Ikan PT4900-PEDESTAL User manual

www.ikancorp.com | 1.713.272.8822 | [email protected]
PT4900-PEDESTAL
Quick Start Guide
19” Teleprompter, Pedestal & Dolly Turnkey
OVERVIEW
Ikan’s Turnkey Broadcast Solutions include everything you need for your professional camera setup. This solution includes a 19” teleprompter,
pedestal, and dolly. All of our systems have been tested internally for payload compatibility.
The remaining payload capacity, after mounting the full 19” teleprompter, can accommodate camera setups up to 30.8 lbs. The pedestal,
without the teleprompter system, can accommodate cameras up to 61.7 lbs. This solution also includes a hard case for the pedestal and a
carrying bag for the dolly.

www.ikancorp.com | 1.713.272.8822 | [email protected]
What’s Included
Large Riser
Bottom Plate
Hood Attachment Frame
Glass Frame Screws 15mm Rod Clamps 15mm Rods Large Riser
Bracket
Glass Holder Hood
Glass
Medium Riser
Base
DSLR/Mirrorless Riser
Glass Frame Holder Bracket
w/ Rod Clamps
PT4900
19” Professional High Bright Beam Splitter Teleprompter

www.ikancorp.com | 1.713.272.8822 | [email protected]
Teleprompter Assmebly Setup
Step 1
Place the Hood Attachment Frame over the Glass Holder. Then place the
glass against the Glass Holder. Make sure the screws pass through the
holes on the both the Hood Attachment Frame and the Glass Holder.
Step 3
Remove the monitor mounts from the teleprompter base using
the included larger 4mm hex key to loosen from the 15mm rods.
Step 4
Put the washers on before tightening the screws. The washers and 4
additional screws are inside a bag on the bottom foam.
Step 2
Secure the Glass Holder by fastening the knurled nuts to the screws as
pictured below.
1
2
-
2
4
V
H
D
M
I
V
G
A
AV

www.ikancorp.com | 1.713.272.8822 | [email protected]
Step 5
After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket.
Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor.
*SAFETY NOTE* Make sure to leave at least 2 inches of the rods inside the teleprompter base.
Teleprompter Base
Step 6
While sliding the teleprompter bracket into the slot of the Glass Frame
Holder Bracket, pull on the red knob to allow the bracket to fully slide in.
Step 7
Once the bracket is in place, tighten the side screw to lock in place.
Double check and make sure all the screws are tightened with the
included hex keys.

www.ikancorp.com | 1.713.272.8822 | [email protected]
Step 9
To prevent light from leaking through the hood, seal both zippers down.
Step 8
Fold the flaps of the Hood alongside the edges of the Hood Attachment Frame. The flaps of the Hood are magnetic so they will automatically attach.

www.ikancorp.com | 1.713.272.8822 | [email protected]
Step 10
Slide in the Riser plate of your choice by aligning the screws on the riser plate to the slot on the Base. Once the screws are aligned, Slide the riser plate into
the Base.
Step 10
Slide in the Riser plate of your choice by aligning the screws on the riser plate to the slot on the Base. Once the screws are aligned, Slide the riser plate into
the Base.

www.ikancorp.com | 1.713.272.8822 | [email protected]
Step 12
Mount your own tripod plate to the bottom plate by aligning the 1/4-20 and/or 3/8-16 screws and fastening them to the Bottom Plate. It is recommended
that you connect your tripod plate to front of the Bottom Plate so that you can balance your teleprompter easier. Once your tripod plate is connected to the
Bottom Plate, mount the tripod plate to your tripod head.
Step 13
Slide the entire teleprompter system into the Bottom Plate. Once the
teleprompter system is inserted, you can balance it by sliding it along the
Bottom Plate until the center of gravity is determined.
Step 14
Once the center of gravity has been determined, tighten the thumb screws
to keep the base from sliding.

www.ikancorp.com | 1.713.272.8822 | [email protected]
Step 15
To secure your teleprompter system, insert the included headless screws into the threads behind and in front of the Base.
Step 16
The headless screws should be inserted to the threads as pictured below.

www.ikancorp.com | 1.713.272.8822 | [email protected]
Monitor Ports
3G-SDI – Serial Digital Interface Connection
VGA – Video Graphics Array DE15 Connection
HDMI – High-Definition Multimedia Interface Input Connection
Power Port – 12-24v Input
HDMI – Switch HDMI input
VGA – Switch to VGA input
SDI – Switch to 3G-SDI input
Flip – Toggle image flip
(Can be set to horizontal, vertical, or both via menu)
Up Arrow – Toggle up to adjust setting
Menu – Access to monitor settings
Down Arrow – Toggle down to adjust setting
Monitor Menu Settings
Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup – Manually configure RGB
Return
System Config
Menu Duration – Set duration of how long menu stays
on screen
Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is
native resolution, 16:9 will create black bars)
Flip-H – Assign toggle button to flip image horizontally
Flip-V – Assign toggle button to flip image vertically
Reset – Factory reset
Return
PC Setup (Only available for VGA)
H-Position – Adjust horizontal position
V-Position – Adjust vertical position
Auto – Monitor automatically adjust position
Return
Exit
H
D
M
I
How to set-up FLIP button feature:
1. Press MENU button
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H
4. Change FLIP-V and/or FLIP-H to “ON”
5. Exit MENU
6. The FLIP button should now be activated and can be
pressed to mirror the image Horizontally or Vertically
7. When FLIP-H is ON, the image will flip Horizontally
8. When FLIP-V is ON, the image will flip Vertically
9. If both are ON, the FLIP button will toggle both
Horizontal and Vertical flip

www.ikancorp.com | 1.713.272.8822 | [email protected]
Specifications
PT4900-SDI
Optional Accessories
PT4900-GM
PT19-SDI-TM
PT-PEDAL
PT-CASE-V2
Replacement Glass for PT4900
19” 3G-SDI Talent Monitor Add On Kit for PT4900
Teleprompter Foot Control Pedal
Rolling Hard Case for PT4900 Teleprompter
Aspect Ratio 4:3
Backlight LED
Brightness 1000 nits
Build Material Aluminum Chassis
Diagonal 19”
Input Signal 3G-SDI, HDMI, and VGA inputs
Input Voltage DC 12v / 4A
Power Consumption 10W
Reading Range 25’
Resolution 1280 x 1024
Viewing Angle 160° (H) / 170° (V)
Weight 33.75 lbs
Shipping Weight 36 lbs
Shipping Dimensions 25 x 20 x 16 in
Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Telepromopters:
https://youtube.com/playlist?list=PLcjaK5n9Y8ctrbYS3t2g4nyx2uADOXjuF