T1, T2, or T3
ONLY and connect it to terminal for desired time in-
terval:
T1 = 30 minutes, T2 = 60minutes, T3 = 90 minutes.
Cooling
Thermal ExpansionValves
The evaporator and condenser coil each have a Thermal
Expansion Valve for refrigerant metering. All of the valves
used on evaporator coils have internal check valves for re-
verse flow. The valves on the condenser coils may have
internal or external check valves for reverse flow. There is
also a strainer tube located just in front of each valve for
contaminant protection, along with the system bi-flow dri-
ers.
Adjust thermostat setting to desired temperature and set
thermostat Heat-Cool switch to COOL. The unit will come
on and operate automatically under control of the thermo-
stat. Close all doors and windows. The unit may run contin-
uously for several hours or longer on the initial run because
of residual heat and moisture in the house. This is normal
for any air conditioning system.
CAUTION
Do NOT operate unit on cooling when the outdoor tem-
perature is below 40°F (4.4°C). This is necessary to
prevent possible damage to the compressor.
Loss of Charge Pressure Switch
A low pressure switch on the liquid line (high side) has been
installed to prevent system damage due to a loss of charge.
The switch will open and de-energize the contactor if the
high side pressure drops below the set point of the switch.
TurningThe Unit Off
1. Set the thermostat selector switch to OFF and set the
fan switch to AUTO. To restart, set thermostat selec-
tor switch to COOL and set thermostat to tempera-
ture desired.
2. To shut the unit down completely, turn electric power
OFF.