iDevices IDEV0020 Assembly instructions

1
INSTALLATION AND SETUP GUIDE
iDEVICES SMART HOME SOLUTIONS

2
REQUIRES
• A compatible iDevices product
• iDevices Connected app
• Controlling this product requires
an iPhone, iPad or iPod touch that
supports Bluetooth®low energy
and is running iOS 8.1 or later
• Android™ 4.3+ device with
Bluetooth®low energy
WHAT’S INCLUDED
• iDevices Instant Switch with
CR2032 battery (pre-Installed)
• iDevices custom faceplate
• (2) Command™Strips from 3M
• Ground Wire Assembly
• (2) 22mm phillips
screws for gang box
installations
• (2) 6mm standard
screws for installing
standard faceplates,
(not included)
TOOLS NEEDED
When installing into a gang box, you
will need the following tools:
• Philips Screwdriver
• Flathead Screwdriver
RATINGS
3 VDC, 5.4mA
Replacement Battery: CR2032 ONLY
22mm 6mm

3
• The iDevices Instant Switch must be installed in a manner that conforms to all applicable national,
state, and local building codes.
• When installing with Command™Strip from 3M, do not install above a bed, onto wallpaper, or outdoors.
• The iDevices Instant Switch is intended for dry, indoor use only.
• Ambient operating conditions: 32º F to 104º F (0º C to 40º C), 0-90% humidity, non-condensing.
• The iDevices Instant Switch uses 1 CR2032 coin cell battery ONLY. Do not use a rechargeable battery. Using
an improper battery may damage the iDevices Instant Switch. Please dispose of this battery at a recycling
 facility.Contactyourlocalwastedisposalprovidertondarecyclecenterlocationnearestyou.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
!

4
BEFORE YOU START
• The iDevices Instant Switch requires a compatible iDevices
 productthatisoperatingon1.9.1rmwareorgreater.Besurethat
 youhaverstsetupthecompatibleproductinyourhomeusing
the iDevices Connected app before attempting to setup your
 InstantSwitch.Tondinformationoncompatibleproductsand
 howtoupdatermware,visitiDevicesinc.com/Compatibility/
Instant-Switch
• Wherever possible, install the iDevices Instant Switch in a non-
metal gang box and use a non-metal or metallic faceplate, as
metal gang boxes and faceplates can decrease the Bluetooth®
signal strength.

5
• It is YOUR responsibility to be sure that products are installed in
accordance with applicable building codes. Check with your local
 buildingofceifyouhavequestions.
• If you need further help on your Instant Switch installation, please
 visitoursupportpageatiDevicesinc.com/Support/Instant-Switch
• Download the free iDevices Connected app.

6
GETTING TO KNOW THE
iDEVICES INSTANT SWITCH
1
2
3
Turn On/Increase Brightness. (Note: Dimmable feature only available
when paired to a dimmable iDevices product). Single tap to turn on.
Press and hold to increase brightness level. Double tap to quickly
increase light to maximum brightness.
Turn Off/Decrease Brightness. (Note: Dimmable feature only available
when paired to a dimmable iDevices product). Single tap to turn off.
Press and hold to decrease brightness level. Double tap to quickly
decrease light to minimum brightness level.
Status LED. Provides setup status. Refer to LED color codes on page 30.

7
6
7
4
2
5
7
5
4
3
3M Command™ Strip Access Door. Remove
to access 3M Command™ Strip when removing
Instant Switch from wall.
Level. Built-in level ensures precise
installation.
Instant Switch Unit Removal. Press sides
to remove Instant Switch from mounting plate
to access battery.
Pairing Reset. Press and hold for
10 seconds, until LED blinks red.
Device Reset. Press and hold
7+1 simultaneously for 10
seconds, then release to cycle
power to the device.
+
7 1
16

8
GETTING TO KNOW THE
iDEVICES INSTANT SWITCH (CONT.)
8Ground Wire Assembly. Connect to Instant Switch when installing into
a gang box.

9
8
8

10
USING FOR THE FIRST TIME
REMOVE BATTERY PULL TAB
BeforeusingtheiDevicesInstantSwitchforthersttime,youwill
need to remove the battery tab. Pull the plastic tab out from the
back of the product and discard.
Once the battery tab is removed, the Instant Switch will
automatically enter pairing mode for 30 minutes.
NOTE: If 30 minutes have elapsed and you have not setup the
Instant Switch, you will need to press the Pairing Reset button 7to
re-enter pairing mode.

11
Next, launch the iDevices Connected
app. The app will guide you through
setup and placement of the Instant
Switch in your home.
Once the in-app setup is complete,
follow the steps on page 12 to
complete the installation.

12
INSTALLATION METHODS
There are 3 methods in which you may install your Instant Switch:
By itself on the wall, using the provided 3M Command™ Strip
and iDevices custom faceplate or a standard rocker faceplate
of your choice.
Next to an existing gang box, using the provided 3M
Command™Strip and a multiple switch faceplate of your
choice (not included).
Installed directly into a gang box using a standard rocker style
faceplate (not included).
Whichever method you choose, ensure your iDevices Instant
Switch is installed perfectly by using the built-in level.
1
2
3

13

14
INSTALLATION
INSTALL ON A WALL
•TomountyourInstantSwitchdirectlyontoawall,rstthoroughly
clean the wall’s surface with isopropyl alcohol to remove any dirt or dust.
• Remove the plastic backing to the Command™ Strip and align the
strip with the recessed area on the back of the Instant Switch.
• Peel off the other side of the plastic backing and ensure that the
 productislevelbeforepressingrmlytothewall.Holdfor
30 seconds.
• Install the magnetic iDevices faceplate, or a rocker style faceplate
of your choice. If the faceplate you choose requires screws, use the
shorter, 6mm screws provided to anchor the faceplate to the
Instant Switch.
1

15

16
INSTALL NEXT TO GANG BOX
• Install the 3M Command™ Strip onto the back of the
Instant Switch.
• Mount the faceplate onto the Instant Switch using the provided
6mm screws.
• Peel off the plastic backing of the 3M Command™ Strip.
• Carefully line up your faceplate with the existing wall switches and
press to the wall for 30 seconds.
• Install the remaining faceplate screws into the adjacent
wall switch(es).
2

17

18
INSTALL INTO GANG BOX
• Turn OFF the power to the circuit you are working on at your
home’s breaker or fuse panel.
• Install the ground wire assembly onto the access door of the
Instant Switch.
3

19

20
INSTALL INTO GANG BOX (CONT.)
• Connect the ground wire on the Instant Switch to the ground wire
in the gang box, which is usually bare copper or green.
3