IHT Cordynamic IDL707 User manual
IDL707
(WIFI)
i.h.t Smart Lock Installation Instruction
Please read this instruction carefully before installation
Installation
Safety Cautions
• It is recommended to look for a professionals to install.
• Please note that the connection power line can't be pressed or folded during installation.
• Before the installation, the lock must be positioned according to the door opening
direction. The handle can't be adjusted after lock body is installed .
• While installing, the door must be opened until the installation is completed. After the
installation is completed, test whether the front and back handle can unlock/lock using the
fingerprint, smart card, password (1234567890#) , APP and key.
• If it does not work properly, please check if there is an improper installation, if the power
cord is loose or the batteries are inserted incorrectly.
• Ensure no liquids are near the lock during installation.
Installation Overview
1. Front Panel
2. Connection Column
3. Square Steel
4. Lock Body
5. Connection power Line
6. Back Panel
7. Battery Cover
8. Connection Column Screws
9. Back Handle
10. Connection Column Screws
11. Latch-bolt
12. Dead-bolt
13. Lock Body Screws
14. Connection Column
15. Key Hole
16. Emergency Power Port
17. Front Handle
18. 'SET' Button
Features
5-Way Access Methods Fingerprint, Password, Card, APP, Back-up Key
Battery Type / Life 4×AA Battery / 1 Year
Storage Capacity 100 (Passwords, Fingerprints & Cards)
Identity Time 0.3 Seconds
Low Voltage Warning ≤4.6V
Privacy Password Random Numbers Can Be Added Before or After
Fire Rating 120 Minutes (AU 1530.4:2014)
1. Confirm The Direction of The Door
This smart lock is suitable for Left Out/Left In/Right Out/Right In installation. 4 kinds of door
opening orientations.
3. Installing the Open Hole
Please refer to the opening hole drawing and drill the correct holes on the door.
4. Installing the Body Lock
a. Choose the installation direction of the latch-bolt of the lock body by the door opening
directions. (Refer to the images above and below)
b. Changing the direction of lock body:
i. Push the reversing block upwards.
ii. Push the latch bolt into the body and twist
180 degrees.
iii. Release the latch bolt and push back down
the reversing block.
c. Put the lock body into the door frame and tighten 2
fixing screws.
Note:
• When releasing the latch bolt, ensure the centre anti
friction tongue is not caught in the body lock.
5. Selecting Hardware Parts
Choosesuitablepartsaccordingtothefollowingtable.
Door Thickness Square Steel
Length
Connection Column
Length
Connection Column
Screw Length
39.8-54.8mm 80.0mm 35.0mm 29.9 and 50.0mm
55.1-59.9mm 80.0mm 55.1mm 29.9 and 50.0mm
60.1-80.0mm 100.0mm 55.1mm 50.0 and 70.1mm
80.1-10.00mm 119.8mm 55.1mm 70.1 and 89.9mm
＞100mm (optional) 139.9mm 55.1mm 89.9 and 109.9mm
6. Installing the Lock
a. Install two connection columns into the front panel
b. Installing the front panel:
i. Insert the suitable square steel into the lock body.
ii. Pass the connection power line through the connection column screw hole.
iii. Align the square steel on the lock body with the square steel hole of the front panel
and fix the front panel onto the door by pressing the other end of the square steel.
c. Installing the back panel:
i. Press the front panel and connect the connection power line with the corresponding
interface on the back panel. Cable manage the remaining wires by inserting the
excess line into the door hole.
ii. Align the square steel on the body lock with the square steel hole of the back panel
and attach the back panel.
iii. Secure the door lock by screwing in the 2-connection column screws on the back
panel
7. Installing the Buckle Plate & Buckle Box
8. Post Installation Debugging
a. Always keep the door open when debugging.
b. Check whether the following functions can be achieved or not.
i. Press down the front handle, latch-bolt/dead-bolt remains still in locked
status.
ii. Press down the front handle, latch-bolt/dead-bolt retract when unlocked.
iii. Press down the back handle, latch-bolt/dead-bolt retract in any status.
iv. Lift up the front handle or back handle, dead-bolt stretches out in any
status.
c. Verify whether other functions are normal or not, including Self-locking, virtual
password, ‘Set’ button, Pickproof alarm, APP etc by referring to the user manual.
2. Changing Handle Direction
a. Front Handle Direction Change – Disassemble the direction
changing screw and twist the hand downwards 180 degrees
carefully and slowly. Once in position, screw the direction change
screw back on.
b. Back Handle Direction Change – Repeat the same operation as
above (step 2a).
c. Match the front handle and back handle and make sure they are
both orientated in the same direction.
