IDEAL H2O 738317 Operating manual

SETUP AND MAINTENANCE GUIDE
Premium Water Filtration Systems
De-Chlorinator System
5,000 GPD
Product # 738317
De-Chlorinator System
10,000 GPD
Product # 738322

5,000 GPD De-Chlorinator system includes:
1. 4.5 in. x 10 in. polyspun sediment filter – removes sediment,
particulates, dirt, and rust.
2. 4.5 in. x 10 in. catalytic coconut carbon filter – removes chlorine,
odor, and other chemicals.
3. 5 ft. of white 3/8 in. inlet tubing.
4. 5 ft. of blue 3/8 in. outlet tubing.
5. Inline shut-off valve.
6. Wall mount bracket.
7. Garden hose connector.
8. Filter wrench – for safe removal of filter housing.
WHAT’S IN THE BOX?
Premium Water Filtration Systems
2
2
4
5
1
86
7
3

10,000 GPD De-Chlorinator system includes:
1. 4.5 in. x 20 in. polyspun sediment filter – removes sediment,
particulates, dirt, and rust.
2. 4.5 in. x 20 in. catalytic coconut carbon filter – removes chlorine,
odor, and other chemicals.
3. 5 ft. of white 3/8 in. inlet tubing.
4. 5 ft. of blue 3/8 in. outlet tubing.
5. Inline shut-off valve.
6. Wall mount bracket.
7. Garden hose connector.
8. Filter wrench – for safe removal of filter housing.
Premium Water Filtration Systems
3
2
4
5
1
8
6
7
3

4
The following steps will get you set up in just a few minutes. Please read
each step carefully. If you have any questions, please refer to our website at
www.IdealH2O.net for information and videos on setup & maintenance.
Step 1 – Connect the tubing to the unit:
Insert the BLUE filtered water outlet tubing into connection marked OUT. (fig. A).
Insert the WHITE water source inlet tubing into connection marked IN. (fig. B).
QUICK OPERATION GUIDE
(fig. B)(fig. A)

5
Step 2 – Starting up your De-chlorinator System:
Connect the white inlet tube to your water supply and slowly turn on the water
source. Once the sediment and carbon filter housings have water in them, turn
the water supply fully on.
RUN
30 - 40
MINUTES
RUN
30 - 40
MINUTES
Always run system 30 to 40 minutes before use,
especially after changing the filters.

6
REPLACING THE PRE-FILTERS
Step 1 – Unscrew the filter housing from the system using the filter wrench
included with your system.
Step 2 – Replace catalytic carbon and/or sediment pre-filters.
Step 3 – Screw the filter housing back onto the De-Chlorinator system,
firmly hand tightening these.
Do not use the
wrench to tighten.
Be cautious of
the o-rings

REPLACEMENT FILTER INFORMATION
7
A
B
C
D
5,000 GPD DE-CHLORINATOR
REPLACEMENT FILTER PART# FILTER REPLACEMENT TIMELINE
APolyspun Sediment Filter - 4.5” x 10” 738356 6 to 12 months
BCatalytic Carbon Filter - 4.5” x 10” 738380 6 to 12 months
10,000 GPD DE-CHLORINATOR
REPLACEMENT FILTER PART# FILTER REPLACEMENT TIMELINE
CPolyspun Sediment Filter - 4.5” x 20” 738358 6 to 12 months
DCatalytic Carbon Filter - 4.5” x 20” 738416 6 to 12 months

Exclusively distributed by:
www.sunlightsupply.com
For all warranty inquiries, please contact
Ideal H2O®at [phone].
Scan this QR code or visit our website for
how-to videos and other product information.
#111794 REV C • 02022017LS