idi 1000F-1 Product manual

L240-1429 REV A Image Diagnostics, Inc. Page 1
Manufacturer of Quality Medical Products
IDI Monitor Suspension System
Model IDI 1000F-1 and 1000F-2
with Adapter for Canon DST-1000A Ceiling Rails
Installation and Maintenance Guide
The text of this manual was originally written, approved and published by the manufacturer in
English. The information in this manual is subject to change without notice.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 2
Contents
A. INTRODUCTION ................................................................................................................................................3
B. SYMBOLS ...........................................................................................................................................................4
C. GENERAL SAFETY............................................................................................................................................6
D. SAFETY HAZARDS............................................................................................................................................7
E. INSTALLATION .................................................................................................................................................8
INSTALL DST-1000A CEILING RAIL ADAPTERS .........................................................................................8
INSTALL RAIL X/Y STOP .................................................................................................................................10
INSTALL CROSS RAIL END PLATE...............................................................................................................11
END-LOAD MONITOR MOUNT CARRIAGE ................................................................................................12
INSTALL MONITOR MOUNT...........................................................................................................................13
INSTALL MONITOR(S)......................................................................................................................................14
SET ROTATIONAL LIMITS..............................................................................................................................16
ELECTRICAL CONNECTIONS ........................................................................................................................17
INSTALL STATIONARY CABLE HANDLING ASSEMBLY........................................................................18
INSTALL MOBILE CABLE HANDLING ASSEMBLY..................................................................................19
DRESS CABLES ...................................................................................................................................................20
ADJUST WEIGHT COUNTERBALANCE .......................................................................................................21
YOKE BALANCE ADJUSTMENT.....................................................................................................................22
MONITOR MOUNT ASSEMBLY ROTATION RESISTANCE .....................................................................22
F. CLEANING THE EQUIPMENT .......................................................................................................................22
G. MAINTENANCE ...............................................................................................................................................23
H. CUSTOMER SUPPORT ....................................................................................................................................26
I. DISPOSAL GUIDELINES.................................................................................................................................27
J. APPROVALS.....................................................................................................................................................27

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 3
A. INTRODUCTION
The IDI 1000F Flat Panel Suspension System is designed to mount monitors used in
medical imaging procedures to the ceiling which can be repositioned by rolling along guide
rails. The system features a counterbalanced arm with vertical travel and internal cable
routing. A dual-axis flat panel monitor mount permits independent panel mounting and
positioning. This mobile package includes clip-mounted bridge rails.
PRODUCT DATA
Package Includes:
oMobile gantry and counterbalanced swing arm with 42" sweep radius, 25" vertical
travel and ±180° rotation.
oAnodized aluminum bridge rails with Easymount clip system.
oFlat panel array with ±180° rotation.
oArray includes display panel mounts with ±10° tilt.
oComplete installation package; meter box mounts, all mounting hardware and
cable management components; brackets, covers and "flexhaust" hose.
OPERATION
The monitors are moved along the overhead rails, positioned vertically, and rotated
manually using the handle of the monitor mount on the suspension system.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 4
B. SYMBOLS
Consult accompanying documents.
Failure to follow these instructions can cause accidents
resulting in serious injury to patient, user, and damage to equipment.
Warning!
Information or instructions shown near this symbol must be adhered to in
order to prevent a potentially hazardous situation which if not avoided,
could result in death, personal injury or damage to the equipment.
Electric Shock hazard.
Information or instructions shown near this symbol must be adhered to in
order to prevent a potentially hazardous situation which if not avoided, could
result in death, personal injury or damage to the equipment.
Protective Ground.
This is the common tie point between the AC monitor
cord grounds, frame ground, and service (main) ground.
Alternating Current.
Weight Limit.
Recycle.
Some of the materials can be recycled rather than discarded.
European Authorized
Representative:
Model of Table.
Serial Number of Table.
EC
REP
REF
SN
Advena Ltd. Tower Business Centre, 2nd Flr.,
Tower Street, Swatar, BKR 4013 Malta

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 5
Indication of European Conformity for sale in the European Economic Area
(EEA).
Item complying to Type B applied part per IEC 60601-1.
Date of manufacture of the device.
Location where device was manufactured.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 6
C. GENERAL SAFETY
Attention. Consult accompanying documents.
Failure to follow these instructions can cause accidents
resulting in serious injury to patient, user, and damage to
equipment.
Only qualified persons may install, operate or maintain this equipment.
Installation of this unit must adhere to applicable codes and authorities having any
jurisdiction over this installation. The customer's architect or engineer is responsible for
assuring that the structural support plans comply with all applicable codes and regulations.
The unit should be used only in rooms that comply with state, federal and local recommendations
concerning electrical safety when used in medical installations. All electrical connections shall be
done by licensed/approved electrician per national electric codes.
CAUTION: •Always switch off mains before performing
nonelectrical tests or maintenance.
•Many positions exist where equipment or patient
collision may occur. Care must be exercised
during equipment positioning to avoid a patient or
equipment collision.
Changes and additions to the equipment may be performed only by an authorized representative.
These changes must conform to regulations and accepted standards of good practice. To prevent
defeat of the built-in safety mechanisms, changes must be submitted in writing to the manufacturer
for review.
Use only parts specified by Image Diagnostics, Inc. when repairing or servicing this equipment.
This equipment is intended to only be used with Image Diagnostics, Inc. Cross (transverse)
rails.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 7
D. SAFETY HAZARDS
Installers and Operators using this equipment should understand the safety issues and operating
instructions provided.
Comments and questions regarding safety should be addressed to:
Customer Support
Image Diagnostics, Inc.
310 AUTHORITY DRIVE
FITCHBURG, MA 01420
USA
Or call IDI at [phone] or send fax to [phone]
Or call Toll Free at [phone]
SAFETY HAZARDS ALERTS
Alert
Circumstances for use
DANGER
Indicates an imminentlyhazardous situation which, if
not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury
or equipment damage.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 8
E. INSTALLATION
UNPACK
No special handling is required for unpacking this equipment at the site.
Conventional shipping materials are used.
Recycle or disposal of shipping material per local regulations
INSTALL DST-1000A CEILING RAIL ADAPTERS
Before Installing the Canon supplied longitudinal ceiling rails, make sure that there is at least
35 in. [89 cm] between one end of the rails and any obstructions facing them. This will allow
the complete length of the adaptors to be rolled into the ceiling rails.
1. Position each Rail Adaptor (left or right) so that the Bumper Stop is oriented toward the outside
of both Canon Ceiling Rails, then roll Rail Adapters into the inside channel of the Ceiling Rails
as shown in Figure 1.
Figure 1

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 9
Figure 2
2. Place the two Triangulation Bars onto the top surface of the rail adapter sub-assemblies and
line up the slots in the bars with the closest inner Rail Clip hole locations as shown in Figure
2.
3. Loosely attach two rail clips to each of the two rail adapters in the inner rail clip locations as
shown in Figure 2 using 3/8-16 x 2” painted bolts, flat washers, lock washers and nylon
locknuts. Make sure to orientate the Rail Clips as shown in Figure 2 so that they will be able
to clamp onto the IDI supplied Cross Rails.
Figure 3
4. Place and orientate 6ft.-8in. IDI Cross Rails against the inner rail clips (from assembly step 3)
and mount remaining four outer rail clips as shown in Figure 3. Slide the Cross Rails until
they are aligned and centered under both Rail Adapter sub-assemblies and adjust the

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 10
Triangulation Bars and rail clips until the 6ft.-8in. The rails are spaced 17-1/8in. apart at both
ends of the rails as shown in Figure 3.
5. Tighten rail clip hardware using Loctite #242 or equivalent.
INSTALL RAIL X/Y STOP
1. The X/Y stop unit should have a T-nut fastened to it with two socket head cap screws. Loosen
the screws for the T-nut and insert the X/Y Stop unit’s T-nut into one end of the IDI Cross Rail
nearest to the opposing system in the room. See Figure 4 for correct orientation.
Figure 4
2. Hand tighten screws until the system is fully installed and the final position of the stop is known
then tighten using Loctite #242 or equivalent.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 11
INSTALL CROSS RAIL END PLATE
1. Install only one Cross Rail End Plate sub-assembly at the far end of the Cross rails, making
sure that the rubber bumpers face in towards the rails. See Figure 5. Use Loctite #242 on all
threads. (The other Cross Rail End Plate sub-assembly can only be installed after the cable
handling hardware is installed.)
Figure 5

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 12
END-LOAD MONITOR MOUNT CARRIAGE
1. Remove packaging material from the carriage assembly.
2. Using a Hi-Jack or other suitable lift table, raise carriage (while it is still attached to pallet) up
and slide its wheels into the open end of the IDI Cross Rails. Make sure all carriage wheels
are engaged onto rails before lowering Hi-Jack.
3. Remove pallet and shipping bars from support unit.
4. If a Stationary/Mobile Cable Handling Assembly is going to be used with this suspension
system, then mount them at this stage. (Refer to instructions on pages 17-19)
5. Install the second Cross Rail End Plate on the open end of the IDI Cross Rails, making sure
the rubber bumpers face in towards the carriage. (See Figure 5 for reference) Use Loctite #242
on all threads.
WARNING! Failure to install both rail end plates may
result in serious injury to user and damage to
the equipment.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 13
INSTALL MONITOR MOUNT
NOTE TO INSTALLER: It is
important that the load be
balanced on the monitor
mount. Consider any
differences in size and weight
of the monitors. Refer to
Figure 6 for steps 1-6.
1. Remove wireway cover.
2. Insert rotation bearing into
the pivot plate on the top of
the monitor mount.
3. Install the thicker of the two
thrust rings onto the rotation bearing from inside the monitor mount frame.
4. Install the thinner stainless-steel thrust ring onto the rotation bearing from inside the monitor
mount frame.
5. Install six socket head cap screws with lock washers through the rotation cap, then through the
rotation bearing and into the pivot tube of the core assembly. Use Loctite #242 on hardware.
6. Apply a very little amount of Loctite #242 to six set screws and install them into the threaded
holes on the rotation cap. Install the set screws until they bottom out. They may be tightened
or loosened later to adjust rotational resistance.
WARNING! Failure to securely attach hardware may result
in serious injury to patient, user, and damage
to equipment.
Figure 4

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 14
INSTALL MONITOR(S)
Maximum weight of any individual monitor.
Maximum total weight of monitors.
1. On monitor mounts designed for two monitors (1000F-2), the plastic covers shown in Figure
7 will need to be temporarily removed to gain access to the rear of the monitor mounting
brackets.
2. For each monitor to be installed, insert screws into the top two mounting holes leaving a gap
below the head of the screw big enough to fit over the thickness of the mounting bracket to
which it is being mounted.
3. Install the monitor onto the mounting bracket by lowering the top mounting screws into the
slots on the top of the mounting bracket. Insert bottom mounting screws through the rear of
the mounting bracket into the monitor and tighten all four mounting screws. See Figure 7.
Figure 5
WARNING! Failure to securely attach hardware may result
in serious injury to patient, user, and damage
to equipment.
25 LBS
11 kg
44 kg
96 LBS

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 15
4. Monitor can be tilted and rotated by hand. If monitor fails to stay in position and tilts without
any outside assistance by hand, tighten the socket head cap screw on the pivot point of the
bracket.
NOTE TO INSTALLER: Ground studs have been provided to properly ground monitor(s).
Terminal strips have been provided for distribution of line voltage to monitor. See Figure
8. Cut and strip monitor power cord to fit.
WARNING! Remove plastic cover and remove block of
wood between gantry core and arm. Failure to
do so may result in serious injury to user and
damage to equipment.
Figure 6

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 16
SET ROTATIONAL LIMITS
If desired, the rotational stop pin bumper can be relocated to one of four possible mounting
locations. See Figure 9.
Figure 7
FOUR POSSIBLE
STOP PIN
MOUNTING POSITIONS

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 17
ELECTRICAL CONNECTIONS
1. Colors of conductors in power supply cords must be in accordance with IEC publication 60227
(amendment #1) or with IEC publication 60245.
Wiring Color Codes:
International: brown (line), blue (neutral), green/yellow (ground)
North America: black (line), white (neutral), green/yellow (ground)
2. Cable tie mounting platforms are supplied near the terminal block for anchoring the monitor
cords and the wires from the mains. Use nylon cable ties. (Tying the cord into a knot or tying
the ends with string shall not be used for cord anchorage).
3. Arrange the conductors of the power supply cord so that the protective earth conductor is not
subject to strain as long as the phase conductors are in contact with their terminals.
4. All power cords used for mains connection must have double insulation. Conduit provided for
routing cables must not be relied on for insulation.
Figure 8
5. Connect all Monitor and service ground wires as shown in Figure 10. (The number of wires
varies with the number of monitors installed).
(#10-32 HARDWARE)
NUT "B"
MAIN GROUND WIRE
FROM SERVICE
NUT "A"
under split lockwasher and nut "A".
First attach main ground wire
Attach all other ground wires
between nut "A", lockwashers,
and nut "B".

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 18
INSTALL STATIONARY CABLE HANDLING ASSEMBLY
1. Determine which end of the IDI Cross Rail the Stationary Cable Handling Assembly will be
positioned onto. If it is to be at the far end of the rail, slide the assembly into the rail track
prior to positioning the Mobile Cable Handling Assembly. If assembly is to be positioned at
the near end of rail, slide into the rail after positioning the Mobile Cable Handling Assembly.
The Stationary Cable Handling Assembly is typically mounted approximately 6 inches (15cm)
from the end of the rail. See Figure 11.
Figure 9
2. Apply Loctite #242 to threads on set screws and then tighten until secured in place.
3. Remove retainer by removing both button head cap screws.
4. Place cable hose into cable carrier clamp.
5. Reinstall retainer and mounting screws.

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 19
INSTALL MOBILE CABLE HANDLING ASSEMBLY
1. Slide two Nut Plates into the outer track of the Cross Rails. Apply Loctite #242 to the threads
of two standoffs and then assemble into nut plates hand tight only. See Figure 12.
Figure 10
2. Align Safety Brackets with the inner threaded holes of the Nut Plates and fasten with a lock
washer and a 3/8in. long socket head cap screw.
3. Slide Cable Trolley Assembly onto Cable Hanger shaft. See Figure 13.
4. Assemble Cable Hanger shaft through holes in Safety Brackets and into the side holes of each
shaft support.
5. Install mounting screw through the shaft supports, through the hole in the end of the Cable
Hanger shafts and into the standoffs. Lightly tighten mounting screws.
Figure 11

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails
L240-1429 REV A Image Diagnostics, Inc. Page 20
6. Position shaft/cable handling assembly created from steps 1-5 to desired location along length
of rail. Torque standoffs to nut plates approximately 35 to 50 inch-pounds (4.2 to 6.0Nm) and
tighten socket head cap screws. Use Loctite #242 on threaded hardware.
CAUTION! Over tightening the standoff will weaken or
break the thread connecting the standoff to the
nut plate causing attached components to fall.
DO NOT loosen or adjust the exposed length of
the setscrew on the standoff.
DRESS CABLES
1. When the monitors have been properly installed, it is recommended that the cables run through
the pivot tube as shown in Figure 14. Attach 2in. (5cm) Flexaust hose (provided) to pivot tube
and route underneath the arm via the cable hose clamps. Rotate entire system to maximum
positions. The system should not drift from any position. If it does, check that enough cable
has been left to allow freedom of motion.
36" [914mm]
HANDLING ASSEMBLY
MOBILE CABLE
48" [1220mm]
BETWEEN COMPONENTS
APPROX. LENGTH OF CABLE HOSE
*
[400mm]
15 3/4"
47" [1200mm]
*
LOCATIONS MAY REQUIRE SOME VARIATION
ACTUAL ROOM LAYOUT AND EQUIPMENT
CONFIGURATION
OPTIMUM CABLE HOSE
HANDLING ASSEMBLY
STATIONARY CABLE
*
Figure 12
ARM
PIVOT TUBE