IDE e1.01 User manual

Part I Installation
Part II Operating manual
1. Operating mode ........................................................................... 4
2. Programming mode ...................................................................... 5
2.1. Default session time ............................................................ 5
2.2. Time delay........................................................................... 6
2.3. Advanced functions ............................................................. 6
2.3.1. Counters presentation ............................................... 7
2.3.2. Protected settings ..................................................... 7
2.3.2.1. Counters .......................................................... 8
Lamps counter 1 ..................................................... 9
Lamps counter 2 ..................................................... 9
Lamps counter 3 ................................................... 10
Fans counter ........................................................ 10
Time delays counter ..............................................11
Paid time counter .................................................. 11
Clients counter ..................................................... 12
2.3.2.2. Statistics ........................................................ 12
Electric energy counter ......................................... 12
Takings total counter ............................................ 13
2.3.2.3. Programming options ..................................... 14
Step ..................................................................... 14
Maximum time delay ............................................ 15
Maximum session time ......................................... 15
Ventilation ............................................................ 16
Price .................................................................... 16
Lamps end ........................................................... 17
Lamps power consumption .................................. 17
Fans power consumption ..................................... 18
Stop fans .............................................................. 18
Stop lamps ........................................................... 19
External stop ........................................................ 19
Buzzer ................................................................. 20
2.3.2.4. No code access .............................................. 20
2.3.2.5. Code change ................................................. 21
Part I is designed for the technician. It contains information about
electrical connections and I.D.E. e1.01 controller installation.
Part II is designed for the user. It contains information about menu
configuration and operating cycle.
Table of contents
START
STOP
T
START
Symbols used in the manual
I.D.E. e1.01 sunbed controller
I.D.E. Systemy Elektroniczne 1PageVersion 1.1 07/2005
MENU
STOP buttons in the
controller
buttons inside sunbed
procceds automatically
with the time passage
ATTENTION!
EN

The installation of the I.D.E. e1.01 controller should be
conducted by the authorized service. The producer does not take
any responsibility for any damage or loss resulted from the
installation conducted by the unauthorized service.
Disconnect power supply in the sunbed before
installation.
These
connections provide power supply for the controller and enable
operations on the lamps and fans operation control circuits. Connect
the following wires to the sunbed.
lamps operation control circuit
the phase supplying the control
circuits of the tanning device
operation control circuit
If the sunbed is equipped with the system of
automatic ventilation, fans operation control circuit
should not be connected. Insulate the red cable
properly.
If the sunbed is equipped with the system of automatic
ventilation,
These
include the connection of and buttons in the sunbed,
operating as normally opened contactors. Connect the following wires
to the sunbed.
if
not connected to the sunbed, should be properly
insulated.
Read the sunbed manual to choose the optimal type of
connection before preparing electrical connections:
Type A - lamps and/or fans operation control circuit connection
(230 V,AC);
Type B - potential free contact connections.
Electrical connection - TypeA
1. Prepare the following circuit connections (picture 2).
yellow wire - (230 V,AC);
black wire - 230 V, AC (
);
blue wire - neutral (N);
red wire - fans (230 V,AC)
ventilation time, set in the controller menu,
should be identical with the ventilation time, set inside
sunbed.
2. Prepare the following low voltage connections (picture 3).
white wire - 0 V;
sky blue wire - external button (remote start, quick
start);
white wire - 0 V;
orange wire - external button (remote stop, quick
stop).
Some sunbeds do not have “remote start” and/or
“remote stop” option. Read the sunbed manual
before preparing low voltage connections. Wires,
START STOP
START
STOP
I.D.E. Systemy Elektroniczne 2Version 1.1 07/2005 Page
Picture 3. Low voltage connections
Sunbed
button
STOP
button
START
Picture 2. Circuit connections- Type A
lamps operation control
circuit (230 V, AC)
Sunbed
fans operation control
circuit (230 V, AC)
phase (230 V, AC)
neutral (N)
Part I Installation
ID
e1.01
STOP MENU
STARTSTART
Picture 1. I.D.E. e1.01 controller
Sunbed
EN
I.D.E. e1.01 sunbed controller

In case of sunbeds with single button, orange
wire should not be connected (picture 4).
Electrical connection - Type B
Remove 5A fuse from the power supply and
operation device before preparing electrical
connections (picture 6). Removing 5A fuse allows to
prepare potentiel free contact connections.
1. Prepare the following circuit connections (picture 7).
black wire - (230 V,AC);
blue wire - neutral (N).
2. Prepare the following potential free contact connections (picture 8).
yellow wire - potential free contact;
red wire - potential free contact.
3. Prepare the following low voltage connections (picture 3).
white wire - 0 V;
sky blue wire - external button (remote start, quick
start);
white wire - 0 V;
orange wire - external button (remote stop, quick
stop).
Some sunbeds do not have “remote start” and/or
“remote stop” option. Read the sunbed manual
before preparing low voltage connections. Wires,
In case of sunbeds with single button, orange
wire should not be connected (picture 4).
After the above connections have been made, fasten the I.D.E. e1.01
control panel and connect it to the power supply and operation device
with the DB09 plug (picture 5).
These
connections provide power supply for the controller. Connect the
following wires to the sunbed.
phase
These connections enable operations on the sunbed.
These
include the connection of and buttons in the sunbed,
operating as normally opened contactors. Connect the following wires
to the sunbed.
if
not connected to the sunbed, should be properly
insulated.
After the above connections have been made, fasten the I.D.E. e1.01
control panel and connect it to the power supply and operation device
with the DB09 plug (picture 5).
START/STOP
START STOP
START
STOP
START/STOP
DB09
Fuse 100mA
Fuse 5A
I.D.E. Systemy Elektroniczne 3Version 1.1 07/2005 Page
Part I Installation
EN
Picture 4. Low voltage connections (single button)
START/STOP
Picture 5. I.D.E. e1.01 control panel - power supply and
operation device connection
Picture 6. 5A fuse
Picture 7. Power supply connection - Type B
phase
Sunbed
neutral (N)
Picture 8. P - Type Botential free contact connections
potential free contact
Sunbed
potential free contact
I.D.E. e1.01 sunbed controller
Sunbed
button
START/STOP

To turn on sunbed:
1.
2.
3. Press button in the controller. The controller starts counting
down time delay (Time delay, see page 6).
If lamps counter 3 contents exceeds Lamps end setting
(see page 17). the controller during the session signals
with sound signal the necessity of changing lamps.
If time delay set value is “zero”, lamps and fans will be
turned on after pressing button in the controller.
4.
.
If External stop option is activated (see page 19), there is
a possibility
If Stop lamps option is activated (see page 19), there is a
possibility
5.
and starts counting down ventilation time.
If Stop fans option is activated (see page 18), there is
a possibility
6.
When the controller is on standby, press button. Default session
time (see page 5) will be displayed.
Set the session time with and buttons.
During the time delay there
is a possibility of turning on the sunbed with button in the controller
or with button in the sunbed.
After the passage of the time delay, pressing button in the
controller, or pressing button in the sunbed, the controller turns
on lamps and fans and starts counting down session time
of turning off the lamps for a while with
button in the sunbed (session symbol will start blinking)
and restarting them with button.
of turning off the lamps (end of session) with
button in the controller.
After the passage of the session time, the controller turns off the
lamps
of turning off the fans (end of ventilation)
with button in the controller.
After the passage of the ventilation time, the controller passes to the
standby mode. The controller is ready to resume the sunbed or to
enter changes in the controller’s menu.
START
START
START
START
START
START
START
STOP
START
STOP
STOP
Part II Operating manual
1. Operating mode
START
STOP
START INFO
T
INFO
STOP START
T
STOP
START STOP
START/STOP
START
STOP
START INFO STOP
MENU
START INFO
STOP
STOP
MENU
i
START
INFO STOP
MENU
START
START
T
START
START
INFO
T
INFO
T
STOP
MENU
T
STOP
MENU
T
START
START STOP
MENU
T
START
START
STOP
MENU
START
STOP
MENU
START STOP
START STOP
T
STARTSTART
T
START
START
P
START
STOP
STOP
T
STOP
T
STOP
STOP
STOP
STOP
P
I.D.E. Systemy Elektroniczne 4PageVersion 1.1 07/2005
I.D.E. e1.01 sunbed controller EN

Changes in the controller’s menu settings are executed in the
programming mode. Controller’s main menu is protected by the code,
which prevents from entering the unauthorized changes.
After the changes have been entered in the controller’s
menu, it is necessary to leave the menu with button,
to save the changes in the long term memory. The
controller returns to the standby mode automatically,
saving all the changes in the long term memory, when
non active for more than 60 seconds.
Default session time option is used is to set the most frequent
operation time of the given sunbed. Default session time is used in the
operating mode (see page 4).
The
tanning symbol and the default session time setting is displayed
alternately.
efault session time setting
will be displayed
There are
two options in the main menu:
Default session time (see page 5);
Time delay (see page 6);
and Advanced functions submenu (see page 6).
To access programming mode, press button in the controller on
standby. Default session time will be displayed(see page 6).
Buttons functions in the programming mode
- “step forward”. Button is used to enter submenu, start editing
particular options and counters, and to confirm changes in the
temporary memory;
- “step backward”. Button is used for leaving submenu and leaving
the edited option or counter, and to confirm changes in the temporary
memory;
- buttons are used to change the parameters values and to
select particular option or submenu.
- button is active only on standby. It is used for entering and leaving
controller’s menu and saving changes in the long term memory.
2.1. Default session time
Range of setting: < 01.00 ; 60.00 > (min)
Default setting: 02.00
Step: <01.00 ; 10.00 > (min) - see page 14
To browse and/or change default session time:
1. When the controller is in the programming mode (see page 5),
select Default session time option with buttons.
2. To change the setting, press button. D
.
3. Set new value with buttons.
and
and
and
MENU
START
STOP
MENU
MENU
START
Part II Operating manual
2. Programming mode
I.D.E. Systemy Elektroniczne 5
P
START
STARTSTOP
P
MENU
I.D.E. e1.01 sunbed controller EN
PageVersion 1.1 07/2005
START STOP
P

4. To save new setting in the temporary memory, press or
buttons.
To leave the programming mode and save new setting in the long term
memory, press button or wait 60 seconds.
2.2. Time delay
Range of setting: < 00.00 ; 60.00 > (min)
Default setting: 01.00
Step: 15 sec
If time delay set value is “zero”, lamps and fans will be
turned on after pressing button in the controller.
To browse and/or change time delay:
1. When the controller is in the programming mode (see page 5),
select Time delay option with buttons.
2. To change the setting, press button. Time delay setting
.
3. Set new value with buttons.
4. To save new setting in the temporary memory, press or
buttons.
To leave the programming mode and save new setting in the long term
memory, press button or wait 60 seconds.
2.3. Advanced functions
There are two submenus in the Advanced functions submenu:
Protected settings, which access to requires entering the code; and
Counters presentation.
To access Advanced functions submenu:
1. When the controller is in the programming mode (see page 5),
select Advanced functions submenu with buttons.
2. Press button. Counters presentation submenu will be
displayed.
To leave the programming mode, press button or wait 60 seconds.
Time delay is the time necessary for the client to prepare for session.
The time delay is counted down from the moment of pressing
button in the controller, confirming the set session time. During the
time delay it is possible to turn on the lamps with in the controller or
button in the sunbed. After the passage of the time delay, the
sunbed turns on automatically.
The time delay
symbol and the time delay setting is displayed alternately.
will be
displayed
and
and
and
START STOP
MENU
START
START
START
START
START
START STOP
MENU
START
MENU
P
START
STARTSTOP
START STOP
P
START STOP
I.D.E. Systemy Elektroniczne 6
I.D.E. e1.01 sunbed controller EN
PageVersion 1.1 07/2005
Part II Operating manual
2. Programming mode

2.3.1. Counters presentation
The controller has 9 counters. In the Counters presentation submenu
it is only possible to browse the contents of the following counters:
Lamps counter 1 (see page 9);
Lamps counter 2 (see page 9);
Lamps counter 3 (see page 10);
(see page 10);
(see page 11);
Paid time counter (see page 11);
Clients counter (see page 12);
Electric energy counter (see page 12);
Takings total counter (see page 13).
In the Counters presentation submenu it is possible to
browse the counters, which were activated in the No
code access submenu (see page 20).
All counters are also available in the Counters submenu
(see page 8) and Statistics submenu (see page 12). In
these submenus it is possible to browse and delete
counters contents.
To browse the contents of the accessible counters:
1. When the controller is in the programming mode (see page 5), in the
Counters presentation submenu, select accessible counter with
buttons.
2. Press button.
To return to the Advanced functions submenu (see page 6), press
button. To leave the programming mode, press button or wait 60
seconds.
Step 2. does not apply to clients counter, electric
energy counter and takings total counter.
2.3.2. Protected settings
There are 5 submeuns in the Protected settings submenu, which
access to requires entering the code:
Counters (see page 8);
Statistics (see page 12);
Programming options (see page 14)
No code access (see page 20);
Code change (see page 21).
All new controllers have producer’s code (00000), which should be
changed by the sunbed owner (Code change, see page 21), which
prevents
Fans counter
Time delays counter
and The selected counter symbol and its contents is
displayed alternately.
The selected counter symbol and its contents,
expressed in minutes, is displayed alternately.
from entering the unauthorized changes in the controller’s
menu.
START
STOP
MENU
I.D.E. Systemy Elektroniczne 7
START STOP
P
P
P
P
P
P
P
P
P
I.D.E. e1.01 sunbed controller EN
PageVersion 1.1 07/2005
Part II Operating manual
2. Programming mode

To access Protected setings submenu:
1. When the controller is in the programming mode (see page 5), in the
Advanced functions submenu (see page 6), select Protected settings
submenu with buttons.
2. Press button. Enter the code with buttons,
confirming each number with button.
To return to the Advanced functions submenu, press button. To
leave the programming mode, press button or wait 60 seconds.
2.3.2.1. Counters
In the Counters submenu (see page 8) it is possible to browse and
delete the following counters:
Lamps counter 1 (see page 9);
Lamps counter 2 (see page 9);
Lamps counter 3 (see page 10);
Fans counter (see page 10);
Time delays counter (see page 11);
Paid time counter (see page 11);
Clients counter (see page 12).
To access Counters submenu:
1. When the controller is in the programming mode (see page 5), in the
Protected settings submenu (see page 7), select Counters submenu
with buttons.
2. Press button.
To return to the Protected settings submenu, press button. To
leave the programming mode, press button or wait 60 seconds.
and
and
and
If the entered code is proper, Counters submenu will be
displayed (see page 8). If the entered code is wrong,
will be displayed for a while. In such a case it is
necessarily to repeat entering the code.
START
START
STOP
MENU
START
STOP
MENU
START STOP
START
STOP
T
STOP
START STOP
I.D.E. Systemy Elektroniczne 8
I.D.E. e1.01 sunbed controller EN
PageVersion 1.1 07/2005
Part II Operating manual
2. Programming mode

Lamps counter 1
Lamps counter 1 (undeletable) shows real lamps operation time since
the installation.
Counter’s capacity: <0000h00m ; 9999h59m >
Default setting: 0000h00m
To browse lamps counter 1 contents:
1. When the controller is in the programming mode (see page 5), in the
Counters submenu (see page 8), select lamps counter 1 with
buttons. Lamps counter 1
2. Press button. Lamps counter 1
To return to the Counters submenu, press button. To leave the
programming mode, press button or wait 60 seconds.
Lamps counter 2
Lamps counter 2 (deletable) shows real lamps operation time since
the last deleting.
Counter’s capacity: <0000h00m ; 9999h59m >
Default setting: 0000h00m
To browse and/or delete lamps counter 2 contents:
1. When the controller is in the programming mode (see page 5), in the
Counters submenu (see page 8), select lamps counter 2 with
buttons. Lamps counter 2
2. Press button. Lamps counter 2
3. To delete lamps counter 2 contents, press button.
4. To delete lamps counter 2 contents, press button. To stop
deleting counter’s contents, press button.
To return to the Counters submenu, press button. To leave the
programming mode, press button or wait 60 seconds.
and
and
symbol and its contents, expressed in
hours, is displayed alternately.
symbol and its contents,
expressed in minutes, is displayed alternately.
The changes of the counter’s contents are saved
automatically in the long term memory after each minute,
during the session.
symbol and its contents, expressed in
hours, is displayed alternately.
symbol and its contents,
expressed in minutes, is displayed alternately.
The changes of the counter’s contents are saved
automatically in the long term memory after each minute,
during the session.
START
STOP
MENU
START
START
STOP
STOP
MENU
P
P
P
START
STOP
START STOP
P
P
START STOP
I.D.E. Systemy Elektroniczne 9
P
I.D.E. e1.01 sunbed controller EN
PageVersion 1.1 07/2005
Part II Operating manual
2. Programming mode

P
P
START STOP
I.D.E. Systemy Elektroniczne 10
Lamps counter 3
Lamps counter 3 (deletable) shows real lamps operation time since
the last deleting.
Counter’s capacity: <0000h00m ; 9999h59m >
Default setting: 0000h00m
To browse and/or delete lamps counter 3 contents:
1. When the controller is in the programming mode (see page 5), in the
Counters submenu (see page 8), select lamps counter 3 with
buttons. Lamps counter 3
2. Press button. Lamps counter 3
3. To delete lamps counter 3 contents, press button.
4. To delete lamps counter 3 contents, press button. To stop
deleting counter’s contents, press button.
To return to the Counters submenu, press button. To leave the
programming mode, press button or wait 60 seconds.
Fans counter
Fans counter (deletable) shows real fans operation time since the last
deleting.
Counter’s capacity: <0000h00m ; 9999h59m >
Default setting: 0000h00m
To browse and/or delete fans counter contents:
1. When the controller is in the programming mode (see page 5), in the
Counters submenu (see page 8), select fans counter with
buttons. Fans counter
2. Press button. Fans counter
3. To delete fans counter contents, press button.
4. To delete fans counter contents, press button. To stop deleting
counter’s contents, press button.
To return to the Counters submenu, press button. To leave the
programming mode, press button or wait 60 seconds.
and
and
symbol and its contents, expressed in
hours, is displayed alternately.
symbol and its contents,
expressed in minutes, is displayed alternately.
The changes of the counter’s contents are saved
automatically in the long term memory after each minute,
during the session.
symbol and its contents, expressed in hours, is
displayed alternately.
symbol and its contents, expressed
in minutes, is displayed alternately.
The changes of the counter’s contents are saved
automatically in the long term memory after each minute,
during the session.
START
START
STOP
STOP
MENU
START
START
STOP
STOP
MENU
P
START
P
STOP
P
P
P
START
START STOP
P
STOP
I.D.E. e1.01 sunbed controller EN
PageVersion 1.1 07/2005
Part II Operating manual
2. Programming mode