ICU MSD-400 User manual

Ver 1.110
1

INSTALLATION & SAFEGUARDS
All the safety and operating instructions should be read before operation.
Environment Condition for Installation
1. To prevent electric shock or other hazard, do not expose this unit to rain, moisture, or dust.
2. Place this unit in a well-ventilated place and do not place heat-generating objects on this
unit.
3. This unit should not be located in an area where it is likely to be subjected to mechanical
shocks.
Before You Start
1. Ensure the power switch is in the OFF position prior to installation.
2. Opening or removing the cover may expose you to dangerous voltage or other hazards.
3. Operate this unit within the range of room temperature and humidity.
4. Supply power through the type of power source indicated on the manufacturer’s label and
with the
p
ower su
pp
l
y
included in this unit.
pppy
5. Keep this unit out of direct sunlight and heat .
6. Make sure conductive material does not go into the fan hole.
Notice
1. Before initial configuration or operation, first set TIME/DATE, and then set this unit to the
FACTORY DEFAULT setting, and lastly HDD clear. Follow these steps in order. Otherwise it
may cause non
-
recording on the HDD or non saving setting value. Or it may record, but you
may
cause
non
recording
on
the
HDD
or
non
saving
setting
value.
Or
it
may
record,
but
you
will not be able to search recorded data.
2. This unit is compatible with large sized HDD.
3. When setting RECORDING SETUP after installation, set not only RECORD CONFIGURATION,
but also SCHEDULE SETUP. Setting Schedule setup is necessary as this unit records
according to Record type & Schedule setup. Default setting value for Schedule setup is
Continuous mode.
4. Stop recording before powering off this unit by entering setup menu. Powering off while
recordin
g
ma
y
cause critical malfunctions such as Recordin
g
Error, Pla
y
back Error, or S
y
stem
gy g y y
Error.
FCC Information
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when
the e
q
ui
p
ment is o
p
erated in a commercial environment.
qp p
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operated the equipment under FCC rules.
2

CONTENTS
CHAP. 1 General Information ---------------------------------------------------------------- 5
1-1. Package Contents &
Description ---------------------------------------------------------------- 5
CHAP. 2 Function of Buttons ---------------------------------------------------------------- 6
2-1. Front Panel ---------------------------------------------------------------- 6
2-2. Rear Panel ---------------------------------------------------------------- 8
CHAP. 3 Installation ---------------------------------------------------------------- 10
3-1. Configuration ---------------------------------------------------------------- 10
3-2. Detailed Configuration ---------------------------------------------------------------- 11
1
)
Rack Mount ---------------------------------------------------------------- 11
)
2) HDD (Hard Disk Drive) ---------------------------------------------------------------- 11
3) Camera ---------------------------------------------------------------- 13
4) Audio ---------------------------------------------------------------- 13
5) Monitor ---------------------------------------------------------------- 14
6
)
Power Cable ---------------------------------------------------------------- 14
)
7) SPOT Output, Video Printer ---------------------------------------------------------------- 14
8) Others ---------------------------------------------------------------- 15
CHAP. 4 Display Configuration ---------------------------------------------------------------- 17
4-1. Display ---------------------------------------------------------------- 18
4
2
Main Menu
19
4
-
2
.
Main
Menu
----------------------------------------------------------------
19
4-3. Record, Playback Panel ---------------------------------------------------------------- 22
4-4. Panic Recording ---------------------------------------------------------------- 22
4-5. SEARCH ---------------------------------------------------------------- 23
4-6. PAN/TILT/ZOOM Control ---------------------------------------------------------------- 24
4
-
7
Data Backup (CD/DVD)
----------------------------------------------------------------
24
4
7
.
Data
Backup
(CD/DVD)
24
4-8. Data Backup (USB) ---------------------------------------------------------------- 25
CHAP. 5 Operation ---------------------------------------------------------------- 26
5-1. System Login ---------------------------------------------------------------- 26
5-2. Factory Default ---------------------------------------------------------------- 26
5
-
3
Key Lock
----------------------------------------------------------------
27
3
5
3
.
Key
Lock
27
5-4. Playback ---------------------------------------------------------------- 27

CHAP. 6 DVR Setup ---------------------------------------------------------------- 28
6-1. General Operation ---------------------------------------------------------------- 28
6-2. SYSTEM Setup ---------------------------------------------------------------- 29
6-3. DISPLAY Setup ---------------------------------------------------------------- 32
6-4. RECORD Setup ---------------------------------------------------------------- 34
6
5
CAMERA Setup
36
6
-
5
.
CAMERA
Setup
----------------------------------------------------------------
36
6-6. DEVICE Setup ---------------------------------------------------------------- 38
6-7. NETWORK Setup ---------------------------------------------------------------- 40
CHAP . 7 Network Setup ---------------------------------------------------------------- 43
6-8. Language Setup ---------------------------------------------------------------- 42
7-1. DVR Network ---------------------------------------------------------------- 43
7-2. DDNS ---------------------------------------------------------------- 45
7-3. Web Application ---------------------------------------------------------------- 46
CHAP. 8 Remote Viewer Program ---------------------------------------------------------------- 48
8-1. IRS Operation ---------------------------------------------------------------- 48
8-2. Backup Operation ---------------------------------------------------------------- 51
8-3. Transmitter Operation ---------------------------------------------------------------- 53
8-4. Player Operation ---------------------------------------------------------------- 59
CHAP. 9 Specification / Dimension ---------------------------------------------------------------- 62
CHAP.10 Remote Controller ---------------------------------------------------------------- 64
4

1
1
Package
Contents & Description
1. General Information
1
-
1
.
Package
Contents
&
Description
1. DVR Main Unit 2. Remote Control
3. Power Cable 4. Power Adapter 5. User’s Manual 6. Software CD
7. Rubber Pad 8. HDD Absorber 9. Rack Mount Bracket
HDD Bolts 10. Mouse
8. Batteries
Contents Description
1 DVR Main Unit
Stand
-
Alone DIGITAL VIDEO RECORDER
1
.
DVR
Main
Unit
Stand
Alone
DIGITAL
VIDEO
RECORDER
2. Remote Control Remote Control
3. Power Cable AC power supply to adapter
4. Power Adapter DC power supply
5. User’s Manual User’s Manual
6. Software CD Remote Viewer SOFTWARE
7. Rubber Pad Prevent DVR from slipping by attaching on the bottom of the unit
8. HDD Absorber Absorbing the mechanical shock of HDD against the case bottom
9. Batteries Batteries for Remote Control
10. Rack Mount Bracket /
Bolts
Rack Mount Bracket / 6 Bolts for fixing Rack Mount Bracket to DVR / 4 Bolts
for fixing DVR with Rack Mount Bracket to 19” Rack / 8 Bolts for fixing HDD
into DVR
5
11. Mouse DVR function control

2
-
1
Front
2. Function of Buttons
2
1
.
Front
1 2 3 4 5
Name Function
1LEDL
St t f ti
6 7 8
1
.
LED
L
am
p
s
St
a
t
us o
f
o
p
era
ti
on
2.Jog Shuttle Jog shuttle activate only when in Pause: Pressing Jog Shuttle button will pause
playback.
Rotating clockwise causes it to move into ever-faster forward speed, and
counter-clockwise causes it to move into ever-faster reverse speed.
In Setup Menu, its rotation Increases or Decreases value.
3.Function Key MENU Enter SYSTEM MENU
PANIC Panic recording at continuous mode at highest quality (120ips,
Highest, 1/1x)
BOOKMARK Check the bookmark while playback for bookmark search.
PLAY Playback recorded data on HDD
AUDIO Select audio channel. Turn volume up/down
KLOCK
Locking the key
K
.
LOCK
Locking
the
key
.
To unlock, keep pressing the button for a few seconds and
input password (Same password for Setup Menu)
SEARCH Search recorded data on HDD
STOP Stop Playback.
4.LIVE View
Control Key
PTZ Shift LIVE mode to PTZ control mode
MODE Switch screen division from full screen to 16 s
p
lit screen
(
in 1
,
p(,
4, 9, 13, 16 sequence )
SEQ Auto camera image sequence in full screen mode
PIP Picture In Picture mode
FRZ Freeze Live display
ZOOM Zoom image
6

Name Function
4-1.Control Key FUNC Main menu panel On/Off
ESC Cancel selected menu panel
+ Increase setting value, page shift
- Decrease setting value, page shift
5A k
Nitith
5
.
A
rrow
k
e
y
N
av
ig
a
t
e
i
n
th
e menu
6. USB Device For Firmware upgrade and USB backup
7.Camera Selection
/ PTZ Control
1~16 Button : Select camera channel in full screen mode
NEAR : FOCUS NEAR PRESET + : Increase PRESET NO.
FAR : FOCUS FAR PRESET - : Decrease PRESET NO.
WIDE : ZOOM IN PTZMENU : PTZ MENU POPUP
TELE : ZOOM OUT F1 : USER 1
SET : PRESET SET F2 : USER 2
CLEAR : PRESET CLEAR F3 : USER 3
GOTO : PRESET GOTO F4 : USER 4
AUTO : AUTO SCAN F5 : USER 5
8.CD/DVD-ROM For Firmware upgrade and CD/DVD backup
7

2-2. Rear
[Rear Panel for 4ch DVR]
257
11
13
4689 10 12
[Rear Panel for 8ch DVR]
25711
1
3
4
6
8
9
10
12
[Rear Panel for 16ch DVR]
1
3
4
6
8
9
10
12
1
234 57
10 11
8
68912

Name Function
1 RS 485 Connection with PTZ Camera or other external devices using RS 485
RELAY Output Relay Output terminal
SENSOR Input Sensor Input terminal
2 VGA VGA Output to CRT or TFT LCD Monitors
3 ETHERNET Connection to Ethernet devices
4 RS-232C Connection to external devices such as PC using RS-232C to control DVR
5 Camera Input Connection with NTSC/PAL Cameras
6 Loop Out Camera Loop out
7 Monitor Output Connection with NTSC/PAL Composite Monitor
8 SPOT Output Connection from Analog backup output to external devices
9 DC Power DC 12V 6.67A Adaptor
10 PS2 Mouse Connection to PS2 Mouse
11 Audio Microphone input and Audio output
12 POWER
SWITCH
Power ON/OFF Switch
NOTE : You can not mix PAL and NTSC equipment. For example, you cannot
use a PAL camera and NTSC monitor.
9

3. Installation
3-1. Configuration
[ Typical Digital Video Recorder Installation ]
10

3
2 Detailed Configuration
1
1) Rack mount
3
-
2
.
Detailed
Configuration
2
1
3
1. Remove all 4 bolts on side caps.
2. Attach Rack mount bracket to DVR.
3. Attach DVR with rack mount bracket to 19” Rack.
2) HDD (Hard Disk Drive) Connection
1. Connect Main Board and HDD1 using IDE cable and HDD power cable.
2. When you use just 1 HDD, install the HDD onto HDD1 location.
3. When you use 2 HDDs, install the first HDD onto HDD1 location and then install the second HDD
onto HDD2 location in order.
4. Stick the HDD absorber (included in package) on the bottom of case and then install the HDD
on to
p
of them b
y
usin
g
the bolts
(
included in
p
acka
g
e
)
.
pyg( pg)
5. Screws must be inserted from outside of the case bottom.
11

HDD Cable Connection HDD Fix
[4ch]
MAIN BOARD
xxxxxx
MAIN BOARD
HDD1 HDD2
xxxxxx
CD-RW
(MASTER)
HDD1
(MASTER
1) HDD2
(MASTER2)
[
8
ch]
HDD Cable Connection HDD Fix
MAIN BOARD
MAIN BOARD
HDD1 HDD2
[
8
ch]
xx
xx
xx
xx
xx
xx
CD-RW
(MASTER)
HDD1
(MASTER
1) HDD2
(MASTER2)
HDD Cable Connection HDD Fix
MAIN BOARD
MAIN BOARD
[16ch]
MAIN
BOARD
xx
xx
xx
xx
xx
xx
CD-RW
(MASTER)
HDD1
(MASTER
1) HDD2
(MASTER2)
HDD1 HDD2
12

3) Camera
VIDEO
LENS
VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear view of CAMERA
Connect cameras to the camera input on rear panel of DVR marked CAMERA IN.
4
)A di
4
)
A
u
di
o
- Audio Input
1. 4ch Audio Input is available for MSD-1600, 2ch for MSD-800, 1ch for MSD-400.
2. Connect Audio Input as needed for camera channels.
3. Audio channel 1 is assigned for camera channel 1~4, audio channel 2 for camera
channel 5~8 audio channel 3 for camera channel 9~12 and audio channel 4 for
channel
5~8
,
audio
channel
3
for
camera
channel
9~12
and
audio
channel
4
for
camera channel 13~16.
4. Audio input should be connected according to assigned camera channels for audio
recording.
- Microphone Input
1. 1 Microphone Input is available. It does not record microphone input.
2. Microphone is to support TWO-WAY Audio, for communication with remote user.
- Audio Output
1. 1ch Audio Output is available.
2. Selected Audio channel at DVR will be output.
13

5) Monitor
VIDEO A
IN OUT
VIDEO C
IN OUT
VIDEO B
IN OUT
Connect the video output marked MONITOR to VIDEO-IN of Main Monitor.
6) Power Cable
Connect DC 12V, 6.67A Adaptor to the back side
of Power Jack for right operation of 2HDDs and
CD Recorder.
Before turning on, be sure all necessary devices
such as Power adaptor, cameras and Monitor are
connected properly to DVR!
Notice
To avoid accidental deletion of HDD data, please make sure to press MENU button before
powering off the unit. This takes the unit out of recording mode for safe shutdown.
7) SPOT
Connection with the spot monitor as needed.
14

8) Others
[
4CH
]
[
]
SPEAKER
VGA
MONITOR
PC
PC
MIC
SENSOR
SIREN
PTZ
CAMERA
PAN/TILT
CAMERA
SIREN
[8CH]
SPEAKER
PC
MIC
VGA
MONITOR
PTZ
PAN
/
TILT
PC
SENSOR SIREN
PTZ
CAMERA
PAN
/
TILT
CAMERA
15

[16CH]
SPEAKER
VGA
MONITOR
PC
PC
MIC
SENSOR SIREN
PTZ
CAMERA
PAN/TILT
CAMERA
RS-232C : Control DVR through RS-232C port by using PC.
RS-485 : Control external device such as PTZ Cameras.
(Pin No.1 ~ 2 at Terminal Block).
RELAY Output : (Pin No.4 ~6 at Terminal Block).
SENSOR Input
:(PinNo8~11/No13~16
/
No 18 ~ 21
/
No 23 ~ 26
SENSOR
Input
:
(Pin
No
.
8
~
11
/
No
.
13
~
16
/
No
.
18
~
21
/
No
.
23
~
26
at Terminal Block).
GND : Ground (Pin No.3 / No.7 / No.12 / No.17 / No.22 at Terminal Block).
ETHERNET : Connection to LAN, WAN and Internet.
VGA : Connection to VGA Monitor (CRT, TFT LCD Monitor) is available if
optional VGA board is fixed on the main board.
Resolution is set to 800x600 60 Hz
User can change resolution in MONITOR SETUP / VGA SETUP /
VGA RESOLUTION.
16

4. Display Configuration
2
3
1
No Contents Description
1
Di l
Display Date/Time, HDD Status, HDD recorded space,available
1
Di
s
pl
a
y
remaining days, and audio channel
2Main Menu Click with mouse : SPLIT, CHANNEL, AUDIO, FRZ, SEQ, ZOOM, PIP,
PTZ, SETUP, PANIC, PLAY, SEARCH
3LIVE Live screen of each channel
Camera Title & Status
17

4
-
1
Display
4
1
.
Display
1) Date/Time
Live mode : shows the current date & time
Playback mode : shows the recorded date & time of the playback image
2
) AUDIO Icon
2
)
AUDIO
Icon
The number in the icon indicates which Audio channel is on.
In case Audio channel 1 is ON, appears.
3) Record Icon
4) HDD Overwrite
Displays the current recording mode.
In case of Continuous Recording Mode, appears.
appears when the HDD overwrite mode is selected.
5) HDD Space
The HDD recorded space is marked in red on the time bar.
The available remaining days/time at the current record mode is also displayed.
18

4-2. Main Menu
1) Split Screen
Screen division panels display various screen viewing options:
Full screen mode : Channel Bar pops up 9 Channels Split
4 Channels Split 16 Channels Split
2) Display Channel Selection
Display Channel Selection Panel views and selected channel displays in full screen mode
3) AUDIO Channel Selection
Display
Channel
Selection
Panel
views
,
and
selected
channel
displays
in
full
screen
mode
.
(Channels are also selectable in ZOOM, PTZ, and FREEZE mode.)
Audio Channel Selection Panel controls.
4) SEQ (Sequence)
Displays full screen mode images in sequence
(1ch output for 4ch DVR, 2ch output for 8ch DVR, 4ch output for 16ch DVR)
Displays
full
screen
mode
images
in
sequence
In case of 4 Split, 1,2,3,4 -> 5,6,7,8 -> 9,10,11,12…… images sequenced.
CH
04
CH
04
CH03
CH02
CH01
●
●
●
19

5
)FRZ
(Freeze)
6) PTZ (PAN/ TILT/ ZOOM)
5
)
FRZ
(Freeze)
Click FRZ to pause with
Click each channel to pause with
icon.
icon.
Click the PTZ button, and the PTZ Controller panel will pop up as shown below.
OPEN IRIS OPEN SET PRESET SET
CLOSE IRIS CLOSE CLEAR PRESET CLEAR
WIDE ZOOM OUT GOTO PRESET GO TO
TELE ZOOM IN AUTO AUTO SCAN
NEAR FOCUS NEAR Arrow PAN / TILT
FAR FOCUS FAR No. PRESET No.
7) ZOOM
In LIVE mode, images Zoom in X2.
Move selected frame by mouse control.
Click ESC to exit zoom mode.
8
)PIP
8
)
PIP
CAM01
CAM02
One channel displays on the full monitor screen while another
small screen displays on the inset window.
-Small screen can display in sequence according to preset interval.
- Full screen can be shifted to next channel by clicking the full
screen or by clicking the channel number.
20