ICRealtime AVS-D2118VF User manual

1 Megapixel HD-AVS IR Vari-focal Vandal-proof Dome Camera
User's Manual
Version 1.0.1

i
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Functions .......................................................................................................................1
1.4 Specifications................................................................................................................2
2Framework and Dimensions.....................................................................................................3
3Installation....................................................................................................................................4
Appendix Toxic or Hazardous Materials or Elements .................................................................7

ii
Welcome
Thank you for purchasing our HD-AVS camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC (24V AC) in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series camera should be installed in a cool, dry place away from direct sunlight or strong light,
inflammable, explosive substances and etc.
This series camera shall work on the specified working temperature. Please keep it away from the
electromagnetic radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iv
Use the dry soft cloth to clean the device.
If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

v
Applicable Model
This manual can be applied to the following model:
AVS-D2118VF

1
1General Introduction
1.1 Overview
This series megapixel HD camera conforms to the HD-AVS standard. It supports video signal high-speed
long distance transmission without any delay. It can be controlled by the DVR conforming to the HD-AVS.
1.2 Features
High-performance CMOS image sensor, megapixel definition.
Support HD-AVS video output.
Support 75-3 coaxial cable transmission without any loss. Transmission distance is over 500m.
High speed, long distance real-time transmission.
Support ICR switch to realize surveillance both in the daytime and at night.
Support auto exposure, auto white balance, auto electronic shutter and auto gain function.
High image color rendition, vivid image.
Support manual adjustment of lens zoom and focus.
Support DC12V power supplying.
Support IP66,IK10 compliance
Support intelligent IR function, max IR distance 30m.
1.3 Functions
HD-AVS Specification
HD-AVS is an over-coaxial –cable HD video transmission standard. The technology renders two HD video
formats by progressive scanning.
ICR
The IR cut removal is to filter the IR light in the daytime and then auto switch to the general fitter at night.
This function allows the camera to output the high sensitivity and clear video.
Smart IR technology
The sensor controls the IR light on/off via the combination work of the hardware and software, which
realizes the automatically IR light compensation according to the environment illumination.
Auto gain function
To output the standard video signal in the different illumination environments, the amplifier needs to adjust
in a wide range. The system can enhance the camera sensitivity in low illumination and enhance the video
signal output to get the clear and high definition video.
Auto white balance
The white balance refers to the camera to restore the white object color. It allows the camera to
automatically adjust the color temperature in indoor and outdoor environment, just like our human eyes
does.
Auto exposure

2
System can automatically set shutter speed and iris value according to the snapshot video exposure
condition.
Auto electronic shutter
The system can automatically adjust the electronic shutter when the environment light changes.
1.4 Specifications
Model
Parameter
1 Megapixel HD-AVS IR Vari-focal Vandal-proof Dome Camera Series
AVS-D2118VF
Video Processor
1/2.9" 1.0 Mega Pixels CMOS
Video Format
PAL/NTSC
Effective Pixel
1280（H）* 720（V）
Min Illumination
0.01Lux @（F1.2,AGC ON），0Lux with IR
Electronic Shutter
PAL：1/50s~1/100,000s
NTSC：1/60s~1/100,000s
Video Standard
HD-AVS compliance
Video Frame Rate
PAL：1280×720@25 fps
NTSC：1280×720@30 fps
Lens Port
Φ14
Lens Type
2.7-12 mm @F1.4 fixed iris manual vari-focal lens
Day/Night Switch
ICR auto switch
Sync Mode
INT
Video Output
1-channel HD-AVS high definition video output
White Balance
Auto
Gain Control
Auto
BLC
Auto
Smart IR
Support
Transmission
Distance
Over 500m via 75-3 coaxial cable without any loss
Max IR Distance
30m
Protection Level
IP66
IK Rating
IK10
Working Temperature
/Humidity
-30℃~+60℃. Humidity is less than 95%(no condensation)
Power
DC 12V±10%
Power Consumption
3.9W MAX (Input: 12V 0.32A)
Dimension(mm)
Φ90.4×213
Weight
450g
Installation Mode
Wall mount/In-ceiling mount

3
2Framework and Dimensions
Please refer to the following figures for dimension information. The unit is mm. See Figure 2-1 to
Figure 2-3.
Figure 2-1
Figure 2-2
Figure 2-3

4
3Installation
Important
Before the installation, please make sure the installation surface can sustain at least 3X weight
of the bracket and the camera.
The dome camera usually uses the ceiling installation. It can be installed on the ceiling or the wall. Please
refer to Figure 3-1 for installation hole site.
For side exit cable installation, please make sure the side exit cable direction is the same as shown in
the installation position map.
Before you secure the screws on the pedestal, please put the cable through the cable exit of the
pedestal.
Before you complete the installation and debug, do not remove the electrostatic film. After you remove
the film, do not touch the enclosure in case there is any scratch.
Figure 3-1

5
Figure 3-2
Step 1
Take the installation position map from the accessories bag and then put it on the surface of the ceiling or
the wall according to the cable exit position. Dig three holes according to the installation position map and
then take three expansion bolts from the accessories bag and put them to the holes you just dug.
Step 2
Use inner hex wrench to remove the three case locking screws and then remove the dome enclosure.
Step 3
Adjust the pedestal position according to the cable exit mode (ceiling/side). Pull the cable through the
cable side exit at the installation surface and the pedestal (Please skip this step if you want to use ceiling
exit mode). Line up the screw holes at the bottom of the pedestal to the expansion bolts in the installation
surface. Put three self-tapping screws to expansion bolts and then secure firmly. Now the pedestal is on
the installation surface.
Step 4

6
After you adjust clear image with focus lever, adjust the dome module to an appropriate angle for
monitoring according to the direction which is shown in Figure 3-1, lock the screw and fix it.
Step 5
Use three case locking screws to secure the dome housing on the pedestal.
Now you have completed the device installation and cable connection.
You can use the terminal encode devices to view the monitor video.

7
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board
Component
○
○
○
○
○
○
Device
Construction
Material
○
○
○
○
○
○
Wire and Cable
○
○
○
○
○
○
Packing
Components
○
○
○
○
○
○
Accessories
○
○
○
○
○
○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts
is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements contained
in products will not leak or mutate so that the use of these (substances or elements) will not result in any
severe environmental pollution, any bodily injury or damage to any assets. The consumer is not authorized
to process such kind of substances or elements, please return to the corresponding local authorities to
process according to your local government statutes.
Note
This manual is for reference only. Slight difference may be found in the user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more information.