ICRealtime ICIPD2730 User manual

HD IR Vari-focal Dome Network Camera
User’s Manual
Version 1.0.0

i
Welcome
Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1

iv
Table of Contents
1General Introduction .................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
2Structure .....................................................................................................................................6
2.1 Components..................................................................................................................6
2.2 Framework and Dimension.........................................................................................7
2.3 Alarm Setup...................................................................................................................7
3Device Installation ...................................................................................................................10
3.1 Installation Steps ........................................................................................................10
3.2 Micro SD Card Installation........................................................................................11
3.3 Lens Adjustment.........................................................................................................12
4Quick Configuration Tool........................................................................................................13
4.1 Overview......................................................................................................................13
4.2 Operation.....................................................................................................................13
5Web Operation.........................................................................................................................15
5.1 Network Connection...................................................................................................15
5.2 Login and Main Interface...........................................................................................15
Appendix Toxic or Hazardous Materials or Elements ...............................................................17

1
1General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary
device.
This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.
It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The waterproof design conforms to the IP 66 level. It has the sound waterproof function suitable for
use in the outdoor environments.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such office, bank, road monitor and etc.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
Storage
Function
Support central server backup function in accordance with your configuration
and setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end
PC.
Support network storage function such as FTP.
Alarm
Function
Real-time respond to external on-off alarm input, and video detect as user
pre-defined activation setup and generate corresponding message in screen
and audio prompt(allow user to pre-record audio file)
Real-time video detect: motion detect, camera masking.
Alarm occurs when network is abnormal.
Network
Monitor
Network camera supports one-channel video data transmit to network
terminal and then decode. Delaying time is within 270ms (network bandwidth
support needed)
Max supports 20 connections.
Adopt the following video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
Support web access.
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Support abundant network protocol.
Power
External power adapter DC 12V.
Support PoE.
Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
Assistant
Function
Log function
Support system resource information and running status real-time display.
Day/Night mode auto switch.
Support picture parameter setup such as electronic shutter and gain setup.

2
Support motion detect.
Backlight compensation: screen auto split to realize backlight compensation
to adjust the bright.
Support video watermark function to avoid vicious video modification.
Built-in IR light. Support IR night vision.
1.3 Specifications
Please refer to the following sheet for network camera performance specification.
Model
Parameter
ICIP D2730
ICIP D3730
System
Main Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the same
time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/2.8-inch CMOS
1/3-inch CMOS
Pixel
1920(H)*1080(V)
2048(H)*1536(V)
Day/night
Support day/night mode switch
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Electronic
Shutter
Manual/Auto
It ranges from 1/3 to 1/100000
Video
Compression
Standard
H.264/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream (1920*1080@25fps),
extra stream 1 ( 704*576@25fps)
extra stream 2 ( 1280*720@11fps)
PAL:
Main stream (2048*1536@20fps),
extra stream 1 ( 704*576@20fps)
extra stream 2 (1280*720@1fps)
Main stream (1920*1080@25fps),
extra stream 1 ( 704*576@25fps)
extra stream 2 (1280*720@11fps)
NTSC:
Main stream (1920*1080@30fps),
extra stream 1 ( 704*480@30fps)
extra stream 2 ( 1280*720@1fps)
NTSC:
Main stream (2048*1536@20fps),
extra stream 1 ( 704*480@20fps)
extra stream 2 (1280*720@1fps)
Main stream (1920*1080@30fps),
extra stream 1 ( 704*480@30fps)
extra stream 2 (1280*720@1fps)
Note:
The exact frame rate of extra stream 2 is decided by the max capacity set of
the device, it is dynamic and adjustable within the range of capacity set.
Video Bit Rate
H.264H: 40-8192Kbps adjustable
MJPEG: 40～16384kbps adjustable
and bit rate is adjustable. Support customized setup. (Actual bit rate is based
on the device adjustable range)
Video Flip
Support mirror.

3
Support flip, rotation mode function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
ROI
Support max 4 ROI zones
Video Setup
Support parameter setup such as bright, contrast, acutance
Video
Information
Channel title, time title, motion detect, camera masking, overlay
Lens
2.8～12mm/F1.4（manual focus）
Lens Interface
Φ14 interface. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold ranges from 0 to 100.
Video Loss
Sensitivity level 1-6, each sensitivity level is corresponding to the percentage
of the video area which is masked.
Activation event: Audio/ video storage, image snapshot, log, email SMTP and
etc.
Record
Record Priority
Manual >Video detect>Schedule
Storage
Management
NAS Storage
Network
Wire Network
1-ch Ethernet Port, 10/100 Base-T Ethernet
Network
Protocol
Standard HTTP, TCP/IP, ARP,IGMP, ICMP, RTSP, RTP,UDP, RTCP, SMTP,
FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP, QoS,
802.1x.
Platform
Standard
PSIA, ONVIF
Remote
Operation
Monitor, system setup, file download, log information, maintenance , upgrade
and etc
General Parameter
Power
DC12V power and PoE.
Power
Consumption
4.4W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(m
m)
¢122×89
Weight
450g
Installation
Ceiling and wall mount
Model
Parameter
ICIP D2732Z
ICIP D3732Z
System
Main
Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the same
time.
User Interface
Remote operation interface such as WEB, DSS, PSS

4
System
Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/2.8-inch CMOS
1/3-inch CMOS
Pixel
1920(H)*1080(V)
2048(H)*1536(V)
Day/night
Support day/night mode switch
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Electronic
Shutter
Manual/Auto
It ranges from 1/3 to 1/100000
Video
Compression
Standard
H.264/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream (1920*1080@25fps),
extra stream 1 ( 704*576@25fps)
extra stream 2 ( 1280*720@11fps)
PAL:
Main stream (2048*1536@20fps),
extra stream 1 ( 704*576@20fps)
extra stream 2 (1280*720@1fps)
Main stream (1920*1080@25fps),
extra stream 1 ( 704*576@25fps)
extra stream 2 (1280*720@11fps)
NTSC:
Main stream (1920*1080@30fps),
extra stream 1 ( 704*480@30fps)
extra stream 2 ( 1280*720@1fps)
NTSC:
Main stream (2048*1536@20fps),
extra stream 1 ( 704*480@20fps)
extra stream 2 (1280*720@1fps)
Main stream (1920*1080@30fps),
extra stream 1 ( 704*480@30fps)
extra stream 2 (1280*720@1fps)
Note:
The exact frame rate of extra stream 2 is decided by the max capacity set
of the device, it is dynamic and adjustable within the range of capacity set.
Video Bit Rate
H.264H: 40-8192Kbps adjustable
MJPEG: 40～16384kbps adjustable
and bit rate is adjustable. Support customized setup. (Actual bit rate is
based on the device adjustable range)
Video Flip
Support mirror.
Support flip, rotation mode function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
ROI
Support max 4 ROI zones
Video Setup
Support parameter setup such as bright, contrast, acutance
Video
Information
Channel title, time title, motion detect, camera masking, overlay
Lens
2.8～12mm/F1.4（motorized vari-focal）
Lens Interface
Φ14 interface. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold ranges from 0 to 100.
Video Loss
Sensitivity level 1-6, each sensitivity level is corresponding to the
percentage of the video area which is masked.

5
Activation event: Audio/ video storage, image snapshot, log, email SMTP
and etc.
Record
Record
Priority
Manual >Video detect>Schedule
Storage
Management
NAS Storage
Network
Wire Network
1-ch Ethernet Port, 10/100 Base-T Ethernet
Network
Protocol
Standard HTTP, TCP/IP, ARP,IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP,
QoS, 802.1x.
Platform
Standard
PSIA, ONVIF
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc
General Parameter
Power
DC12V power and PoE.
Power
Consumption
9.1W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(
mm)
¢122×89
Weight
450g
Installation
Ceiling and wall mount

6
2Structure
Note:
There are differences about wire structure for some product models, please refer to the actual object
for more details.
2.1 Components
You can refer to the following figure for component structure. See Figure 2-1.
Figure 2-1 Component structure
Please refer to the following sheet for detailed information.
Component
Component Name
Component 1
Dome body
Component 2
Dome enclosure

7
Please refer to the following sheet for detailed information about I/O port.
Port
Name
Port
Sequence
Port name
Function Description
I/O Port
1
ALARM_IN1
Alarm input port, receive on-off signal of
external alarm source.
2
ALARM_OUT1
Alarm output port, output alarm signal to
alarm device.
3
ALARM_GND
Connect ground
2.2 Framework and Dimension
Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2
Figure 2-2 Dimension illustration
2.3 Alarm Setup
Port
Port Name
Note
Port 3
Power input port
Connect to DC 12V power, input power.
Port 4
I/O port
Alarm signal input/output (optional,
supported by some product models)
Port 5
Internet access port
Network data in/out and PoE.
Note:
Some devices do not support PoE.
Port 6
Audio input port
Input audio signal, receive analog audio
signal from sound pick-up.etc(optional,
supported by some product models)
Port 7
Audio output port
Output audio signal to speakers.etc
(optional, supported by some product
models.)

8
Note:
Only supported by some series products.
Alarm input, output description:
Step 1 Connect alarm input device to the alarm input of I/O cable.
Step 2 Connect alarm output device to the alarm output of I/O cable, alarm output is collector open
circuit output which connects 10K resistor to 3.3V externally.
Step 3 Open the Web, set alarm input and output correspondingly. Alarm input on WEB
corresponds to I/O cable on device. When there is alarm, alarm input device will generate
signal of high and low level. Set corresponding NO and NC inputs.
Step 4 Set the WEB alarm output. The alarm output is for the alarm output port of the device. It is the
alarm output port of the I/O cable.
Please refer to the following figure for alarm input information. See Figure 2-3.
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of
the alarm input port. When the input signal is connected to 3.3V or idle, the device collects the logic “1”.
When the input signal is grounded, the device collects the logic “0”.
Figure 2-3
Please refer to the following figure for alarm output information. See Figure 2-4
Alarm output: Alarm output is OC door, requiring increase of external pull-up resistor. Output signal is
high and low levels. After pull-up resistor is increased, output signal is high level by default. When
there is alarm output, output signal becomes low level.

9
Figure 2-4

10
3Device Installation
3.1 Installation Steps
Manual Focus Camera Motorized Vari-focal Camera
Figure 3-1
Important
Before the installation, please make sure the installation environments can at least support 3x
weight of the camera.
Please follow the steps listed below to install the device. Please refer to Figure 3- for reference.
Step 1
Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner hex
screws on enclosure.
Step 2
Please take the installation position map in the accessories bag, and then paste it on the ceiling or the
wall according to your monitor area requirements.
Step 3
Find cross signs on the map, and dig three plastic expansion bolts holes in the installation surface and
then insert three expansion bolts in the holes. Secure these three bolts firmly.
Note:
If use pulls out cable from top of installation surface, you must dig a exit hole on installation
surface according to the installation position map.
If user pulls out cable from side of cable channel, it must go through the U-shape channel on
dome pedestal, and take out cable from the side exit hole on pedestal.
Step 4
Adjust the device installation pedestal to the proper position and then pull cable through the exit hole
on Installation surface. Make direction of TOP sign same as it on installation position map. Line up the
three screw holes in the device pedestal to the three plastic expansion bolt holes in the installation
position. Put the three self-tapping screws in the three plastic expansion bolts firmly. Fix dome body on
installation surface.
Step 5

11
Hold rotating bracket on both sides with hand, horizontally rotate bracket, adjusting lens horizontal
direction to designated position. Loosen two hand screws on both sides of fixed rotating bracket.
(Loosen only, do not take it down), hold the camera module body with hand, making lens rotate
vertically. Adjust vertical direction of lens to appropriate angle, and fasten the M2 screw. Range of lens:
vertical (0°～+75°), horizontal (0°～+355°). See Figure3-2.
Figure 3-2
Step 6
Take dome enclosure, put it back on the camera properly regarding to screw and hole, and fasten the
three inner hex screws with wrench.
3.2 Micro SD Card Installation
Note:
Some series products do not support the Micro SD card storage function. Please shut down the power
and then turn off the device before you install the Micro SD card.
Step 1 Find the Micro SD Card slot in figure 3-3, open the Micro SD Card slot according to the
direction in figure 3-4.
Step 2 Adjust the Micro SD Card to proper direction and install it in the Micro SD card slot.
Step 3 According to the direction in figure 3-4, close the Micro SD card slot and keep it locked.

12
Figure 3-3 Micro SD Card installation illustration 1
Figure 3-4 Micro SD Card installation illustration 2
3.3 Lens Adjustment
After you take off the dome housing, you will see the adjusting screw nut of the lens, adjusting screw
nut C is for zoom function, adjusting screw nut D is for focus function. Make sure to lock the adjusting
screw after the image is clear. See figure 2-5 for more information.
Note:
The dome housing is related to device waterproof function, be sure to screw it firmly after
adjustment
Motorized Vari-focal lens is default in motorized Vari-focal series, no need to adjust manually.
Figure 3-5

13
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface. In the device list interface, you can
view device IP address, port number, subnet mask, default gateway, MAC address and etc.
Select one IP address and then right click mouse, you can see an interface is shown as in figure 4-1
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 4-1 Search interface
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-2.
In Figure 4-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.

14
Figure 4-2 Login prompt
After you logged in, the configuration tool main interface is shown as below. See Figure 4-4.
Figure 4-3 Main interface
For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

15
5 Web Operation
This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.
5.1 Network Connection
Please follow the steps listed below for network connection.
Make sure the network camera has connected to the network properly.
Please set the IP address, subnet mask and gateway of the PC and the network camera
respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1
Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.
5.2 Login and Main Interface
Open IE and input network camera address in the address bar. See Figure 5- 1.
Figure 5- 1 IP address
The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here