iDataLink ADS-DLSL-CH1 User manual

VERSION FRANÇAISE DISPONIBLE EN LIGNE AU www.idatalink.com
PLEASE VISIT www.idatalink.com/support FOR COMPLETE PRODUCT DETAILS
Automotive Data Solutions Inc.
ADS-DLSL-CH1
INSTALL GUIDE CH1
VERSION FRANÇAISE DISPONIBLE EN LIGNE AU www.idatalink.com
PLEASE VISIT www.idatalink.com/support FOR COMPLETE PRODUCT DETAILS
The Chrysler, Jeep and Dodge logos are property of their respective owners.
© 2007 - Automotive Data Solutions Inc
DatedeRev.:17décembre2007
Num.deDoc.:##00130##

INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 2 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc. www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
to determine iF the Vehicle is eQuipped with
oem alarm, please Follow procedure on
page 8.
99 00 01 02 03 04 05 06 07
key Bypass *
o.e.m. alarm control
doorlocks
priority unlock
trunk release
leFt sliding door
right sliding door
door status
trunk status
tach output
second start
make model install type Features
CHRYSLER
300M 1 1 1 1 1 1 ••••• • •
300M w/ Alarm 3 3 3 3 3 3
Concorde 1 1 1 1 1 1 ••••• • •
Concorde w/ Alarm 3 3 3 3 3 3
Intrepid 1 1 1 1 1 1 ••••• • •
Intrepid w/ Alarm 3 3 3 3 3 3 ••••• • •
LHS 1 1 1 1 ••••• • •
LHS w/ Alarm 3 3 3 3 ••••• • •
Neon 3 3 3 3 3 3 ••••• • •
PT Cruiser 3333 ••••• •••
Sebring Sedan/Convertible 1 1 1 1 1 1 1 ••••• •••
Sebring Sedan/Convertible w/ Alarm 3 3 3 3 3 3 3 ••••• •••
Town & Country 4 4 4 ••••••••••Δ
DODGE
Caravan/Grand Caravan 4 4 4 ••••••••••Δ
Caravan/Grand Caravan w/ Alarm 5 5 5 ••••••••••Δ
Dakota 666 • • • • • •
Dakota w/ Alarm 333 • • • • • •
Durango 6 6 6 6 •••• •••
Durango w/ Alarm 3 3 3 3 •••• •••
Intrepid 1 1 1 1 1 1 ••••• • •
Intrepid w/ Alarm 3 3 3 3 3 3 ••••• • •
Neon 3 3 3 3 3 3 ••••• • •
Ram Pickup 1111 • • • • • •
Ram Pickup w/ Alarm 3333 • • • • • •
SRT 4 3 3 3 ••••• • •
Stratus Sedan 1 1 1 1 1 1 ••••• •••
Stratus Sedan w/Alarm 3 3 3 3 3 3 ••••• •••
SX 2.0 3 3 3 3 ••••• • •
JEEP Cherokee/Grand Cherokee 1 1 1 1 1 1 ••••• •••
Liberty 333 • • • • • •
VEHICLE COMPATIBILITY CHART
2. proceed with installation See applicable wiring diagram
NOTE : ensure all connections are completed and properly secured prior to connecting the wire harnesses to the module.
1. determine install type Refer to chart below
Num.deDoc.:##00130##

www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 3 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
161514131211109
87
654321
LOCK/ARM (-) INPUT - GREEN/BLACK
UNLOCK/DISARM (-) INPUT - BLUE/BLACK
TRUNK (-) INPUT - RED/WHITE
(NC) BROWN
(NC) PURPLE/YELLOW
(NC) PURPLE/BLACK
(NC) WHITE
(NC) BLACK/WHITE
DOOR & TRUNK STATUS (-) OUTPUT - GREEN
TACH OUTPUT (AC) - PURPLE/WHITE
BROWN/RED (NC)
BROWN/YELLOW (NC)
ORANGE/BLACK (NC)
ORANGE/WHITE (NC)
ORANGE - DATA (J1850)
PINK/BLACK (NC)
PINK - IGNITION (+) INPUT
YELLOW/BLACK (NC)
YELLOW/RED (NC)
YELLOW (NC)
GROUND-OUTPUT WHEN RUNNING (-) - BLUE/WHITE
(NC) WHITE
GROUND - BLACK
12V - RED
CONNECT TO PIN #2 OF OBDII
CONNECTOR LOCATED UNDER
DRIVER SIDE DASHBOARD
***** OPTIONAL *****
TRANSPONDER LOOP
ADS-RNG-C1 IS REQUIRED
FOR TRANSPONDER BYPASS
APPLICATION.
CONNECT EITHER
IDATALINK OR
STANDARD WIRING
IDATALINK
IDATALINK (RS232) PORT
REQUIRED ON REMOTE STARTER.
IF THE PORT IS UNAVAILABLE
USE STANDARD WIRING METHOD.
LEGEND
Wiring connections not required
when installed in iDataLink mode
REMOTE
STARTER
OR
SECURITY
SYSTEM
OR
KEYLESS
ENTRY
TYPE 1 WIRING DIAGRAM
Num.deDoc.:##00130##

INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 4 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
161514131211109
87
654321
LOCK/ARM (-) INPUT - GREEN/BLACK
UNLOCK/DISARM (-) INPUT - BLUE/BLACK
TRUNK (-) INPUT - RED/WHITE
(NC) BROWN
(NC) PURPLE/YELLOW
(NC) PURPLE/BLACK
(NC) WHITE
(NC) BLACK/WHITE
DOOR & TRUNK STATUS OUTPUT - GREEN
TACH OUTPUT (AC) - PURPLE/WHITE
BROWN/RED (NC)
BROWN/YELLOW (NC)
ORANGE/BLACK (NC)
ORANGE/WHITE (NC)
ORANGE - DATA (J1850)
PINK/BLACK (NC)
PINK - IGNITION (+) INPUT
YELLOW/BLACK (NC)
YELLOW/RED (NC)
YELLOW - ANALOG OUTPUT
GROUND-OUTPUT WHEN RUNNING (-) - BLUE/WHITE
(NC) NO WIRE
GROUND - BLACK
12V - RED
***** OPTIONAL *****
TRANSPONDER LOOP
ADS-RNG-C1 IS REQUIRED
FOR TRANSPONDER BYPASS
APPLICATION.
CONNECT EITHER
IDATALINK OR
STANDARD WIRING
IDATALINK
ANALOG CONTROL
PLEASE REFER TO WIRING
CROSS-REFERENCE CHART
TO IDENTIFY WIRE COLOR
AND LOCATION
IDATALINK (RS232) PORT
REQUIRED ON REMOTE STARTER.
IF THE PORT IS UNAVAILABLE
USE STANDARD WIRING METHOD.
LEGEND
Wiring connections not required
when installed in iDataLink mode
CONNECT TO PIN #2 OF OBDII
CONNECTOR LOCATED UNDER
DRIVER SIDE DASHBOARD
REMOTE
STARTER
OR
SECURITY
SYSTEM
OR
KEYLESS
ENTRY
TYPE 3 WIRING DIAGRAM AND CROSS-REFERENCE CHART
model years wire color location
300M 1999-2004 Light Green/Orange At BCM, C4 Connector, Pin #13 (See BCM image)
Concorde 1999-2004 Light Green/Orange At BCM, C4 Connector, Pin #13 (See BCM image)
Intrepid 1999-2004 Light Green/Orange At BCM, C4 Connector, Pin #13 (See BCM image)
LHS 1999-2002 Light Green/Orange At BCM, C4 Connector, Pin #13 (See BCM image)
Neon 2000-2005 Light Green Harness coming from driver door
PT Cruiser 2002-2005 White/Dark Green Harness coming from driver door
Sebring Convertible 2001-2006 Light Green/Orange At BCM, C4 Connector, Pin #4 or Harness from driver door
Sebring Sedan 2001-2006 Light Green/Orange At BCM, C4 Connector, Pin #4 or Harness from driver door
Dakota 2002-2004 Light Green/Orange Driver Kick Panel
Durango 2000-2003 Light Green/Orange Driver Kick Panel
Intrepid 1999-2004 Light Green/Orange At BCM, C4 Connector, Pin #13 (See BCM image)
Neon 2000-2005 Light Green Harness coming from driver door
Ram Pickup 2002-2003 Light Green/Orange Driver Kick Panel
Ram Pickup 2004-2005 Purlple/Light Blue Driver Kick Panel
SRT 4 2004-2006 Light Green Harness coming from driver door
Stratus Sedan 2001-2006 Light Green/Orange At BCM, C4 Connector, Pin #4 or Harness from driver door
SX 2.0 2003-2006 Light Green Harness coming from driver door
Liberty 2002-2004 Pink/Violet At BCM, Under Black Cover (Note: Two wires have the same color,
you will have to test the wire for doorlock fluctuations.)
BODY CONTROL MODULE
C1
C2
C3
C4
GREY COVERBLACK COVER
WHITE COVER
BCM: LIBERTY
BODY CONTROL MODULE
C1
C2
C3
C4
GREY COVERBLACK COVER
WHITE COVER
BCM: 300M, CONCORDE, INTREPID
Num.deDoc.:##00130##

www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 5 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
161514131211109
87
654321
BLUE (IGNITION +)
YELLOW (STARTER +)
VIOLET/BROWN (SWITCH MUX*)
KEY
LOCK (-) INPUT - GREEN/BLACK
UNLOCK (-) INPUT - BLUE/BLACK
TRUNK (-) INPUT - RED/WHITE
(NC) BROWN
LEFT SLIDING DOOR (-) INPUT - VIOLET/YELLOW
RIGHT SLIDING DOOR (-) INPUT - VIOLET/BLACK
(NC) WHITE
(NC) BLACK/WHITE
TRUNK & DOOR STATUS (-) OUTPUT - GREEN
TACH OUTPUT (AC) - VIOLET/WHITE
BROWN/RED (NC)
BROWN/YELLOW (NC)
ORANGE/BLACK - GROUND
ORANGE/WHITE (NC)
ORANGE - DATA (J1850)
PINK/BLACK (NC)
PINK - IGNITION (+) INPUT
YELLOW/BLACK (NC)
YELLOW/RED (NC)
YELLOW - ANALOG OUTPUT
VIOLET/GREEN
GROUND-OUT WHEN RUNNING (-) - BLUE/WHITE
(NC) WHITE
GROUND - BLACK
12V - RED
REMOTE
STARTER
OR
SECURITY
SYSTEM
OR
KEYLESS
ENTRY
*Use isolated ground-out
when running from remote
starter to power relay.
RESISTOR
BETWEEN 180-210 0HMS
85
30
87
87A
86
***** OPTIONAL *****
TRANSPONDER LOOP
ADS-RNG-C1 IS REQUIRED
FOR TRANSPONDER BYPASS
APPLICATION.
CONNECT TO PIN #2 OF OBDII
CONNECTOR LOCATED UNDER
DRIVER SIDE DASHBOARD
BCM IS LOCATED UNDER DRIVER’S SIDE
DASH AGAINST FIREWALL.
IDATALINK (RS232) PORT
REQUIRED ON REMOTE STARTER.
IF THE PORT IS UNAVAILABLE
USE STANDARD WIRING METHOD.
LEGEND
Wiring connections not required
when installed in iDataLink mode
IDATALINK
CONNECT EITHER
IDATALINK OR
STANDARD WIRING
C1 C2 C3 C4 C5
1 9
26 34
C3
TYPE 4 WIRING DIAGRAM
Num.deDoc.:##00130##

INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 6 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
C1 C2 C3 C4 C5
1 9
26 34
C3
IDATALINK (RS232) PORT
REQUIRED ON REMOTE STARTER.
IF THE PORT IS UNAVAILABLE
USE STANDARD WIRING METHOD.
LEGEND
Wiring connections not required
when installed in iDataLink mode
IDATALINK
161514131211109
87
654321
BLUE (IGNITION +)
YELLOW (STARTER +)
VIOLET/BROWN (SWITCH MUX*)
KEY
LOCK (-) INPUT - GREEN/BLACK
UNLOCK (-) INPUT - BLUE/BLACK
TRUNK (-) INPUT - RED/WHITE
(NC) BROWN
LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW
RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK
(NC) WHITE
(NC) BLACK/WHITE
DOOR & TRUNK STATUS (-) OUTPUT - GREEN
TACH OUTPUT (AC) - PURPLE/WHITE
BROWN/RED (NC)
BROWN/YELLOW (NC)
ORANGE/BLACK (NC)
ORANGE/WHITE (NC)
ORANGE - DATA (J1850)
PINK/BLACK (NC)
PINK - IGNITION (+) INPUT
YELLOW/BLACK (NC)
YELLOW/RED (NC)
YELLOW - ANALOG OUTPUT
PURPLE/BLUE
GROUND-OUTPUT WHEN RUNNING (-)
BLUE/WHITE
(NC) WHITE
GROUND - BLACK
12V - RED
*use isolated ground-out
when running from remote
starter to power relay
RESISTOR
BETWEEN 180-210 0HMS
85
30
87
87A
86
***** OPTIONAL *****
TRANSPONDER LOOP
ADS-RNG-C1 IS REQUIRED
FOR TRANSPONDER BYPASS
APPLICATION.
CONNECT TO PIN #2 OF OBDII
CONNECTOR LOCATED UNDER
DRIVER SIDE DASHBOARD
BCM IS LOCATED UNDER DRIVER’S SIDE
DASH AGAINST FIREWALL.
CONNECT EITHER
IDATALINK OR
STANDARD WIRING
REMOTE
STARTER
OR
SECURITY
SYSTEM
OR
KEYLESS
ENTRY
TYPE 5 WIRING DIAGRAM
Num.deDoc.:##00130##

www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 7 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
161514131211109
87
654321
LOCK (-) INPUT - GREEN/BLACK
UNLOCK (-) INPUT - BLUE/BLACK
(NC) RED/WHITE
(NC) BROWN
(NC) PURPLE/YELLOW
(NC) PURPLE/BLACK
(NC) WHITE
(NC) BLACK/WHITE
DOOR & TRUNK STATUS (-) OUTPUT - GREEN
TACH OUTPUT (AC) - PURPLE/WHITE
BROWN/RED - GROUND
BROWN/YELLOW - KEYSENSE(-) OUTPUT
ORANGE/BLACK (NC)
ORANGE/WHITE (NC)
ORANGE - DATA (J1850)
PINK/BLACK (NC)
PINK - IGNITION (+) INPUT
YELLOW/BLACK (NC)
YELLOW/RED (NC)
YELLOW (NC)
BLUE/WHITE
(NC) NO WIRE
GROUND - BLACK
12V - RED
CONNECT TO PIN #2 OF OBDII
CONNECTOR LOCATED UNDER
DRIVER SIDE DASHBOARD
***** OPTIONAL *****
TRANSPONDER LOOP
ADS-RNG-C1 IS REQUIRED
FOR TRANSPONDER BYPASS
APPLICATION.
LIGHT BLUE (KEYSENSE)
IDATALINK (RS232) PORT
REQUIRED ON REMOTE STARTER.
IF THE PORT IS UNAVAILABLE
USE STANDARD WIRING METHOD.
LEGEND
Wiring connections not required
when installed in iDataLink mode
IDATALINK
CONNECT EITHER
IDATALINK OR
STANDARD WIRING
GROUND-OUTPUT WHEN RUNNING (-)
REMOTE
STARTER
OR
SECURITY
SYSTEM
OR
KEYLESS
ENTRY
TYPE 6 WIRING DIAGRAM
TO DETERMINE IF VEHICLE IS EQUIPPED WITH OEM ALARM
PROCEDURE wITH OEM KEYFOB
1. CLOSE hatch and hood.
2. CLOSE all doors and SIT at the driver seat.
3. PRESS lock on the OEM KEYFOB twice.
4. WAIT 60 seconds.
5. OPEN the driver’s door. If the alarm goes off, the vehicle is
equipped with an OEM alarm.
PROCEDURE WITHOUT OEM KEYFOB
1. OPEN driver’s door window.
2. CLOSE hatch and hood.
3. CLOSE all doors including driver’s door
4. LOCK the driver’s door twice using the key in driver’s door
key cylinder.
5. WAIT 60 seconds.
6. OPEN the driver’s door using the inside door handle by passing
your arm thru the opened window. If the alarm goes off, the ve-
hicle is equipped with an OEM alarm.
Num.deDoc.:##00130##

INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 8 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
1
2 3
Locate the Immobilizer security light. It is either a round red indicator in the cluster or a red led on top of the dashboard.
Locate the transponder on the antenna. Fold the harness as shown below.
TRANSPONDER PRE-PROGRAMMING
20
40
60
80
100 120
LOCATE
THE SECURITY LIGHT
1
3
Wait approximately 15 seconds
for security light to flash, indicating
you have accessed “Learning mode”.
A warning chime will also be heard.
Turn the ignition to the “OFF” position
and remove key from ignition.
Hold the transponder to the ignition
cylinder and power the main ignition
using a 10 Amp fused test lead.
(Note: If you encounter power loss
during this step, you will need to exit
learning mode and restart transponder
programming from step 1.
The security light will start flashing,
indicating you are now in programming
mode.
DO NOT INTERRUPT IGNITION until the
security light stops flashing.
Insert the first vehicle key into the ignition.
Turn the ignition to the “ON” position.
Security light on cluster will illuminate.
Once, the security light turns off,
turn the ignition to the “OFF” position
and remove key from ignition cylinder.
TRANSPONDER PROGRAMMING
ON
2Insert the second vehicle key into the
ignition. Turn the ignition to the “ON”
position.
Security light will illuminate
and then turn off.
The security light will turn on solid and
then turn off. The chime will be heard
once again.
Transponder programming is now
completed.
ON
2nd KEY
OFF
OFF
IMPORTANT: Both keys are required to complete the
programming procedure. A maximum of 5 second delay
between each step is permitted. If the delay is exceeded, the
vehicle will not allow programming to continue.
20
40
60
80
100 120
SECURITY LIGHT
ON THEN OFF
SECURITY LIGHT OFF
FLASHES
FLASHES
SOLID THEN OFF
HOLD TO CYLINDER
12V
IGNITION
10 AMPS
PROGRAMMING PROCEDURE
3. program your module See instructions on the following pages
IMPORTANT NOTICE
Chrysler’s Immobilizer modules will accept a maximum of 4 programmed
keys. If the vehicle already has 4 keys programmed, it will be impossible
to learn the transponder unless a new Immobilizer module is installed in
the vehicle and programmed to recognize the vehicle ID by the new car
dealer.
Programming will require access to TWO valid vehicle keys. These keys will
be returned to the vehicle owner once the installation has been completed.
note: The transponder is compatible with the Chrysler Durango 2004
vehicle. However, all Durango’s built prior to 5/17/04 must get a WCM
module upgrade which will correct a problem preventing the vehicle from
learning additional keys. Chrysler is correcting this issue only when a
Durango owner requests a new transponder key.
The transponder must be programmed as would an additional key.
The WCM replacement part number is 56038675AS.
Num.deDoc.:##00130##

www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 9 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
1
2 3
Locate the Immobilizer security light. It is either a round red indicator in the cluster or a red led on top of the dashboard.
Locate the transponder on the antenna. Fold the harness as shown below.
TRANSPONDER PRE-PROGRAMMING
20
40
60
80
100 120
LOCATE
THE SECURITY LIGHT
1
3
Wait approximately 15 seconds
for security light to flash, indicating
you have accessed “Learning mode”.
A warning chime will also be heard.
Turn the ignition to the “OFF” position
and remove key from ignition.
Hold the transponder to the ignition
cylinder and power the main ignition
using a 10 Amp fused test lead.
(Note: If you encounter power loss
during this step, you will need to exit
learning mode and restart transponder
programming from step 1.
The security light will start flashing,
indicating you are now in programming
mode.
DO NOT INTERRUPT IGNITION until the
security light stops flashing.
Insert the first vehicle key into the ignition.
Turn the ignition to the “ON” position.
Security light on cluster will illuminate.
Once, the security light turns off,
turn the ignition to the “OFF” position
and remove key from ignition cylinder.
TRANSPONDER PROGRAMMING
ON
2Insert the second vehicle key into the
ignition. Turn the ignition to the “ON”
position.
Security light will illuminate
and then turn off.
The security light will turn on solid and
then turn off. The chime will be heard
once again.
Transponder programming is now
completed.
ON
2nd KEY
OFF
OFF
IMPORTANT: Both keys are required to complete the
programming procedure. A maximum of 5 second delay
between each step is permitted. If the delay is exceeded, the
vehicle will not allow programming to continue.
20
40
60
80
100 120
SECURITY LIGHT
ON THEN OFF
SECURITY LIGHT OFF
FLASHES
FLASHES
SOLID THEN OFF
HOLD TO CYLINDER
12V
IGNITION
10 AMPS
PROGRAMMING PROCEDURE
Num.deDoc.:##00130##

INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 10 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
12
Insert the vehicle key into the ignition.
Turn the ignition to the “ON” position.
Wait for the LED to illuminate green
for 2 SECONDS.
Programming is complete.
VEHICLE PROGRAMMING
ON
LED “ON” 2 SEC
12
NOTE
MODE SELECTION
1X 2X
PRESS
TO TOGGLE
BETWEEN MODES PRESS + HOLD
Should you wish to change the installation mode,
follow the “Factory Reset” instructions as detailed below.
Press and release the programming button to select installation mode. To register selection,
Hold the programming button down
until the LED displays a solid green light.
OR
IDATALINK MODE STANDARD MODE
LED flashes once LED flashes twice
REMOTE STARTER
with Data Port
REMOTE STARTER
without Data Port
1
2
Wrap the loop tightly around the key cylinder 3 to 5 times.
Slide the plastic retainer up towards the cylinder to tighten the noose.
NOTE: It is preferable to place the antenna loop on top or in front of the OEM immobilizer coil.
Connect antenna to the blue connector on iDatalink Module.
NOTE: KEEP TRANSPONDER AWAY FROM ANY METAL SOURCE OR WIRING.
ANTENNA INSTALLATION INSTRUCTIONS
OR NOT
Num.deDoc.:##00130##

www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
INSTALL GUIDE
Version française disponible en ligne au www.idatalink.com
Doorlock Interface
chrysler/dodge/Jeep
Page 11 of 11 ADS-DLSL-CH1 20071214
www.idatalink.com For technical assistance, contact your distributor or visit www.idatalink.com/support © 2007 ADS Inc.
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
GREEN
CORRECTLY
PROGRAMMED
RED
INCORRECTLY
PROGRAMMED
1
3 4
2
DIAGNOSTICS
FACTORY RESET PROCEDURE
HOLD
When the remote starter is engaged, the LED will flash green to indicate the module
has been correctly programmed. If the LED remains illuminated red, the device is
incorretly programmed.
Unplug all connectors from the module. Press and hold the programming button while inserting either
the 4-PIN standard or 4-PIN optional iDatalink connector.
The LED will begin to flash red. Immediately release the programming button.
The LED will turn on solid red for 2 seconds to confirm module reset.
Once reset is confirmed, plug in remaining connections and
REPEAT PROGRAMMING PROCEDURE
INSERT
4 PIN CONNECTOR
UNPLUG CONNECTORS
WHEN LED FLASHES RED
RELEASE THE BUTTON
SOLID RED LED
CONFIRMS FACTORY RESET
Num.deDoc.:##00130##
Table of contents
Other iDataLink Car Alarm manuals

iDataLink
iDataLink COM-AL(RS)-TL2-EN User manual

iDataLink
iDataLink ADS-AL(DL)-HA1-EN User manual

iDataLink
iDataLink ADS-DL-CH6 User manual

iDataLink
iDataLink ADS-TBSL-PL User manual

iDataLink
iDataLink ADS-AL(DL)-SUB2-EN User manual

iDataLink
iDataLink maestro Rr User manual

iDataLink
iDataLink maestro Rr User manual