ICRealtime ELIP-3000N User manual

QUICK INSTALLATION GUIDE
2MP 12X SMART ZOOM SUPER NIGHT VISION OUTDOOR CAMERA
Dear Customers!
By selecting this product, you have decided to use a professional device that
guarantees highest quality and reliability. We would like to thank you very much
for your confidence and kindly ask you to read the following instructions carefully
before installation and operation in order to take full advantage of all quality
features regarding this product.
The lighting flash with an arrowhead symbol, within an equilateral triangle
is intended to alert the user to the presence of non-insulated dangerous
voltage within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
INFORMATION
This installation should be made by a qualified service person and should
conform to all local codes.
WARNING
Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
Precautions
Limitation of liability
Disclaimer of warranty
1. PRODUCT OVERVIEW
2. NAME AND FUNCTION OF EACH PART
2. NAME AND FUNCTION OF EACH PART
3. INSTALLATION & CONNECTION
• Please read the manual carefully before the installation in order to set up the
camera correctly and to obtain the best picture quality.
• Please keep the manual in good condition for your future reference and service
application.
• Installation and services should be only carried out by an authorized personnel
according to local safety regulations.
• If any liquid or solid matter gets into the housing, immediately disconnect the
camera from power supply and have it checked by your authorized dealer before
reusing.
• Avoid installing the camera at extremely hot or cold places.
• Avoid installing the camera at a place of high humidity.
• Avoid installing the camera at the place exposed to gas or oil.
• If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers.
There are no parts inside that need maintenance by the user.
All maintenance should be carried out by qualified personnel.
• Keep the top glass of the lens always clean in order to obtain the best picture
quality all the time. Be careful not to be stained by fingerprint.
• Don't face the camera directly toward sunlight or sunlight reflecting area.
IMAGE SENSOR may go defective at this condition.
• Please give a special attention to keep the unit from dangerous drop or external
shock during the process of transportation or handling.
• Never try to touch the camera in wet hand. It may cause an electric shock.
• Do not expose the camera to radioactivity. It causes a serious damage on the
IMAGE SENSOR.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
Please read this manual carefully before installation and operation of the product.
ELIP-3000N
NIGHT VISION OUTDOOR
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
its own expense.
CAUTION – To prevent electric shock and risk of the fire hazards
Trademarks
- Do NOT use power source other than that specified.
- Do NOT expose this appliance to rain or moisture.
All names used in this manual for hardware and software are probably registered
trademarks of respective companies.
This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability,
fitness for any particular purpose, or non-infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors.
Changes are added to the information herein, at any time, for the improvements
of this publication and/or the corresponding product(s).
In no event shall seller be liable to any party or any person, except for
replacement or reasonable maintenance of the product, for the cases, including
but not limited to below:
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product;
(2) Personal injury or any damage caused by inappropriate use or negligent
operation of the user
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any
reason or cause including any failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of
the system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization
being photogenic subject, due to violation of privacy with the result of that
surveillance-camera's picture, including saved data, for some reason,
becomes public or is used for the purpose other than surveillance.
• 2 Mega pixel 1/2.8" SONY progressive scan CMOS image sensor for excellent
image quality (Exmor)
• 5~60mm Motorized Megapixel Lens
• 50M IR Beam Distance
• Smart Focus Function
• Multi Streaming of H.264 and MJPEG
• Supports image resolution up to 30fps @ 1920x1080 (FHD)
• Supports CBR and CVBR modes
• Controllable frame rate
• Privacy Masking up to 8 area
• WDR using frames of Long and Short exposure
• Supports Defog, 2D+3DNR, Sense-Up
• Digital PTZ
• 12VDC / IEEE802.3af POE
• Conformant with ONVIF
• Includes Windows based IP Installer and license-free 16 channel NVR
(Network Video Recorder) software
Classification
Image Sensor 2.0 Megapixel 1/2.8" Sony progressive scan CMOS image sensor
Image
Pickup
Video
Network
Physical
Environment
※Specifications are subject to change without prior notice for improvement.
ELIP-3000N
KEY FEATURES
2.1 PACKAGE CONTENTS
SPECIFICATION
2.1.1 ELIP-3000N
2.2 NAME AND FUNCTION
2.2.1 ELIP-3000N
3.1 AXIS ADJUSTMENT
Total Pixels 1952(H) x 1116(V) 2.18 Megapixel
Effective Pixels 1944(H) x 1104(V) 2.14 Megapixel
S/N Ratio 50dB
Min. Illumination 0Lux (IR On)
Frame rate H.264 : 30fps @ 1920 x 1080P
MJPEG : 30fps @ VGA
Dual Stream : H.264, MJPEG
Bit rate Control H.264: CBR / CVBR
Image setting
Day & Night
Auto White Balance
Privacy Mask
WDR (Off / Low / Middle / High)
Defog (On / Off)
Smart IR (Off / 0~16)
3DNR (On / Off)
Output (Optional) BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC / PAL
Security
Password protection
User access log
HTTPS encryption
Protocol HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DDNS, NTP, RTSP, RTP,
TCP, UDP, ICMP
Intelligent video Motion detection with 4 x 3 blocks
Power source
Storage (Optional)
DC 12V / 1.5A, PoE (Power over Ethernet): 802.3af
Micro SD Slot
Power Consumption Max 11W (IR On)
Net Weight 2600g
Status LED N/A
Reset Button Factory Reset
104.3(Ø) x 137.3(H) x 333.3(D)Dimension (mm)
Operating
Temperature -10°C ~ 50°C
Storage
Temperature -20°C ~ 60°C
Alarm In / Out
(Optional) In : 1, Out : 1
Auto Exposure
IR Distance 50M
Day & Night ICR Filter Changer
Lens 5~60mm Motorized
Megapixel Lens
Video
compression H.264 High profile @ Level 4.0, Motion JPEG
Resolution Max 1920 x 1080
APPEARANCE DESCRIPTION
IP Camera x 1
Installation Guide x 1
Tapping screws x 3
Plastic anchor x 3
L-Wrench x 1
CD x 1
1 2 3 4 5 6
8
7
9
10
◆3-Axis mounting mechanism
▪ Rotating axis up to 360 degree
▪ Panning axis up to 360 degree
▪ Tilting axis up to 180 degree
1
NO. ITEM
Audio-In Audio in (RED)
Audio-Out Audio out (WHITE)
PoE (Power over Ethernet) and Lan cable
Sensor In / Alarm out
Analog Video Out (YELLOW)
DC12V
Infrared LED
Network and POE
Connector
Sensor In / Alarm Out
BNC
Power Connector
IR LED
Sunshield
Motorized Megapixel Lens
Control IR LED by sensing light
Lens
Illuminance sensor
DESCRIPTION
2
3
4
5
6
7
8
9
10
① Pan 360˚
Slightly loosen Pan bolt then
adjust pan of the camera using
a serration on the bracket and
tighten the bolt firmly.
② Tilt 180˚
Slightly loosen Tilt bolt then
adjust tilt of the camera using
a serration on the bracket and
tighten the bolt firmly.
③ Rotation 360˚
Slightly loosen Tilt bolt then
adjust rotation of the camera
using a serration on the bracket
and tighten the bolt firmly.
1. PRODUCT OVERVIEW
PAN 360°
ROTATION 360°
TILT 180°
Pan bolt
Tilt bolt
Rotation bolt
1 2 3 4 5 6

4. Dimension (mm)
< Ceiling Mount >
< Wall Mount >
3. INSTALLATION & CONNECTION
3. INSTALLATION & CONNECTION 3. INSTALLATION & CONNECTION
3.2 HOW TO MOUNT TO CEILING / WALL
ID
PW
Login
LOGIN
Ip Camera XX http://192.168.1.32/
150521-1
3.3 HOW TO INSTALL A MICRO SD CARD
3.4 INSTALLATION EXAMPLE
3.4.1 Installation Example
www
LAN Switch
Local Access
Remote Access
e-mail / FTP
Router Internet
3) The MAC address can be found on the label of the camera or video server.
4) From the cameras or video servers listed, select one and click “IP Change to
assign a new IP address.
5) Select DHCP or STATIC, then change IP address.
Default ID and password are “admin" and “1234” respectively.
3.4.3 Accessing the Camera or video server’s Homepage
1) After you assign IP address to your IP camera or video server and enter that
camera or video server address on the Web Browser, you will be connected
to the login page of the camera or video server as shown below.
2) Enter a ID (username) and password to access the camera or video server.
The default ID and password are “admin” and “1234”.
3) The first time you login to the camera or video server using ActiveX, you are
notified that a required ActiveX control is required. You need to allow the
installation of ActiveX by clicking "Yes". It is normal for this process to take
up to 30 seconds.
※For more information, see the manual of IP camera or video server in the
packaged CD.
3.4.2 Connecting Network
1) Run IPScan Utility program in the packaged CD.
2) Click “Scan” button. Once IPScan Utility program scanned, the panel shows
every camera or video server connected on the local network.
Use DHCP Address Use Static Address
Start IP Address
Gateway Address
Subnet Mask
MAC Address
00:26:e6:00:28:ad
IP Address
10.0.0.7 10.0.0.7 10.0.0.254 Sratic 2700 81
Change IPAddress Change Gateway A... IP Type Stream Port HTTP Port ID PW
IP Change
10 . 0 . 0 . 7
10 . 0 . 0 . 254
255 . 0 . 0 . 0
Ports
Login
User ID Password
Stream Port HTTP Port:2700 81
X
Scan
Clear
Network Card:
IP Address MAC Address IP Type Stream Port HTTP Port Upgrade Port Server Name
Protocol : Version2
Count : 0
-- Auto select --
IP Change Upgrade Factory Default
Scan
Clear
Network Card:
IP Address MAC Address IP Type Stream Port HTTP Port Upgrade Port Server Name
Protocol : Version2
Count : 0
-- Auto select --
IP Change Upgrade Factory Default
0.0.0.7 00:26:e6:00:28:ad Static 2700 81 9300 VD102i
① Open the cap on the bottom of the camera by turning it anticlockwise.
And Slide the upper part of Micro SD Card slot horizontally in the direction
shown by the “OPEN” arrow (*Slot is a hinge type).
② Insert a Micro SD Card to the slot.
③ Slide the upper part in the direction shown by the “LOCK” arrow.
④ Close the cap in a clockwise direction
<Caution>
a. Please turn the power off before inserting or removing a Micro SD card.
b. Make sure to close the cap carefully and quickly to keep it water-tight and
anti-fog.
①Drill three screw holes on the wall or ceiling plate to fix three anchors (supplied)
in the holes.
②Fix the plastic anchors in the holes.
③Position the mounting bracket on the screw points.
④Fix the mounting bracket by tightening the screws.
⑤Slightly loosen bolt (A), (B) then adjust TILT (180°) and PAN (360°) of the
camera and tighten the bolt firmly.
⑥Slightly loosen bolt (C) then adjust ROTATION (360°) of the camera and
tighten the bolt firmly.
SD Card
slot
SD Card
FACTORY
RESET
micro
sd
OPENLOCK
96
Ø96
104.3
137.3
(C) (B) (A)
(C)
(B)
(A)
Mount Screw
(Ø4X30L-3EA)
Plastic Anchor
Right turn
(Tightening) Left turn
(Loosening)
31 156.3 50
292.3
96
Ø110