IEI Technology NANO-8522 User manual

1
EPIC Intel® Pentium® M/Celeron® M CPU with
VGA/LVDS, SATA, LAN and Audio
NANO-8522
Quick Installation Guide
Version 1.2
Aug. 31, 2007
Package Contents
NANO-8522 package includes the following items:
 1 x NANO-8522 single board computer
 1 x IDE flat cable 44p/44p
 1 x KB/MS Y cable
 1 x Audio cable
 2 x SATA cable
 1 x SATA Power cable
 1 x Power cable
 2 x RS-232 cable
 1 x mini jumper pack
 1 x Utility CD
 1 x QIG (Quick Installation Guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
 CPU: Intel® Celeron® M 600MHz 512K cache / 1.0GHz zero cache
processor
(Socket 479 Intel® Pentium® M,Celeron® M 400MHz FSB(Banias
core) up to 2.10GHz)

System Chipset: Intel 852GM+ICH4

BIOS: AMI BIOS

System memory: 1x 200-Pin SO-DIMM DDR 266MHz up to 1GB

Ethernet
Intel® 82541PI GbE chipset with ASF2.0 remote control support
Intel® 82551ER Ethernet chipset
 I/O
I/O Interface:
2 x SATA with ALI M5283 RAID 0,1 function support
6 x USB 2.0
1 x CF Type II
3 x RS-232
1 x RS-232/422/485
1 x PS/2 KB/MS
1 x IDE
 Expansions: 1 x PC-104(PCI bus)

Audio: Realtek ALC655 with AC'97 codec

Digital I/O: 8-bit digitl I/O,4-bit input/ 4-bit output by super I/O
 IrDA: By super I/O

Super I/O: W83627EHG
 Display Interface:
VGA integrated in Intel® 852GM
18-bit dual channel LVDS
 Watchdog timer
Software programmable supports 1~255 sec. system reset

Power Supply: +12V only, AT/ATX support

3
 Power Consumption:
[email protected]
(ULV Intel®Celeron® M 800MHz zero cache with DDR 266 MHZ,256
MB RAM)
[email protected]
(Pentium M 1.7GHz/L2-2M withDDR266MHz,512MB RAM)

Humidity: Operation: 5% ~ 95%, non-condensing
 Temperature: 0 ~ 60°C( 32 ~ 140°F)

Dimension: 165 mm x 115 mm

Weight: GW: 1100g; NW: 250g
Ordering Information
NANO-8522E-1GZ-R12
EPIC SBC with Intel® Celeron® M 1GHz zero cache processor on board with
VGA/LVDS, LAN, SATA and Audio
NANO-8522E-600Z-R12
EPIC SBC Intel® Celeron® M 600MHz 512K cache processor on board with
VGA/LVDS, LAN, SATA and Audio
NANO-8522G-R12
EPIC SBC Socket 479 Intel® Pentium® M/Celeron® M(Banias core/90nm)
Processor FSB400MHz, VGA/LVDS, GbE, SATA and Audio
CF-479B-RS: CPU Cooler
32000-070300-RS: USB cable
32200-015100-RS: LPT cable
32200-026500-RS: RS-232/422/485 cable
32100-052100-RS: ATX Power Cable
Jumpers setting and Connectors
JP1: Compact Flash Master /
Slave Selector
JP1 DESCRIPTION
NONE Slave
1-2 Master
JP2: Com2 RS232 / RS422 /
RS485 Selector
JP2 DESCRIPTION
1-2 RS-232
3-4 RS-422
5-6 RS-485

4
JP4: Clear CMOS Setup
(Reserve Function)
JP4 DESCRIPTION
1-2 Normal Operation
2-3 Clear CMOS Setup
JP5: PC104+ SERIRQ net to
CN3 pin B1 Selector
JP5 DESCRIPTION
NONE Disconnect
3-4 Connect
JP6: LCD Voltage Selector
(LVDS1 pin27~30)
JP6 DESCRIPTION
1-2 LCDVCC = +3.3V
2-3 LCDVCC = +5V
AUDIO: Audio connector (Box-header 5x2 2.0mm)
Pin Description Pin Description
1 LINE_OUT-R 2 LINE_IN-R
3 GND 4 GND
5 LINE_OUT-L 6 LINE_IN-L
7 GND 8 GND
9 MIC-IN 10 NC
BT1: Battery Connector
JP6 DESCRIPTION
1-2 BAT+
2-3 GND
DIO1:4 BIT GPIO Connector
Pin Description Pin Description
1 GND 2 VCC
3 OUT0 4 OUT1
5 OUT2 6 OUT3
7 IN0 8 IN1
9 IN2 10 IN3
CN4:12V input Connector
Pin Description Pin Description
2 GND 4 VCC12
1 GND 3 VCC12

5
CN5: LED Connector
Pin Description
1 +5V
2 GND
3 VCC5 LED+
4 GND
5 HDD LED+
6 HDD LED-
CN6: Compact Flash Connector(Secondary IDE)
Pin Description Pin Description
1 GROUND 26 VCC-IN CHECK1
2 DATA3 27 DATA11
3 DATA4 28 DATA12
4 DATA5 29 DATA13
5 DATA6 30 DATA14
6 DATA7 31 DATA15
7 HDC_CS0# 32 HDC_CS1
8 N/C 33 N/C
9 GROUND 34 IOR#
10 N/C 35 IOW#
11 N/C 36 N/C
12 N/C 37 INTERRUPT
13 VCC_COM 38 VCC_COM
14 N/C 39 CSEL
15 N/C 40 N/C
16 N/C 41 HDD_RESET
17 N/C 42 IORDY
18 SA2 43 N/C
19 SA1 44 VCC_COM
20 SA0 45 HDD_ACTIVE#
21 DATA0 46 N/C
22 DATA1 47 DATA8
23 DATA2 48 DATA9
24 N/C 49 DATA10
25 VCC-IN CHECK2 50 GROUND

6
COM2: Serial Port2 connector (Pin-header 7x2 2.0mm)
Pin Description Pin Description
1 DCD# 2 DSR#
3 RxD 4 RTS#
5 TxD 6 CTS#
7 DTR# 8 RI#
9 GND 10 GND
11 TxD485+ 12 TxD485-
13 RxD485+ 14 RxD485-
COM3: Serial Port3 Connector (Pin-header 5x2 2.0mm)
Pin Description Pin Description
1 DCD# 2 DSR#
3 RX 4 RTS#
5 TX 6 CTS#
7 DTR# 8 RI#
9 GND 10 GND
COM4: Serial Port4 Connector (Pin-header 5x2 2.0mm)
Pin Description Pin Description
1 DCD# 2 DSR#
3 RX 4 RTS#
5 TX 6 CTS#
7 DTR# 8 RI#
9 GND 10 GND
FAN1: CPU fan
Pin Description
1 Fan Speed Detect
2 +12V
3 GND
KBMS1: 6-pin header
Keyboard & Mouse Connector
Pin Description
1 VCC5
2 MOUSE DATA
3 MOUSE CLOCK
4 KEYBOARD DATA
5 KEYBOARD CLOCK
6 GND
J2: ATX Power connector
Pin Description
1 5VSB
2 GROUND
3 PSON

7
LPT1: Parallel Port Connector
Pin Description Pin Description
1 STROBE# 14 AUTO FORM FEED #
2 DATA 0 15 ERROR#
3 DATA 1 16 INITIALIZE
4 DATA 2 17 PRINTER SELECT LN#
5 DATA 3 18 GROUND
6 DATA 4 19 GROUND
7 DATA 5 20 GROUND
8 DATA 6 21 GROUND
9 DATA 7 22 GROUND
10 ACKNOWLEDGE 23 GROUND
11 BUSY 24 GROUND
12 PAPER EMPTY 25 GROUND
13 PRINTER SELECT 26 N/C
Ir1: IrDa Connector
Pin Description
1 VCC5
2 N/C
3 IrRxD
4 GROUND
5 IrTxD
CN1: LCD Inverter Connector
Pin Description
1 LCD_BKLTCTL
2 GROUND
3 VCC12
4 GROUND
5 LCD_BKLEN

8
LVDS1: LCD Interface Connector – support LVDS 18 BIT 2 CH
Pin Description Pin Description
2 GND 1 GND
4 AY0- 3 AY0+
6 AY1- 5 AY1+
8 AY2- 7 AY2+
10 AYCLK- 9 AYCLK+
12 AY3- 11 AY3+
14 GND 13 GND
16 BY0- 15 BY0+
18 BY1- 17 BY1+
20 BY2- 19 BY2+
22 BYCLK- 21 BYCLK+
24 BY3- 23 BY3+
26 GND 25 GND
28 LCDVCC 27 LCDVCC
30 LCDVCC 29 LCDVCC
PWRON: ATX POWER
BUTTON Connector
Pin Description
1 Button 1(GND)
2 Button 2(VCC)
RST1: Reset Connector
Pin Description
1 Reset 1(3.3V)
2 Reset 2(GND)

9
Board Layout: Jumper and Connector Locations

10
U14 Heat Sink Height