IEI Technology IBX-660 series User manual

IBX-660 Industrial Edge Storage Server
Page i
User Manual
IBX-660 Industrial server
MODEL:MODEL:
IBX-660 Series
4-bay Industrial Data Storage PC
for Smart Factory and Harsh Environment
Rev. 1.00 – April 25, 2018

IBX-660 Industrial Edge Storage Server
Page ii
Revision
Date Version Changes
April 25, 2018 1.00 Initial release

IBX-660 Industrial Edge Storage Server
Page iii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

IBX-660 Industrial Edge Storage Server
Page iv
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.

IBX-660 Industrial Edge Storage Server
Page v
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 MODEL VARIATIONS ................................................................................................... 2
1.3 FEATURES................................................................................................................... 3
1.4 FRONT PANEL............................................................................................................. 3
1.5 REAR PANEL............................................................................................................... 4
1.6 BOTTOM SURFACE...................................................................................................... 5
1.7 HARDWARE SPECIFICATIONS ...................................................................................... 6
1.8 DIMENSIONS............................................................................................................... 8
2 UNPACKING................................................................................................................. 9
2.1 UNPACKING.............................................................................................................. 10
2.2 PACKING LIST........................................................................................................... 10
2.3 OPTIONAL ITEMS.......................................................................................................11
3 INSTALLATION ......................................................................................................... 12
3.1ANTI-STATIC PRECAUTIONS...................................................................................... 13
3.2 INSTALLATION PRECAUTIONS................................................................................... 13
3.3 INSTALLATION PROCEDURE...................................................................................... 14
3.4 SO-DIMM INSTALLATION (OPTIONAL).................................................................... 15
3.5 HARD DRIVE INSTALLATION..................................................................................... 17
3.6 MOUNTING THE SYSTEM .......................................................................................... 20
3.6.1 Mounting with Optional Wall Mount Kit ......................................................... 20
3.7 POWER-ON PROCEDURE........................................................................................... 21
3.7.1 Installation Checklist....................................................................................... 21
3.7.2 Terminal Block Pinouts.................................................................................... 22
3.7.3 Power-on Procedure ........................................................................................ 22
3.8AVAILABLE DRIVERS ................................................................................................ 23
3.8.1 Driver Download............................................................................................. 24
4 BIOS.............................................................................................................................. 26

IBX-660 Industrial Edge Storage Server
Page vi
4.1 INTRODUCTION......................................................................................................... 27
4.1.1 Starting Setup................................................................................................... 27
4.1.2 Using Setup...................................................................................................... 27
4.1.3 Getting Help..................................................................................................... 28
4.1.4 BIOS Menu Bar................................................................................................ 28
4.2 MAIN........................................................................................................................ 29
4.3ADVANCED............................................................................................................... 30
4.3.1 Hardware Monitor ........................................................................................... 31
4.3.2 CPU Configuration.......................................................................................... 32
4.3.3 USB Configuration........................................................................................... 33
4.4 CHIPSET ................................................................................................................... 34
4.5 SECURITY................................................................................................................. 36
4.6 BOOT........................................................................................................................ 37
4.7 SAVE &EXIT............................................................................................................ 38
5 MAINTENANCE......................................................................................................... 40
5.1 COMPONENT REPLACEMENT PROCEDURE ................................................................ 41
A REGULATORY COMPLIANCE.............................................................................. 42
B SAFETY PRECAUTIONS......................................................................................... 47
B.1 SAFETY PRECAUTIONS............................................................................................. 48
B.1.1 General Safety Precautions............................................................................. 48
B.1.2 Anti-static Precautions .................................................................................... 49
B.1.3 Product Disposal............................................................................................. 50
B.2 MAINTENANCE AND CLEANING PRECAUTIONS........................................................ 50
B.2.1 Maintenance and Cleaning.............................................................................. 50
B.2.2 Cleaning Tools................................................................................................. 51
C HAZARDOUS MATERIALS DISCLOSURE......................................................... 52

IBX-660 Industrial Edge Storage Server
Page vii
List of Figures
Figure 1-1: IBX-660 Industrial Edge Storage Server...................................................................2
Figure 1-2: Front Panel ..................................................................................................................3
Figure 1-3: Rear Panel....................................................................................................................4
Figure 1-4: Bottom Surface ...........................................................................................................5
Figure 1-5: Dimensions (mm/inch)................................................................................................8
Figure 3-1: Bottom Panel Removal.............................................................................................15
Figure 3-2: SO-DIMM Installation ................................................................................................16
Figure 3-3: Front Panel Removal ................................................................................................17
Figure 3-4: HDD Tray Removal....................................................................................................18
Figure 3-5: HDD Tray Installation................................................................................................18
Figure 3-6: HDD Installation ........................................................................................................19
Figure 3-7: HDD Installation ........................................................................................................19
Figure 3-8: Mounting Bracket Installation..................................................................................21
Figure 3-9: Terminal Block Pinouts............................................................................................22
Figure 3-10: Power Button and Power Input Connector...........................................................22
Figure 3-11: Power LED ...............................................................................................................23
Figure 3-12: IEI Resource Download Center..............................................................................23

IBX-660 Industrial Edge Storage Server
Page viii
List of Tables
Table 1-1: IBX-660 Model Variations.............................................................................................2
Table 1-2: Hardware Specifications..............................................................................................7
Table 2-1: Package List................................................................................................................11
Table 4-1: BIOS Navigation Keys................................................................................................28

IBX-660 Industrial Edge Storage Server
Page 1
Chapter
1
1 Introduction

IBX-660 Industrial Edge Storage Server
Page 2
1.1 Overview
Figure 1-1: IBX-660 Industrial Edge Storage Server
The 4-bay compact IBX-660 is powered by an industrial-grade quad-core 1.91 GHz Intel®
Atom™E3845 processor, DDR3L RAM configurations, and two gigabit LAN ports to
deliver remarkable speeds.
Engineered with a rugged steel body and no moving parts, this small form factor IBX-660
server is capable of operating under wide temperatures from -40°C to +50°C (-40°F ~
122°F) in fanless operation. It is compliant with the military-grade
MIL-STD-810G-514.6E-1 simulation test for anti-vibration.
The IBX-660 features dual power inputs that can ensure continual operation in various
locations with 9 ~ 36 volts DC support. The ACC on mode is designed for vehicle
applications and the use of the ACC signal can control power on/off.
1.2 Model Variations
The model variations of the IBX-660 are listed below.
Model No. Pre-installed Memory
IBX-660 N/A
IBX-660-8G 8 GB DDR3L
Table 1-1: IBX-660 Model Variations

IBX-660 Industrial Edge Storage Server
Page 3
1.3 Features
The IBX-660 has the following features
RoHS compliant design
Fanless system
1.91GHz Intel® Atom™E3845 quad-core processor
Supports DDR3L SO-DIMM memory
Dual GbE LAN for high speed network applications
Support four 2.5” SSD or HDD
Extended temperature range
1.4 Front Panel
The IBX-660 front panel contains six LED indicators:
1 x Status LED (green: power on; flashes green: sleep mode)
1 x LAN LED (orange: disk data is being accessed from the network)
4 x HDD LED
An overview of the front panel is shown in Figure 1-2 below.
Figure 1-2: Front Panel

IBX-660 Industrial Edge Storage Server
Page 4
1.5 Rear Panel
The rear panel of the IBX-660 provides access to the following external I/O connectors.
1 x 12 V DC power input jack
1 x 9 V ~ 36 V DC power input terminal block (4-pin)
1 x Audio mic-in jack
1 x Audio out jack
1 x HDMI connector
2 x RJ-45 GbE connector
2 x USB 2.0 port connector
2 x USB 3.0 port connector
1 x Kensington security slot
1 x Power button
1 x ACC on/off switch
An overview of the rear panel is shown in Figure 1-3.
Figure 1-3: Rear Panel

IBX-660 Industrial Edge Storage Server
Page 5
1.6 Bottom Surface
WARNING:
Never remove the bottom access panel from the chassis while power is
still being fed into the system. Before removing the bottom access
panel, make sure the system has been turned off and all power
connectors unplugged.
The bottom surface of the IBX-660 contains the retention screw holes for the optional wall
mounting kit.
Figure 1-4: Bottom Surface

IBX-660 Industrial Edge Storage Server
Page 6
1.7 Hardware Specifications
The hardware specifications for the IBX-660 are listed below.
IBX-660
CPU (SoC) 22nm Intel® Atom™E3845 quad core processor (1.91 GHz)
Memory Slot 2 x 204-pin DDR3L SO-DIMM slots (system max. 8 GB)
*IBX-660-8G model is preinstalled with 8 GB (two 4 GB) memory
*For dual-DIMM configurations, you must use a pair of identical
DDR3L modules.
eMMC 32 GB
GPU 7th generation Intel® HD Graphics
Ethernet 2 x RJ-45 gigabit Ethernet port
HDD 4 x 2.5" SATA SSD/HDD
Display 1 x HDMI port (up to 1080p)
Audio 1 x Mic-in
1 x Audio out jack
USB 2 x USB 2.0 ports
2 x USB 3.0 ports
LED Indicators 1 x Status LED
1 x LAN LED
4 x HDD LED
Button 1 x Power button
Other Interface 1 x Kensington Security Slot
Fan Fanless design
Supported OS Microsoft Windows 10 IoT Enterprise / Linux

IBX-660 Industrial Edge Storage Server
Page 7
Power Supply Power 1: DC power jack, external power adaptor, 12 V, 90 W,
100 V–240 V input
Power 2: 4-pin terminal block, 9 V–36 V DC
Power Consumption 40 W (Intel®Atom® E3845 CPU with 8 GB 1600 MHz DDR3L
memory and four 2.5" HDD)
Operating Temperature -40ºC ~ 50ºC (-40°F ~ 122°F)
Please note that industrial SSDs are required to meet this condition.
Humidity 5%–95% RH non-condensing
Color Black
Mounting Wall mount with optional mounting kit
Weight Net weight: 1.11 kg (2.45 lbs)
Gross weight: 3.2 kg (7.05 lbs)
Dimensions 59 (H) x 180 (W) x 247 (D) mm
2.32 (H) x 7.09 (W) x 9.72 (D) inch
EMC FCC, CE
Table 1-2: Hardware Specifications

IBX-660 Industrial Edge Storage Server
Page 8
1.8 Dimensions
The dimensions of the IBX-660 are listed below and shown in Figure 1-5.
Figure 1-5: Dimensions (mm/inch)

IBX-660 Industrial Edge Storage Server
Page 9
Chapter
2
2 Unpacking

IBX-660 Industrial Edge Storage Server
Page 10
2.1 Unpacking
To unpack the IBX-660, follow the steps below:
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the system out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Make sure all the components listed in the packing list are present.
2.2 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do
not proceed with the installation. Contact the IEI reseller or vendor the
IBX-660 was purchased from o
r contact an IEI sales representative
directly by sending an email to [e-mail].
The IBX-660 is shipped with the following components:
Quantity Item Image
1 IBX-660 industrial edge storage
server

IBX-660 Industrial Edge Storage Server
Page 11
2 Ethernet cable
1 AC power adapter
1 Power cord
24 Flat head screws for HDD installation
Table 2-1: Package List
2.3 Optional Items
The following are optional components which may be separately purchased:
Item and Part Number Image
OS Image with Windows 10 IoT Enterprise Entry
64-bit for IBX-660 series, with DVD-ROM, RoHS
(P/N: IBX-660-W10E64-E-R10)

IBX-660 Industrial Edge Storage Server
Page 12
Chapter
3
3 Installation