IEI Technology IMBA-ADL-H610 User manual

ATX Motherboard Supports LGA1700 12th/13th Gen. Intel® Core™
i9/i7/i5/i3, Pentium® and Celeron® Processor, DDR4,
Triple Independent Display, Dual GbE LAN,
USB 3.2, SATA 6Gb/s, and RoHS
IMBA-ADL-H610
Quick Installation Guide
Version 1.0
September 1, 2022
Package List
IMBA-ADL-H610 package includes the following items:
 1 x IMBA-ADL-H610 single board computer
 2 x SATA cable
 1 x I/O shielding
 1 x QIG
©2022 Copyright by IEI Integration Corp.
All rights reserved.

2
Specifications
 CPU:
LGA1700 12th/13th Generation Intel® Core™ i9/i7/i5/i3, Celeron®
and Pentium® processors (up to 65W TDP)
 Chipset:
Intel® H610/H610E
 Memory:
Two 288-pin dual-channel unbuffered DDR4 SDRAM DIMM slots
supporting up to 64 GB memory
 BIOS:
AMI UEFI BIOS
 Graphics Engine:
New Intel® Xe Graphics architecture with SRIOV, Genlock
 Display Output:
Triple independent display
1 x DP (up to 4096 x 2304 @ 60Hz)
1 x HDMI (up to 4096 x 2304 @ 30Hz)
1 x IEI iDPM eDP/ LVDS/ VGA module
 Ethernet:
LAN1: Intel® I219 LM controller
LAN2: Intel® I225V 2.5GbE controller
 External I/O Interface:
2 x USB 3.2 Gen 2 (Type-A) (10Gb/s)
2 x USB 3.2 Gen 1 (Type-A) (5Gb/s)
4 x USB 2.0 (Type-A)
2 x RS-232/422/485 (RS-485 support AFC)
 Internal I/O Interface:
4 x SATA 6Gb/s
2 x USB 2.0 (2x4 pin, p=2.54)
4 x RS-232 (2x5 pin, p=2.54)

3
 Audio:
1 x iAUDIO supports IEI AC-KIT-888S Audio Kit (2x5 pin, p=2.0)
 Front Panel:
1 x Front panel (2x7 pin, p=2.54; power LED, HDD LED, speaker,
power button, reset button)
 LAN LED:
2 x LAN LED (1x2 pin, p=2.54)
 Expansions:
1 x PCIe Gen5 x16 slot
1 x PCIe Gen4 x4 open-end slot
2 x PCIe Gen3 x1 slot
2 x PCI slot
 Digital I/O:
1 x 12-bit digital I/O (2x7 pin, p=2.0)
 SMBus:
1 x SMBus (1x4 pin, p=1.25)
 I
2C:
1 x I2C (1x4 pin, p=1.25)
 Fan Connector:
1 x CPU fan connector (1x4 pin)
2 x System fan connector (1x4 pin)
 Chassis Intrusion:
1 x Chassis intrusion connector (1x2 pin, p=2.54)
 TPM
Intel® PTT (TPM 2.0)
 Power Supply:
ATX/AT power supply
Support AT/ATX mode
ErP/EuP compliant
 Power Consumption:
[email protected], [email protected], [email protected], [email protected]
(Intel® Core™ i7-12700E CPU with two 32 GB 2933 MHz DDR4
memory, EuP mode enabled)

4
 Watchdog Timer:
Software programmable support 1–255 sec. system reset
 Operation Temperature: 0°C – 60°C
 Storage Temperature: -30°C – 70°C
 Operation Humidity: 5% – 95%, non-condensing
 Dimensions: 244 mm x 305 mm
 Weight: GW:900 g / NW:400 g
 Safety: CE/FCC compliant
All the drivers and utility for the IMBA-
ADL-H610 are available on IEI
Resource Download Center. Type
IMBA-ADL-H610 and press Enter to
find all the relevant software, utilities,
and documentation. To install
software from the downloaded ISO
file, mount the file as a virtual drive to
view its content.
IEI Resource Download Center
https://download.ieiworld.com

5
Ordering Information
 IMBA-ADL-H610-R10:
ATX motherboard supports LGA1700 12th/13th Generation Intel®
Core™ i9/i7/i5/i3, Pentium® and Celeron® processor, DDR4, triple
independent display, dual GbE LAN, USB 3.2, SATA 6Gb/s, and
RoHS
 AC-KIT-888S-R10:
Realtek ALC888S 7.1 Channel HD Audio board, RoHS
 CB-USB02A-RS:
Dual-port USB cable with bracket, 300mm, p=2.0
 32102-000100-200-RS:
SATA power cable, MOLEX 5264-4P to SATA15P
 32205-000702-100-RS:
RS-232 cable, 230mm, p=2.54
 iDPM-eDP-R10:
eDP to eDP converter board (for IEI iDPM connector)
 iDPM-LVDS-R10:
eDP to LVDS converter board (for IEI iDPM connector)
 19100-000323-00-RS:
LGA1700 CPU cooler, 65W

6
Jumpers Setting and Connectors
LABEL FUNCTION
J_ATX_AT1 AT/ATX power mode setting
J_CMOS1 Clear CMOS jumper
ME_FLASH1 Flash descriptor security override jumper
IAUDIO Audio connector for IEI AC-KIT-888S kit
ATX1 ATX power connector
CPU12V1 ATX CPU 12V power connector
BAT2 RTC battery connector
CHASSIS1 Chassis intrusion connector
CHA_DIMM1, CHB_DIMM1 DDR4 DIMM slots
DIO1 Digital I/O connector
DEBUG_1 EC debug connector
CPU_FAN1, SYS_FAN1,
SYS_FAN2 Fan connectors
F_PANEL1 Front panel connector
J_I2C1 I2C connector
JLAN_LED1 LAN1 link LED connector
JLAN_LED2 LAN2 link LED connector
COM3, COM4,
COM5, COM6 RS-232 serial port connectors
J1 RAA229134 FW flash connector
J2 LT86101X FW flash connector
SATA1, SATA2,
SATA3, SATA4 SATA 6Gb/s connectors
J_SMB1 SMBus connector
JSPI1 Flash SPI ROM connector
JEC1 Flash EC ROM connector
USB2_CN1 Internal USB 2.0 connector
IDPM IEI iDPM slot
PCI1, PCI2 PCI slots
PCIE2, PCIE4 PCIe x1 slots
PCIE3 PCIe x4 slot
PCIE1 PCIe x16 slot
PWR_BTN1 Onboard power button

7
COM1_2 External dual RS-232/422/485 connector
HDMI_DP1 External HDMI and DP combo connector
LAN1_USB1 External 1GbE RJ-45 and dual USB 3.2
Gen 1 combo connector
LAN2_USB2 External 2.5GbE RJ-45 and dual USB 3.2
Gen 2 combo connector
USB2_1 External quad USB 2.0 connector
J_ATX_AT1: AT/ATX Power Mode Setting
PIN NO. DESCRIPTION
Short A - B ATX Power Mode (default)
Short B - C AT Power Mode
J_CMOS1: Clear CMOS Button
Status DESCRIPTION
NC Keep CMOS Setup
(Normal Operation)
Press Clear CMOS Setup
ME_FLASH1: Flash Descriptor Security Override Jumper
PIN NO. DESCRIPTION
Open Disabled (default)
Short Enabled
IAUDIO: Audio Connector for IEI AC-KIT-888S kit
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 HDA_SYNC_R 2 HDA_BCLK_R
3 HDA_SDO_R 4 HDA_PCBEEPC
5 HDA_SDI_0_R 6 HDA_RST_R
7 +5V 8 GND
9 +12V 10 GND

8
ATX1: ATX Power Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power good 20 -5V
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 GND
CPU12V1: ATX CPU 12V Power Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 5 +12V
2 GND 6 +12V
3 GND 7 +12V
4 GND 8 +12V
BAT2: RTC Battery Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VBATT 2 GND
CHASSIS1: Chassis Intrusion Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 CASEOPEN_N 2 GND

9
DIO1 : Digital Input/Output Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 VCC
3 Output 5 4 Output 4
5 Output 3 6 Output 2
7 Output 1 8 Output 0
9 Input 5 10 Input 4
11 Input 3 12 Input 2
13 Input 1 14 Input 0
DEBUG_1: EC Debug Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 NC 4 EDICLK
2 EDICS 5 EDIDI
3 EDIDO 6 GND
CPU_FAN1: CPU Fan Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 +12V
3 FANIO 4 PWM (+5V)
SYS_FAN1, SYS_FAN2: System Fan Connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 +12V
3 FANIO 4 PWM (+5V)

10
F_PANEL1: Front Panel Connector
PIN DESCRIPTION PIN DESCRIPTION
PWR
LED
1 PWR_LED+ 2 SPKR+
SPKR
3 NC 4 NC
5 PWR_LED- 6 NC
PWR
BTN
7 PWR_BTN+ 8 SPKR-
9 PWR_BTN- 10 NC
HDD
LED
11 HDD_LED+ 12 Reset+ RESET
13 HDD_LED- 14 Reset-
J_I2C1: I2C Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 3 I2C_CLK
2 I2C_DATA 4 +5V
JLAN_LED1: LAN1 Link LED Connector
PIN DESCRIPTION PIN DESCRIPTION
1 +3.3V 2 LAN1_LED_LNK#_ACT
JLAN_LED2: LAN2 Link LED Connector
PIN DESCRIPTION PIN DESCRIPTION
1 +3.3V 2 LAN2_LED_LNK#_ACT
COM3, COM4, COM5, COM6: RS-232 Serial Port Connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 DCD 2 DSR
3 RXD 4 RST
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 GND

11
J1: RAA229134 FW Flash Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 SDA 2 SCL
3 GND
J2: LT86101X FW Flash Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 SDA 2 SCL
3 GND
SATA1, SATA2, SATA3, SATA4: SATA 6Gb/s Connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 5 SATA_RX‐
2 SATA_TX+ 6 SATA RX+
3 SATA_TX‐ 7 GND
4 GND 8 N/C
J_SMB1: SMBus Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 3 SMB_CLK
2 SMB_DATA 4 +5V
JSPI1: Flash SPI ROM Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 4 SPI_CLK
2 SPI_CS# 5 SPI_SI
3 SPI_SO 6 GND

12
JEC1: Flash EC ROM Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 FSCE# 2 +3.3V
3 FMISO 4 NC
5 EC_DET_FLASH 6 FSCK
7 GND 8 FMOSI
USB2_CN1: Internal USB 2.0 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 GND
3 USB_DATA- 4 USB_DATA+
5 USB_DATA+ 6 USB_DATA-
7 GND 8 VCC
COM1, COM2: External RS-232/422/485 Connectors
RS-232 RS-422 RS-485
1 DCD TXD422- TXD485-
2 RXD TXD422+ TXD485+
3 TXD RXD422+ --
4 DTR RXD422- --
5 GND -- --
6 DSR -- --
7 RTS -- --
8 CTS -- --
9 RI -- --

13
HDMI_DP1
External DP Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 LANE0P 11 GND
2 GND 12 LANE3N
3 LANE0N 13 CONFIG_A_1
4 LANE1P 14 CONFIG_A_2
5 GND 15 AUXP
6 LANE1N 16 GND
7 LANE2P 17 AUXN
8 GND 18 HPD
9 LANE2N 19 GND
10 LANE3P 20 +5V
External HDMI Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
21 HDMI_DATA2P 31 GND
22 GND 32 HDMI_CLKN
23 HDMI_DATA2N 33 N/C
24 HDMI_DATA1P 34 N/C
25 GND 35 HDMI_CLK
26 HDMI_DATA1N 36 HDMI_SDA
27 HDMI_DATA0P 37 GND
28 GND 38 +5V
29 HDMI_DATA0N 39 HDMI_HPD
30 HDMI_CLKP

14
LAN1_USB1
External Dual USB 3.2 Gen 1 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 10 VCC
2 USB_DATA- 11 USB_DATA-
3 USB_DATA+ 12 USB_ DATA+
4 GND 13 GND
5 USB3_RX- 14 USB3_RX-
6 USB3_RX+ 15 USB3_ RX+
7 GND 16 GND
8 USB3_TX- 17 USB3_TX-
9 USB3_TX+ 18 USB3_TX+
1GbE RJ-45 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
20 LAN1_MD0+ 26 LAN1_MD3+
21 LAN1_MD0- 27 LAN1_MD3-
22 LAN1_MD1+ 29 VCC
23 LAN1_MD1- 30 ACT
24 LAN1_MD2+ 31 100-
25 LAN1_MD2- 32 1000-

15
LAN2_USB2
External Dual USB 3.2 Gen 2 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 10 VCC
2 USB_DATA- 11 USB_DATA-
3 USB_DATA+ 12 USB_ DATA+
4 GND 13 GND
5 USB3_RX- 14 USB3_RX-
6 USB3_RX+ 15 USB3_ RX+
7 GND 16 GND
8 USB3_TX- 17 USB3_TX-
9 USB3_TX+ 18 USB3_TX+
2.5GbE RJ-45 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
20 LAN2_MD0+ 26 LAN2_MD3+
21 LAN2_MD0- 27 LAN2_MD3-
22 LAN2_MD1+ 29 VCC
23 LAN2_MD1- 30 ACT
24 LAN2_MD2+ 31 2500-
25 LAN2_MD2- 32 1000-
USB2_1: External Quad USB 2.0 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
11 USB_VCC 31 USB_VCC
12 D- 32 D-
13 D+ 33 D+
14 GND 34 GND
21 USB_VCC 41 USB_VCC
22 D- 42 D-
23 D+ 43 D+
24 GND 44 GND

16
Board Layout: Jumper and Connector Locations
(Unit: mm)