Assa Abloy Corbin Russwin FE6700 Series User manual

ASSA ABLOY, the global leader in door opening solutions
1
FM 327 08/17 (617419200)
FE6700 Series Multi-Point Lock
Installation Instructions for
Window Shutter Applications
Recommended Installation:
Install FE6700 so that the
deadbolt is equidistant from
the top and bottom of the
shutter.

ASSA ABLOY, the global leader in door opening solutions
2
This device is intended to be part of an integrated window shutter, frame and
hardware assembly UL-approved for both FEMA 361 and ICC 500 guidelines for
inswing window shutters. This instruction sheet will take you through the
following steps for full installation.
Table of Contents Page
Step 1 – Installation of Deadbolt Assembly ……………………………… 3
Step 2 – Installation of Bottom Bolt Assembly …………………………3&4
Step 3 – Installation of To p Pusher Assembly …………………………… 4
Step 4 – Aligning assemblies in preparation for drilling and pinning…5&6
Step 5 – Applying the Drill Jig for proper drilling ……………………… 7
Step 6 – Pinning the Rods to engage the Deadbolt Lever ……………….. 8
Step 7 – Installation of Inside and Outside Trim ………………………… 8
Step 8 – Installation of Cylinder in Outside Trim (Optional) …………… 9
Step 9 – Assemble the Top Latc h to the Frame …………………………... 9
Step 10 – Installation of Deadbolt Strike ………………………………… 10
Step 11 – Install the Bottom Strike ……………………………………… 10
Drill Guide for Deadbolt Case
Installation Jig Components

ASSA ABLOY, the global leader in door opening solutions
3
Step 1 – Installation of the Deadbolt Assembly
·Place the window shutter on a horizontal surface
with the pin lever notch located at the top of the
shutter facing up.
·The recommended deadbolt assembly location
should be equidistant from the top and bottom of
the shutter.
·Assemble the deadbolt case into the lock pocket
provided in the door. Note the orientation of the
lock, the top of the deadbolt case indicates that
this should be toward the top of the shutter.
·Assemble the lock to the edge of the shutter
using (2) 1/4 – 20 by 1" Flat Head Cap Screws.
Step 2 – Installation of the
Bottom Bolt Assembly
·Loosen the set screw so that the lifting platform will slide along
the lower rod tubing but not slide on its own when the rod is
held vertically. Be sure that the set screw is oriented so that it
will be accessible through the Lower Thru Bolt Cutout on the
top side of the shutter.
·When you insert the assembly into the shutter and through the
nylon guides of the deadbolt case this lifting pad will be in a
position to allow you to make the final necessary adjustment.
Note the orientation of the bottom bolt assembly the double
screw head side (not shown in this image) should be facing the
hinge side of the shutter.
Continue on next page………….
Set Screw
Lower Thru
Bolt Cutout

ASSA ABLOY, the global leader in door opening solutions
4
Step 2 – Installation of the
Bottom Bolt Assembly continued
·With the Deadbolt Retracted, slide the Bottom Bolt
Sub Assembly into the prep. hole in the bottom of the
shutter. As you guide the assembly up into the shutter
you will need to guide it into the bottom nylon guide of
the Deadbolt Assembly and then up thru the top nylon
guide.
·Seat the bottom bolt bracket against the shutters lower
reinforcement plate.
·Align Bottom Bolt Plate to shutter prep.
·Fasten the Bottom Bolt Assembly and Bottom Bolt Plate
to the bottom of the shutter using (2) 5/16-18 by 1" Flat
Head Cap Screws.
Nylon Guides
Step 3 – Installation of the
Top Pusher Assembly
·Slide this assembly into the prep. at the top of the
shutter, making sure the plunger pin is oriented with the
clearance slot on the stop side of the shutter.
·Visually align the rod of the Top Pusher Assembly so
that it enters the tube of the Bottom Bolt Assembly that
extends out of the Deadbolt Assembly.
·Align the Top Strike plate to shutter prep. Noting the
position of the beveled edge. It should be on the same
side as the plunger pin.
·Fasten the Top Strike plate and Top Pusher Assembly
to the top of the shutter using (2) 5/16-18 by 1" Flat
Head Cap Screws.
Top Pusher
Assembly
Plunger Pin
Strike Plate note
beveled edge position

ASSA ABLOY, the global leader in door opening solutions
5
Step 4 – Alignment of
components in preparation for
drilling and pinning
·Thread the Top Clamp into the
threaded hole so that it extends the top
latch to the proper position for pinning.
The Top Bolt Clamp will assure that
the top latch is in the correct position
for final installation.
·Prepare the lifting platform installation
jig by removing the two wing fasteners
and their washers
·Introduce the lifting platform jig up
through the under side of the shutter as
shown
·Using the two wing fasteners and their
washers, secure the lifting platform jig
to the shutter.
The lifting platform jig will now be in position
to allow sliding the lifting platform (shown in
step 2) so that it rests against the shelf of the
jig.
Continued on next page………….

ASSA ABLOY, the global leader in door opening solutions
6
Step 4 – Alignment of
components in preparation for
drilling and pinning continued
Before continuing to the next step be
certain the top pusher and bottom
bolt are in the correct position.
·Bottom Bolt should be flush to the
bottom of the shutter.
·The lifting platform (item 1) should be
moved down the bottom rod and placed
against the shelf of the lifting platform
jig.
·Next secure the platforms position by
tightening the cone point set screw
(item 2). This will assure the point on
the set screw embeds itself firmly into
the bottom rod.
12

ASSA ABLOY, the global leader in door opening solutions
7
Step 5 – Applying the drill jig
for proper drilling
·Manually project the deadbolt by
applying force to the deadbolt lever
toward the bottom of the shutter.
·The deadbolt lever is now in a position
to allow the Drill Guide to be
positioned above the deadbolt and fixed
into position using the two drill guide
positioning holes provided in both sides
of the deadbolt case.
·The Drill Guide is an alligator type jig.
Loosen the Drill Guides clamping
screw, allowing the jaws to rotate 90
degrees to allow the guide to be
positioned above the deadbolt and
closed around the shutter so that the
pins on both sides of the Drill Guide
engage the two Drill Guide Positioning
Holes.
·Once the Drill Guide is engaged in the
positioning holes, tighten the Drill
Guides clamping screw so that it will
firmly secure the jig around the shutter.
·Using the Drill Guide Hole, drill a 1/8"
hole (drill provided with Jig
Components) thru both sets of rods.
Deadbolt
Lever
Drill Guide
Positioning
Holes
Drill Guide clamping screw Drill Guide
Positioning
Pins
Drill Guide
Hole

ASSA ABLOY, the global leader in door opening solutions
8
Step 6 – Pinning the Rods to
engage the Deadbolt Lever
·Loosen the Drill Guides clamping
screw allowing the Drill Guide to be
removed from the shutter.
·Manually retract the Deadbolt by
applying force to the deadbolt lever
toward the top of the shutter.
·This will put the pinning hole in the
proper position for fastening the Drive
Pin.
·Insert the drive Pin from the underside
of the shutter and through the holes in
the rods and fasten the Drive Pin in
place with the spring Washer.
Hole shown in proper pinning
position.
Drive Pin.
The Lifting Platform Jig and the Top Clam p can now be removed from the shutter.
Step 7 – Installation of Inside
and Outside Trim
·Install the outside trim by inserting it
from underneath the shutter (outside
face).
·As it enters the shutter cavity the lifting
pad in the escutcheon will rest on the
underside of the lifting pad secured to
the rods in step 4.
·Press the outside escutcheon against the
shutter surface.
·Install the inside trim by placing it over
the shutter prep and positioning the
lifting pad of the inside trim on the
underside of the lifting pad.
·Visually align the mounting holes of the
inside escutcheon to the mounting posts
from the outside escutcheon.
·Insert 4 mounting screws ¼" – 20 by
1 ¾" and tighten screws.

ASSA ABLOY, the global leader in door opening solutions
9
Cylinder
Cylinder Collar
Cylinder Retaining Nut
Backplate
Outside Trim
Assembly
Step 8 – Installation of Cylinder in Outside Trim
(Optional)
·Insert the Cylinder into the
Cylinder Collar
·Place the Cylinder Retaining
Nut against the backplate of
the outside trim assembly,
·Feed the cylinder and
cylinder collar into the
cylinder hole of the
escutcheon and screw the
cylinder retaining nut to the
cylinder until it is fully
seated with the cam straight
up as shown.
·Secure the cylinder to the
escutcheon by tightening the
cylinder retaining nut.
Step 9 – Assemble the Top Latch to the
Frame
·Assembly the top latch into the top of the frame using (4)
¼" – 20 by 1" Flat Head Cap Screws. The angled surface
should face the shutter.

ASSA ABLOY, the global leader in door opening solutions
10
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
Deadbolt Strike
Step 10 – Installation of Deadbolt Strike
·Assemble the Deadbolt Strike to the frame using
(2)¼"–20by1"FlatHeadCapScrews.
Step 11 – Install the Bottom Strike
·Place the Bottom Strike into the Strike Shim and
fasten to the frame using (2) ¼" – 20 Screws
Install the Shutter into the frame assembly and shim for proper shutter
gap and for the shutter being square and plumb
END OF INSTALLATION INSTRUCTIONS
Bottom Strike
Strike Shim
In U.S.A.: In Canada:
Corbin Russwin, Inc. ASSA ABLOY Door Security Solutions Canada
225 Episcopal Road 160 Four Valley Drive
Berlin, CT 06037 USA Vaughn, Ontario, Canada L4K 4T9
www.corbinrusswin.com www.assaabloy.ca
Technical Product Support:
Telephone: [phone]
Fax: [phone]
ASSA ABLOY is the global leader in door opening solutions, dedicated to
satisfying end-user needs for security, safety and convenience.
END