idea led POINTE-12R User manual

Order Code: POINTE-12R
User Manual
All the products' information accord to the actual li htin s' collocation. We will not
inform else if any chan e. We reserve the final interpretation ri ht.
Professional Movin Head Beam Spot Wash 3in1
POINTE-12R

Professional Moving Head Beam Troubleshooting
3.1 Control Panel
3.2 DMX Control
Professional Moving Head Beam Fixture Cleaning
4. Troubleshootin
5. Fixture Cleanin
● Clean with soft cloth usin normal lass cleanin fluid.
●Always dry the parts carefully.
5
The cleanin of internal and external optical lenses and/or mirrors must be carried
out periodically to optimize li ht output. Cleanin frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surroundin can cause reater accumulation of dirt on the unit’s optics.
●Clean the external optics at least every 20 days. Clean the internal optics at
least every 30/60 days.
Contents
1. Safety Instruction
Following are a few common problems that may occur during operation
Here are some suggestions for easy troubleshooting:
A The unit does no work, no light
1. Check the connect power and mains fuse.
2. Measure the mains volta e on the main connector.
B Not responding to DMX controller
1. Check DMX connectors, cables to see if they are linked properly.
2. Check the address settin s and DMX polarity.
3. If you have intermittent DMX si nal problems, check the pins on the connectors
or on PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check to see if the DMX cable run near or run alon side to hi h volta e cables
that may cause dama e or interference to DMX interface circuit.
2. Technical Specfication
3. How to Control the Packa e
3.2.1 DMX 512 Confi uration
3.2.2 DMX 512 Connection

Professional Moving Head Beam DMX 512 Connection Professional Moving Head Beam Safety
Safety Instructions:
Every person involved with the installation, operation and maintenance should:
A001 A017 A033 A049 ● Be competent
A001 A025 A049 A073 ● Follow the instructions of this user manual
Make sure there are not flammable materials close to the unit while operatin
Dama es caused by user modifications to the unit are not subject to warranty.
4 1
Termination reduces si nal errors and to avoid si nal transmission problems and
interference. It is always advisable to connect a DMX terminal.
(Resistance 120ohm 1/4W) between pin2(DMX-) and pin3(DMX+) of the last
fixture.
1.If you use a controller with 5 pins DMX output, you have to use a 5 to 3 pin adapter-
cable.
2.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plu and plu it in
the DMX-output of the last unit.
Please find the followin examples to address your DMX512 channel for the
first 4 packa es.
Caution
Take care using this equipment!
High voltage risk of electric shock
Before your initial star-up, please make sure that there is no dama e caused
durin transportation. Should there be any, consult with the dealer and do not use
the unit.
16CH Mode:
24CH Mode:
Please keep this User Manual for future consultation. If you sell the unit to
another user, be sure that they also receive this instruction booklet.
To maintain the equipment in ood work condition and to ensure safe operation, it
is necessary for the user to follow the safety instructions and warnin notes
written in the manual.
Warning
For your own safety, please read this user manual before operation
Use universal DMX controller to control the packa es, you have to set the DMX
address from 1 to 512 channels so that the unit can receive the DMX si nal. Caution
Before operating,make sure the voltage and frequence
of the power supply match the power requirements of the package
When switch on the li htin , LB280 is showin on the li htin , press E button to
enter into menu, use the TOUCH SCREEN directly or UP and DOWN to
choose the submenu AXXX to set the address. Once the address has been
selected, press ENTER button to store.

Professional Moving Head Beam Technical Specifations Professional Moving Head Beam Control Panel
You should find the followin items inside the carton packin :
Main Functions:
Technical Specifations
Volta e: AC110-240V,50/60HZ
Lamp: OSRAM P-VIP 280W lamp Professional Moving Head Beam DMX 512 Configuration
Power consumption: 450W
Lens: hi h precision optical lens
Pan: 540de ree (16bit) Tilt: 270de ree (16bit)
Color Wheel: 13 colors + open, with rainbow effect
Rotatin Gobo Wheel: 9 bidirectional & indexable obos + open
Gobo Wheel: 14 obos (with obo shakin / obo flow)+ open
Prism: 8-facet circular Rotatin Prism & 6-facet linear Rotatin Prism
Other Functions: ZOOM, Wash, Focus, Dimmer, Strobe
Packin Size: 725*440*790mm Gross Wei ht: 56k (2in1 fli ht case)
Operation Modes: ● DMX mode: 16CH/24CH ● Master/Slave mode ● Auto
Professional Moving Head Beam Control Panel
LCD display (Touch Screen): Showin the menus and selected function
Control Pannel / ENTER:
Mains input: Power in
DMX input / output: Use 3-pin XLR cable to link items to ether
Switch ON/OFF
2
3
2pc Movin Head, 2set OMEGA clamps, 2pc power cable, 2pc DMX cable,
1pc User Manual
1. A001 DMX Address Settin 2. Rpan Pan Reverse
3. Rtil Tilt Reverse 4. MODE Control Mode Settin : DMX: 16CH/24CH; AUTO; SOUD
5. DISP Display Reverse 6. LAMP Lamp ON/OFF
7. REST Reset 8. OPTO Optical Sensor Correction
Table of contents