Ikegami HLM-905WR User manual

㩷
㩷
㩷
MODEL
HLM-905WR
㩷
MULTI FORMAT
LCD COLOR MONITOR
㩷
㩷
㩷
㩷
㩷
OPERATION MANUAL
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷

㩷

i
SA 1966 SA 1965
CAUTION
SA 1965
The lightning flash with arrowhead inside a triangle is intended to warn the user that
parts inside the product are dangerous and many cause electric hazards.㩷
SA 1966
The exclamation mark inside a triangle is intended to inform users that important
operating and servicing instructions are provided with the equipment.㩷
WARNING: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COMPONENTS ONLY WITH
MANUFACTURE’S RECOMMENDED PARTS (REFER TO SERVICE LITERATURE).
DECLARATION of CONFORMITY:
The “CE” mark means the products as mentioned below will meet the intent of the following Directives and Standards.
Inrush current according to EN55103-1 Annex B is as follows.
HLM-905WR : 0.117A r.m.s. (the average half-cycle r.m.s. inrush current, on initial switch-on.)
: 0.112A r.m.s. (the average half-cycle r.m.s. inrush current after a supply interruption of 5 s.)
Directives : 93/68/EEC, 2004/108/EC, 92/31/EEC for EMC (electromagnetic compatibility)
2006/95/EC for Low voltage (Safety)
Standards : HLM-905WR : EN55103-1-E4, EN55103-2-E4, EN60950-1
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR WATER.
Disposal of used Electric and Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product, or in the related documents in the package, indicates that this product shall not be
treated as normal household waste. Instead, it should be taken to a proper applicable collection point or depot
for the recycling of electric and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials
will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city authority, your household waste
disposal service or the place where you purchased the product.
RISK OF ELECTRIC SHOCK
DO NOT OPEN.
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
CAUTION;
ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PART RESPONSIBLE
FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.

ii
IMPORTANT SAFETY INSTRUCTIONS
1. General
1) Read all instructions provided.
2) Save these instructions for future use.
3) Follow all warnings and instructions marked on
the television equipment.
4) Never insert objects of any kind into this
television monitor through cabinet slots as they
may come in contact with dangerous voltage
points or short out parts, resulting in fire or
electric hazards, Never spill liquid of any kind on
the television monitor.
5) Do not attempt to service this television monitor
yourself as operating or removing covers many
expose you to dangerous voltage or other hazards,
Refer all servicing to qualified service personnel.
6) Do not use attachments not recommended by the
television equipment manufacturer as they may
result in the risk of fire, electric shock, or injury to
persons.
7) This television monitor has been preadjusted to
meet the respective broadcasting standard signals.
So, it cannot be used with the signals of different
broadcasting standards.
8) When keeping or transporting the unit for a long
time, pack it in the supplied carton or equivalent.
2. Power supply
1) This television equipment should be operated only
from the type of power source indicated on the
marking label.
2) This television equipment is provided with a
three-wire grounding type plug with a third
(grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into
the outlet, contact your electrician to replace your
obsolete outlet.
Do not defeat the safety purpose of the
grounding-type plug.
3) When connecting and disconnecting the power
cable, be sure to hold the plug.
4) Do not allow anything to rest on the power cord.
Do not place this television equipment where the
cord will be abused by persons walking on it.
5) For added protection for this television equipment
during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet.
This will prevent damage to the equipment due to
lightning and power-line surges.
6) Do not overload wall outlets and extension cords
as this can result in fire or electric shock.
3. Usage and location
1) Do not use this television equipment near water -
for example, near a bath tub, kitchen sink, or
laundry tub, in a wet basement, or near a
swimming pool, or the like.
2) Do not place this television equipment on an
unstable cart, stand, or table. The television
equipment may fall, causing serious injury to
children and adults, and serious damage to the
equipment. Use only with a cart or stand
recommended by the manufacture, or sold with
the television equipment. Wall or shelf mounting
should follow the manufacture’s instructions, and
should use a mounting kit approved by the
manufacture.
Television equipment
and cart combination
should be moved with
care. Quick stops,
excessive force, and
uneven surfaces may
cause the equipment
and cart combination to overturn.
3) Slots and openings in the cabinet and the back or
bottom are provided for vitiation, and to ensure
reliable operation of the monitor and to protect it
from overheating, these openings should never be
blocked or covered. The openings should never be
blocked by placing the television equipment on a
bed, sofa, rug, or other similar surface. (This
television equipment should never be placed near
or over a radiator or heat register.) This television
equipment monitor should not be placed in a
built-in installation such as a bookcase unless
proper ventilation is provided.

iii
IMPORTANT SAFETY INSTRUCTIONS
4) Avoid operating or placing (keeping) in a hot (+40
or over) or cold (less than 0), high vibration, or
dusty place. Avoid operating or storing in a place
exposed to direct sunlight.
5) If an image of extremely high brightness is
displayed on the screen for a long time, the panel
may get burned in.
4. Cleaning
1) Unplug this television equipment from the wall
outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
2) Do not use thinner or benzene for cleaning.
Otherwise, the cabinet may deform or the paint
may peel away.
5. Repair
1) Unplug this television monitor from the wall
outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged or
frayed.
b. If liquid has been spilled into the television.
c. If the television monitor has been exposed to
rain or water.
d. If the television does not operate normally by
following the operating instructions.
Adjust only those controls that are covered by
the operating instructions as improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the
television monitor to normal operation.
e. If the television monitor has been dropped or
the cabinet has been damaged.
f. When the monitor exhibits a distinct change in
performance - this indicates a need for service.
2) When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacture that have the same
characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
3) Upon completion of any service or repairs to this
monitor, ask the service technician to perform
routine safety checks to determine that the
television is in safe operating condition.
4) For repair service, contact Ikegami’s authorized
sales representative or Ikegami service desk
directly.

iv
PRECAUTIONS FOR OPERATIONS
1) Never let this unit fall or subject it to strong
shock.
2) Do not remove the cabinet unless necessary.
High-voltage parts are contained in the cabinet
and they are very dangerous if you touch then.
Only qualified service engineers are allowed to
adjust the internal parts of the cabinet.
3) This color monitor has been adjusted to signals
conforming to each broadcasting standard.
It cannot be used for signals of different
broadcasting standards.
Be sure to operate the color monitor within the
voltage range marked on its back.
4) If cabinet or screen is dirty, wipe with soft cloth.
At this time, avoid using benzene or thinner,
otherwise the paint may peel away.
5) Note that, if video signals with high luminance
are monitored on the LCD panel over a long
period of time, the panel may burn in the image.
6) The socket-outlet shall be installed near the
equipment and shall be easily accessible.
7) Avoid using or storing this unit in the following
places:
࡮Hot (+40or more) or cold (0or less)
places, especially where this unit may be
exposed to the direct rays of the sun.
࡮Humid and dusty places.
࡮Places where there is considerable vibration.
࡮Places exposed to rain or water.
࡮When storing or transporting this unit, pack it
in the supplied carton or equivalent.
8) If no image can be monitored even after
performing user adjustment or the unit appears
faulty, do not dismantle this unit by yourself. In
such cases, contact the Ikegami service desk.
9) Should this unit fail within one year after delivery,
it will be repaired free of charge unless the
malfunction was caused by mishandling or misuse
of the user.
However, the fuses are not covered by the
warranty.
10) The specifications and appearance of this unit
may be subject to change for further improvement
without prior notice.
Cautions for Rack-Mount.
A) Elevated Operating Ambient - If installed in a
closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment
may be greater than room ambient. Therefore,
consideration should be given to installing the
equipment in an environment compatible with the
maximum ambient temperature (Tma) specified
by the manufacturer.
B) Reduced Air Flow - Installation of the
equipment in a rack should be such that the
amount of air flow required for safe operation of
the equipment is not compromised.
C) Mechanical Loading - Mounting of the
equipment in the rack should be such that a
hazardous condition is not achieved due to uneven
mechanical loading.
D) Circuit Overloading - Consideration should be
given to the connection of the equipment to the
supply circuit and the effect that overloading of
the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used
when addressing this concern.
E) Reliable Earthing - Reliable earthing of
rack-mounted equipment should be maintained.
Particular attention should be given to supply
connections other than direct connections to the
branch circuit (e.g. use of power strips).

v
Precautions Upon Use
In order to use the monitor safely, read through this
manual and pay attention to the following points in
particular.
1. Do not use any power supply other than the specified
one (AC/DC).
2. Do not give a shock to the monitor.
Be very careful to keep the monitor from shocks because
glass is used inside the LCD.
3. Do not use or store the monitor in the following places.
Place where the ambient temperature is out of spec
When installing the monitor on a monitor shelf, switcher
table, rack, etc., make sure in advance that the
temperature of the installation location is within the
specified range.
In the case of an outdoor setup, even if the ambient
temperature is within the specified range, the inside of
the monitor may be heated by direct sunlight. Therefore,
keep radiation in mind. (Avoid direct sunlight.)
Never block the air outlet at the rear of the monitor and
the air inlet at the side. Make sure in particular that a
blackout curtain or the like does not block the air outlet.
Place exposed to rain, snow or high humidity
Use of the monitor in such a place will cause electric
leakage or failure.
4. Avoid exposing the LCD screen to direct sunlight.
Exposure of the LCD screen to direct sunlight for a long
time will degrade the film. Therefore be careful of direct
sunlight when using the monitor outdoors.
5. Cautions in handling the front LCD panel
Be careful not to touch the LCD panel front surface with
bare hands, unless necessary. When wiping the dust off
the surface, use soft, dry cloth and take care not to rub
the surface strongly. Do not use thinner or benzene.
6. Do not touch liquid crystal leaked from the monitor's
display surface.
If the monitor's display surface is accidentally broken
and the liquid crystal leaks, be careful never to put the
liquid in your mouth, inhale it and allow it on your skin.
If the liquid gets into your eye or mouth, immediately
rinse it with water and get medical attention.
If the liquid contacts your skin or clothes, immediately
wipe it off using alcohol or the like and wash the stained
spot with soap and water. Do not leave the liquid intact,
because otherwise your skin or clothes may be affected.
7. Do not display the same pattern for a long time.
Note that residual image may be generated if the same
pattern is displayed for a long time.
࡮Turn off the power when the monitor is not used.
To avoid residual images, preferably take the following
measures.
࡮Change the screen regularly.
࡮Display the whole screen in white.
8. Caution for condensing.
When the monitor is used in the condition where
temperature abruptly changes, the surface of LCD panel
and the inside of monitor are possible to get condensed.
And if it is used leaving condensed, it can cause
deterioration of quality and trouble.
If the device is condensed, please do not turn on the
power until waterdrop is disappeared completely.
9. Avoid operation or storage in a place exposed to
corrosive gas.
Operation or storage in a place where any corrosive gas
such as sulfur dioxide, hydrogen sulfide, chlorine or
ammonia is generated may lead to a significant
reduction in the monitor service life. It may also cause
failure or electric leakage.
Also avoid using the monitor in a location exposed to
high salty wind.
10. Do not use this monitor for such applications as space
appliance, nuclear control system as any medical
equipment involving human life.

vi
Quality of LCD panel
Note that because the LCD panel mounted on the
monitor is manufactured through the use of
high-precision technology, 99.99% or more of the pixels
are effective, but 0.01% or less of them may be lacking in
brightness or lit up constantly.
Internal fan
The internal fan does not run constantly but
automatically starts running when the internal
temperature of the monitor rises. When the
environmental temperature is low, the internal fan may
not be running, which indicates no fault condition.
At power-on, the fan rotates for a moment for checking
its own performance.
In the case of outdoor use, even if the ambient
temperature is low, the fan may start running when the
internal temperature of the monitor rises.
Suppose that the fan does not operate properly at
power-on or at high temperatures. In such case, the
message "FAN ERROR!" will appear at the top of the
screen.
The brightness of the backlight may be reduced in order
to keep the internal temperature of the motor from
rising.
If the message "FAN ERROR!" is displayed, contact your
dealer or Ikegami service desk.
Warranty
If the product should fail within one year from the date
of delivery in spite of the proper use, the manufacturer
will repair the product free of charge. Even if the
product is covered by the warranty, however, the
customer will be charged for labor and parts in the
following cases.
1. Failure and damage caused by the following:
࡮Improper use
࡮Repair or modification performed by the customer
࡮Transportation, transfer, falling, etc. after the
purchase of the product
࡮External factors such as natural disasters and
over-voltage
2. Aged deterioration of the liquid crystal panel and
backlight (change in brightness, increase in the
number of luminescent spots and dark points, etc.)
3. Damage, discoloration and degradation of the
cabinet including the LCD front protective panel
4. Replacement of the accessories and fuse
If no image comes out in spite of routine adjustment
or if the product should seem to fail, contact your
dealer or Ikegami service desk.
Accessories
The monitor comes with the following accessories. Be
sure that they are included.
1. Operation manual: 1 copy
2. Parallel remote connector: 1 set
3. Power cable: 1 pc.
Specifications and external dimensions are subject to
change without prior notice.

㩷
㩷
CONTENTS
㩷
IMPORTANT SAFETY INSTRUCTIONS
PRECAUTIONS FOR OPERATIONS
Cautions for Rack-Mount.
Precautions Upon Use
For the first-time use afterpurchase
1. Outline........................................................................ 1
1-1. Outline ............................................................. 1
1-2. Features .......................................................... 1
2. Names of parts and their Functions..................... 4
2-1. Front Controller Parts............................... 4
2-2. Rear panel (left)............................................ 7
2-3. Rear panel (video inputs/outputs).......... 8
3. Markers...................................................................... 9
3-1. Types of Markers ....................................... 9
4. MENU Functions .................................................... 10
4-1. List of MENU................................................. 10
4-2. Flow of MENU Operations....................... 13
4-3. Description of MENU 1 Functions........ 16
4-4. Description of MENU 2 Functions........ 17
4-5. Description of MENU 3 Functions........ 20
4-6. Description of MENU 4 Functions........ 22
4-7. Description of MENU 5 Functions........ 27
4-8. Description of MENU 6 Functions........ 28
4-9. Description of MENU 7 Functions........ 31
4-10. Description of MENU 7
(USER MARKER) Functions and Making
Settings............................................................ 33
4-11. Description of MENU 8 Functions........ 37
4-12. Description of MENU 9 Functions........ 38
4-13. Description of MENU 10 Functions...... 38
4-14. Description of MENU 11 Functions...... 39
4-15. Description of MENU 12 Functions...... 44
4-16. Description of MENU 13 Functions...... 47
5. Preset Menu Function............................................. 50
5-1 List of preset menu ..................................... 50
5-2 Description of preset menu ..................... 50
5-2-ԘSelection of files ..................................... 50
5-2-ԙChange of preset data .......................... 51
5-2-ԚDisplay of preset data list................... 52
5-2-ԛCopying of file data............................... 52
5-2-ԜSetting of file change operation
at the time of channel change........... 52
5-2-ԝSetting of data protection
password................................................... 52
5-2-ԞOperation of Auto Setup ..................... 53
5-2-ԟSetting the backlight brightness
level............................................................. 53
6. Mouse menu function............................................. 54
6-1. Basic procedure of the mouse menu .... 54
6-2. Basic procedures on the MENU and PRESET
MENU screens............................................... 55
7. Specifications ......................................................... 56
7-1. General specifications ............................... 56
7-2. Rated performance ..................................... 56
7-3. Specifications for liquid crystal display (LCD)
module ............................................................. 57
7-4. Functions ........................................................ 58
7-5. Remote control ............................................. 59
8. Applicable Standards............................................ 59
8-1. Safety standards .......................................... 59
8-2. Electromagnetic interference................. 59
8-3. Environmental regulations...................... 59
9. Options........................................................................ 60
10. External View ........................................................... 62
(1) Option (main chassis)................................. 62
(2) Option (STD-900,BB-904V,PP-904) ........ 63
(3) Option (STD-900,BB-904A,PP-904) ........ 63
(4) Option (STD-920T,BB-904V,PP-904)...... 64
(5) Option (DR-904)............................................ 64
(6) Option (AT-900)............................................. 65
Data 1 Parallel Remote Pin Function......................... 66
Data 2 Control with Remote Controller..................... 68
Data 3 Rs-485 Pin Function......................................... 68


㩷

- 1 -
HLM-905WR Multi-Format LCD Color Monitor
1
㧚
Outline
㩷
1-1
㧚
Outline
This 9-inch type HDTV/SDTV multi-format
color monitor employs a high-definition liquid
crystal panel for reduction in thickness, weight
and power consumption, and is designed for use
in various spaces such as sub-control rooms, ed-
iting rooms, monitor wall, transmission control
desks, and outside broadcast vans.
This monitor is compatible with the functions
and operation of the HTM/TM series CRT moni-
tors, so that it can realize the functions necessary
for a broadcasting service monitor with conven-
tional operation.
㩷
1-2
㧚
Features
(1) High performance liquid crystal panel
Employed is a liquid crystal panel with a
WXGA (1280 x 768 dots) that is excellent in basic
performances such as high brightness, high con-
trast, wide viewing angle, quick response and
good color reproducibility.
㩷
(2) Multi-format
The monitor supports various broadcasting
formats.
࡮480i/59.94 (NTSC) ࡮1035i/60, 59.94
࡮575i/50 (PAL-B) ࡮1080i/60, 59.94
࡮1080psF/30 ࡮1080i/50
࡮1080psF/25 ࡮720p/60, 59.94
࡮1080psF/24, 23.98 ࡮720p/50
࡮1080p/60, 59.94 ࡮720p/30, 29.97
࡮1080p/50 ࡮720p/24, 23.98
࡮1080p/30, 29.97 ࡮720p/25
࡮1080p/25
࡮1080p/24, 23.98
(3) Compatibility with embedded audio
Standard equipped with an embedded audio
feature, the embedded audio signals multiplexed
with 3G-SDI signal, HD-SDI signal or SD-SDI
(4:2:2) signal can be automatically recognized and
the audio output can be heard through the
built-in speaker, stereo headphones and audio
monitor output. The monitor also has a standard
embedded audio level meter display on the screen.
The embedded audio signal may be handled as
an analog output.
(4) Remote control functions
The monitor can be remote-controlled with the
use of three remote control functions. Depending
on the place of installation and type of operation,
the parallel, serial mode can be used.
In addition to the conventional parallel remote
control (pin assignment by user is possible), the
monitor also comes standard with a serial remote
input interface that enables remote control with
just one BNC coaxial cable.
Up to 99 monitors can be remote-controlled in-
dividually or concurrently using an optional serial
remote controller (during next model examina-
tion) simply with Ikagami’s various monitors be-
ing loop-through connected.
(5) Built-in markers
4:3 (16:9 mode), 13:9, 14:9, 15:9, 16:9 (4:3 mode),
1.85:1 (16:9 mode) and 2.35:1 (16:9 mode) line
markers can be displayed.
The monitor can also get the 1%-stepwise
safety marker displayed in the range of 80-99%
with respect to the line marker area.
The safety markers over the effective screen
can be equally preset 1% by 1% in the range of
80-99%.
The monitor also comes standard abundantly
with five-part split and ten-part split crosshatch
markers useful for location alignment.
(6) User marker display function
Up to 10 different user markers, such as line
and box markers, are presettable pixel by pixel to
your desired positions and sizes. The line and box
drawing settings can be easily made with not just
the switch but also the USB mouse. Resulting
complicated data may also be saved on a USB
memory so that the data can be copied to another
monitor or stored in a PC.
This function is optimum for positioning in ed-
iting the layout and its display for various types
of information such as teleshopping.
* Patent pending

- 2 -
(7) Shadow function
The shadow function is to shade the area other
than a 4:3 (16:9 mode), 13:9, 14:9, 15:9 or 16:9 (4:3
mode) marker area on images. The shadow con-
trast can be set at 0%, 20%, 40% or 60% on the
MENU. The use of this function allows you to
instantly visualize the image area when convert-
ing images with an aspect ratio of 16:9 to those
with an aspect ratio of 4:3 or vice versa.
This shadow function can be turned on/off by
remote control and prompt switching is therefore
realized.
(8) Various built-in test signals
The monitor is standard equipped with color
bar signal, grayscale signal with pluge pattern,
and window signal. Various adjustments can
therefore be made on the monitor alone.
(9) Time code display function
It is possible to display the time code (VITC)
multiplexed into SDI signal on the screen.
The display comes in two sizes, large and small,
and its brightness in three levels.
(10) Waveform monitor/Vector scope display func-
tions
Waveform monitor of brightness signal can be
displayed. The display comes in two sizes,
NORMAL and SMALL, and its brightness in
three levels. The waveform can also be displayed
in any of three selectable positions and in one of
two colors: GREEN and WHITE. The vector scope
can also be readily displayed.
(11) Display comparison function by using 2 split
screens or by switching between 2 full screens
Comparison of images is possible by displaying
a previously captured still image and the cur-
rently input moving image simultaneous side by
side on the split screen basis, or by manually or
automatically switching between the still image
and the moving image on the full screen basis.
This function is useful for making adjustments
between a number of cameras and for positional
alignment.
As it allows storing up to 32 captured images
on a USB memory, this function can be used for
making adjustments of colors and positions be-
tween a single captured image downloaded from
the USB and the current image on the camera.
(12) Dot-by-dot display function
All the picture elements of an input signal are
displayed 1:1 according to the pixels of the LCD
panel without scaling the incoming signal
(enlarging or reducing the input signal according
to the LCD pixels).
This function is useful in checking transmitted
input signals for pixel defects, camera CCD’s
scratches, etc.
(13) External memory function
Various data (including the MENU settings,
the PRESET data, and the full capture image
data) can be stored on the USB memory for data
management on the PC. All these data can be
copied onto another monitor.
* In case the data is to be copied onto another
monitor, care should be taken as the PRESET
data on individual monitors are different in
their data types.
The data type of the stored images is in the spe-
cific format exclusive to the device used.
(14) USB mouse control
By connecting a commercially available USB
mouse to the USB terminal of this monitor, it is
possible to perform various adjustments including
the “MENU setting,” “PRESET data setting,”
“Input signal switching,” and the “Front switch
setting” through the use of a mouse. Remote
operation of the monitor at a distant position is
possible by using a commercially available wire-
less mouse.
Use of the scroll wheel function of the mouse
has significantly improved the user-friendliness
of the monitor for making adjustment of various
data such as color temperature.
(15) AC/DC operation
The monitor can accept the AC/DC power as
standard. Use of a battery is optionally possible.
This monitor is not of the external AC adapter
type but of the all-in-one construction that allows
direct AC input to the main body of the monitor.
When a rack mount is used, therefore no extra
space other than that for the main body of the
monitor is required.

- 3 -
(16) Downmix function
Among the embedded audio 8 channels, 5.1
channel surround audio channel (Lm, Rm, C, Ls,
and Rs) has been selected for the stereophonic
audio function at the downmix mixing ratio
specified by ARIB and ISO/IEC.
The downmix audio signals can be easily out-
put through the speakers built in the monitor or a
headphone, or through the analog output.
(17) Auto Setup Function for Color Temperature
The color temperature, which was difficult to
adjust before is simply and automatically ad-
justable in each steps without PC, connecting this
ASP-100 Auto Setup Prove to the USB port on
monitors.
And it is also able to be used as the measuring
instrument for measuring color temperature
(color point of x, y) and contrast.
* HLM-905WR supports in more than ASP-100
Rev1.
(18) IMD/UMD display by TSL protocol
This is a function to control the IMD/UMD
display in a centralized manner by using “TSL
UMD Protocol V3.1.
For displaying, Material Display (alphanumeric)
and TALLY Display are possible.
A maximum of 32 units per line (system) can be
controlled in a centralized manner by using
RS485.
By increasing the number of lines, the ID
setting and individual controls of a maximum of
126 units become possible.
* IMD㧦In Monitor Display
UMD㧦Under Monitor Display
(19) IMD/UMD display by the user display
This is a function for specifying the name of
material at random by using up to 8
alphanumeric letters on individual monitors for
each of the inputs (SDI-A/SDI-B/VBS) to indicate
the name of the material that has been specified
in advance in monitor display or under monitor
display when the input channel is switched over.

- 4 -
2
㧚
Names of parts and their Functions
㩷
2-1
㧚
Front Controller Parts
㩷
㩷
㩷
Ԙ
POWER switch
࡮This switch is used to turn ON/OFF the monitor.
* This switch will not turn ON/OFF the AC power
supply for the monitor.
* It takes several seconds for an image to come up
after power-on.
ԙ
POWER LED
࡮This LED is lit up in green when the power supply
for the monitor is ON.
* When running on battery,this LED indicator
starts flickering to tell you the remaining battery
power becomes low. In such case, immediately
turn off the power and replace the battery with
new one. When the remaining battery power gets
to the lower limit, the power is forced to shut off
and the LED indicator starts flickering at 0.5 sec.
intervals after alarm is issued for 30 sec. (the
LED flickering is quicken for about 30 sec.)
* When using a battery, set the nominal voltage on
the menu appropriately in accordance with the
battery to be used. For the setting item, refer to
4-4. Description of MENU 2 Functions
Ԣ
.
㩷
Ԛ
MENU/ENT switch
࡮This switch is pressed to display the menu screen
and to change the menu screen.
࡮This switch is also pressed to confirm entries on
the menu.
ԛ
PRESET switch
࡮This switch is pressed to display the preset menu.
* This switch is ineffective when the menu isdis-
played.
㩷
Ԝ
ESC switch
࡮This switch is pressed to escape from menu op-
eration.
ԝ
VBS switch/(LEFT) switch
࡮To select the VBS input, this switch is pressed
with the menu and preset menu not displayed.
࡮When the menu or preset menu is displayed, this
switch is used to select setting items on each
menu.
Ԟ
SDI (TST)switch/(RIGHT) switch
࡮To select the SDI input, this switch is pressed with
the menu and preset menu not displayed.
࡮To display the incorporated test signal, this
switch is pressed and held for several seconds
with the menu and preset menu not displayed.
࡮When the menu or preset menu is displayed, this
switch is used to select setting items on each
menu.
ԟ
CH SELECT
switch/ (UP)/ (DOWN)
switch
࡮To select channels when the SDI input is selected,
this switch is pressed with the menu and preset
menu not displayed.
࡮When the menu or preset menu is displayed, this
switch is used to change the setting of each item.
࡮When the internal test signal is displayed, this
switch is used to change the type of test signal.
࡮The following three types of test signals are in-
corporated.
ࡊ࡞࡯ࠫࡘઃ߈㓏Ბᵄ
0%
+2%-2%
0%㨪100%
㓏Ბᵄ
ࠞ࡜࡯ࡃ࡯
100%࠙ࠖࡦ࠼࠙
<100% Window>
<Color Bar>
<Staircase wave with pluge>
0-100%
Staircase
wave
㪜㪪㪚
㪧㪩㪜㪪㪜㪫㪤㪜㪥㪬㪆㪜㪥㪫 㪠㪥㪧㪬㪫
㪭㪙㪪
㪲㪫㪪㪫㪴
㪪㪛㪠
㪘
㪙
㪝㪈
㪝㪉
㪘㪪㪧㪜㪚㪫 㪪㪚㪘㪥
㪤㪦㪥㪦 㪤㪘㪩㪢
㪚㪟㪩㪦㪤㪘 㪙㪩㪠㪞㪟㪫 㪚㪦㪥㪫 㪘㪬㪛㪠㪦
㽲㩷
㽳㩷 㽴㩷 㽵㩷 㽸㩷 㽻㩷 㽽 㽾
㽶㩷 㽷㩷 㽹㩷 㽺㩷 㾀㾁㾂㾃㾄㾅㩷
㽼㩷 㽿 ٤
21 ٤
22

- 5 -
Ԡ
CH-B LED
࡮This LED is lit up when CH-B is selected in the
case of the SDI input.
* When the internal test signal is displayed, this
LED is not lit up at any time.
㩷
ԡ
F1 switch
࡮It becomes possible to perform one-touch opera-
tion by assigning a setting item on MENU2 to this
switch.
࡮For the setting item, refer to 4-4. Description of
MENU 2 Functions.
Ԣ
F2 switch
࡮It becomes possible to perform one-touch opera-
tion by assigning a setting item on MENU2 to this
switch.
࡮For the setting item, refer to “4-4. Description of
MENU 2 Functions”.
ԣ
ASPECT switch
࡮This switch is pressed to change the image aspect
ratio (4:3/16:9/ZOOM). HDTV signal is only 16:9
aspect.
࡮Whether to store setting for each channel or to
make setting for all the channels together is cho-
sen on MENU2.
* ZOOMmagnifies the image area in the 4:3
letterbox.
㩷
㩷
㩷
㩷
* SDTV format signals (480i/575i) only are effec-
tive.
Ԥ
SCAN switch
࡮Press this switch to change image display sizes
(normal-scan/under-scan).
<16:9 Normal-scan> <16:9 Under-scan>
<4:3 Normal-scan> <4:3 Under-scan>
ԥ
MONO
switch
࡮This switch is pressed to make a color signal
monochrome.
* When analog component RGB is input, this func-
tion is ineffective.
Ԧ
MARK switch
࡮This switch is pressed to turn ON/OFF the
marker display.
࡮The type of marker to be displayed is set on
MENU7.
* When the internal test signal is displayed, this
function is ineffective.
㩷
ԧ
CHROMA manual control
࡮This control serves as a manual/preset switch for
chroma or a manual data variable control.
࡮The control pops out when it is pressed and the
mode is changed to MANUAL.
Ԩ
BRIGHT manual control
࡮This control serves as a manual/preset switch for
brightness or a manual data variable control.
࡮The control pops out when it is pressed and the
mode is changed to MANUAL.
ԩ
CONT manual control
࡮This control serves as a manual/preset switch for
contrast or a manual data variable control.
࡮The control pops out when it is pressed and the
mode is changed to MANUAL.
࡮This control can be an allocation to BACKLIGHT
according to the NENU setting.
Ԫ
AUDIO control
࡮Use this control to adjust the sound volume of the
front speaker or the headphones.
* An audio (analog / embedded audio / downmix
audio) to be outputted to the speaker must be set
on MENU6.
ԫ
USB terminal
࡮Connect a USB memory, and the monitor’s data
can be saved on the USB memory or the data on
the USB memory can be downloaded on another
monitor.
࡮Connect a USB mouse, and the user markers can
be drawn.
ZOOM

- 6 -
21 Stereo headphones output (stereo mini-jack type)
࡮Analog audio signals, embedded audio signals and
downmix audio signals are fed out of this termi-
nal.
࡮The analog and embedded inputs can be selected
on MENU6.
࡮Very low sound may be audible even when the
volume is at minimum position.
22 Front speakers
࡮Analog audio signals, embedded audio signals
(downmix, ch1/2, ch3/4, ch5/6 and ch7/8), and
downmix audio signals are fed out of this termi-
nal.
࡮The audio selected in the analog audio inputs,
embedded audio inputs and downmix audio in-
puts is output here.
࡮With the headphones being connected, no sound is
heard from the speakers.

- 7 -
2-2
㧚
Rear panel (left)


㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
Ԙ
AC power supply input connector
࡮The accompanying AC cable is connected to this
connector to supply AC power.
ԙ
Locking hardware
࡮This hardware is used to lock the AC plug to
prevent it from coming off.
Ԛ
DC input connector
࡮Insert the provided DC cable here to supply DC
+12V power.
࡮Insert the provided BB-904A (option) of DC cable
here to supply battery power.
ԛ
BB-904V (option)
࡮Insert the provided IDX battery here to supply
battery power.
Ԝ
BB-904A (option)
࡮Insert the provided ANTON BAUER battery (DI-
ONIC 90) here to supply battery power.
ԝ
Handle
࡮When this monitor is carried, this is improved.
࡮The knob can be drawn out at once by picking up
and lifting both ends.
BB-904V (option)
BB-904A (option)
㽵
㽶
㽷㩷
㽷㩷
㽳㩷
㪛㪚㩷㪠㪥㩷㪈㪉㪭
㪋
㪊
㪉㪈
㪈
㪉
㪊
㪋
㪞㪥㪛
㪥㪚
㪥㪚
㪈㪉㪭㩷
㪘㪚㩷㪠㪥
㪈㪇㪇㪄㪈㪉㪇㪭
㪉㪇㪇㪄㪉㪋㪇㪭
㽴㩷
㽲㩷

- 8 -
2-3
㧚
Rear panel (video inputs/outputs)
 
Ԙ
SDI A/B signal input
࡮3G-SDI, HD-SDI or SD-SDI (4:2:2) signals are
input through this connector.
࡮The format of an input signal is automatically
detected to control the monitor.
ԙ
SDI signal output
࡮The signal of the channel selected on the moni-
tor is output from the A/B channel of the input
SDI signal.
* When channels are set to ONin SDI CH
LOCKon MENU2, signal is output from only
the channel set to ON.
Ԛ
NTSC/PAL analog composite input
࡮NTSC/PAL VBS (analog composite) signals are
input through this connector.
࡮When loop-through-connections are not made, a
75΃termination should be connected.
ԛ
Analog audio input
࡮Feed analog audio signals here.
Ԝ
Analog audio output
࡮Select analog audio or downmix audio or one
pair of channels out of four paired channels
(eight embedded audio channels multiplexed in
SDI) in the MENU6. The selected 2-channel
analog audio signal is outputted from this con-
nector.
ԝ
PARALLEL REMOTE signal input
࡮Connect the accompanying remote connector here.
࡮For details of pin connections, refer to "D
Data 3:
Parallel Remote Pin Function
" or "4
4-11. Description
of MENU 8 Functions
".
࡮Make sure the cable used is shielded.
Ԟ
SERIAL REMOTE signal input
࡮Connect the BNC cable from the SRC-301A/Z(*)
serial remote controller here.
*SRC-301A/Z is discontinuation.
࡮By adopting the loop through connection, up to 99
monitors can be controlled individually or collec-
tively.
࡮Without the loop through connection in place, con-
nect a terminating plug.
࡮Set the monitor ID number on the MENU2 screen.
ԟ
RS-485 input/output
࡮This I/O is connected when performing a material
display by using the TSL UMD protocol or a TALLY
display.
࡮Up to 32 units can be loop-through-connected.
࡮Without loop-through connection, use the optional
terminating device.
* Make sure the cable used is shielded.
Ԡ
TEST terminal for factory adjustment
࡮The TEST terminal is factory adjustment. Connect
nothing to this terminal.
㽹
㪠㪥
㪩㪪㪄㪋㪏㪌
㪦㪬㪫
㪫㪜㪪㪫
㪩㪜㪤㪦㪫㪜
㪧㪘㪩㪘㪣㪣㪜㪣
㪘㪬㪛㪠㪦
㪠㪥 㪤㪦㪥㪠㪫㪦㪩㩷㪦㪬㪫
㪭㪙㪪
㪪㪜㪩㪠㪘㪣
㪩㪜㪤㪦㪫㪜
㪤㪦㪥㪠㪫㪦㪩
㪦㪬㪫
㪚㪟㩷㪙
㪚㪟㩷㪘
㪟㪛㪆㪪㪛
㪪㪛㪠
㽴㩷 㽸
㽷㩷
㽵㩷
㽺
㽶
㽲
㽳㩷

- -
9
3
㧚
Markers
㩷
3-1
㧚
Types of Markers
࡮
The displayed markers are set on MENU7.
(1) Safety marker
Active screen area
100% area
(6) Aspect marker + Safety marker
Active screen area
Aspect marker [4:3/13:9/14:9/15:9]
Active screen area
(3) 10-division
crosshatch
Active screen area
(4) Cross marker
Active screen area
(5) Aspect marker
Active screen area
Aspect marker
[4:3/13:9/14:9/15:9]
Safety marker in area,
variable from 80% to 99% (1% increments)
(7) 1.85:1 Aspect marker
Active screen area
1.85:1 Aspect marker
(8) 2.35:1 Aspect marker
Active screen area
2.35:1 Aspect marker
(9) Safety marker
Active screen area (4:3)
Variable from 80% to 99%
(1% increments)
100% area
Active screen area
Active screen area
Active screen area
Active screen area
In the 16:9 aspect ratio display mode (HDTV/SDTV)
Aspect marker
[13:9/14:9/15:9/16:9]
(10) 5-division
crosshatch
(11) 10-division
crosshatch
(12) Cross marker
(13) Aspect marker
In the 4:3 aspect ratio display mode (SDTV)
Variable from 80% to 99%
(1% increments)
(2) 5-division
crosshatch

- -
10
4
㧚
MENU Functions
㩷
4-1
㧚
List of MENU
All functions can be executed in the MENU screen.
MENU MENU1
(FORMAT)
MENU2
(MODE)
10.FORMAT DISPLAY
2.㸢Y/C SEP.
1.FUNCTION1 MODE
4.CHANGE ASPECT
6.TALLY
1.SDI VITC
3.REMOTE NO.
1.VBS FORMAT
3.㸢NTSC SETUP LVL
9.SDI CH LOCK
MENU3
(VITC/WFM/VSC)
7.REAL SCAN
2.㸢DIMMER
3.㸢SIZE
4.WFM DISPLAY
5.㸢DIMMER
6.㸢SIZE
7.㸢POSITION
8.㸢COLOR
MENU4
(SCREEN CAPTURE) 1.SCR CAPTURE
2.㸢AREA
2.FUNCTION2 MODE
9.VECTOR SCOPE
10.㸢DIMMER
11.㸢MAGNIFICATION
12.㸢SCALE
13.㸢POSITION
14.㸢COLOR
11.BATTERY TYPE
8.ψPOSITION
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪻㪼㪺㫆㪻㪼㫉㩷㪰㪆㪚㩷㫊㪼㫇㪸㫉㪸㫋㫀㫆㫅
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪥㪫㪪㪚㩷㫊㪼㫋㫌㫇㩷㫃㪼㫍㪼㫃
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪭㪙㪪㩷㫀㫅㫇㫌㫋
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪽㫌㫅㪺㫋㫀㫆㫅㩷㪸㫊㫊㫀㪾㫅㫄㪼㫅㫋㩷㫆㪽㩷㪝㪈㩿㪝㫌㫅㪺㫋㫀㫆㫅㩷㪈㪀㫊㫎㫀㫋㪺㪿
Setting the automatic/manual aspect ratio change as per
reception channel
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㫋㪸㫃㫃㫐㩷㫃㪸㫄㫇㩷㪻㫀㫊㫇㫃㪸㫐㩷㪽㫆㫉㫄㪸㫋
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㫄㫆㫅㫀㫋㫆㫉㩷㪠㪛㩷㪺㫆㪻㪼㩷㪽㫆㫉㩷㫉㪼㫄㫆㫋㪼㩷㪺㫆㫅㫋㫉㫆㫃
Setting the SDI channel lock ON/OFF
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㫊㪸㫄㪼㪄㫊㫀㫑㪼㩷㩿㪻㫆㫋㪄㪹㫐㪄㪻㫆㫋㪀㩷㪻㫀㫊㫇㫃㪸㫐㩷㪦㪥㪆㪦㪝㪝
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪽㫌㫅㪺㫋㫀㫆㫅㩷㪸㫊㫊㫀㪾㫅㫄㪼㫅㫋㩷㫆㪽㩷㪝㪉㩿㪝㫌㫅㪺㫋㫀㫆㫅㩷㪉㪀㫊㫎㫀㫋㪺㪿
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪪㪛㪠㩷㪜㪩㪩㪦㪩㩷㪣㪜㪛㩷㪻㫀㫊㫇㫃㪸㫐㩷㪦㪥㪆㪦㪝㪝
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪽㫆㫉㫄㪸㫋㩷㪻㫀㫊㫇㫃㪸㫐㩷㪦㪥㪆㪦㪝㪝㪆㪫㪠㪤㪜㪩㩷㪸㫋㩷㫊㫀㪾㫅㪸㫃㩷㫊㫎㫀㫋㪺㪿㫀㫅㪾
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㫋㫐㫇㪼㩷㫆㪽㩷㪹㪸㫋㫋㪼㫉㫐
Setting the SDI VITC display ON/OFF
Setting the SDI VITC display brightness
Setting the waveform display ON/OFF
Setting the SDI VITC display size
Setting the waveform display brightness
Setting the waveform display size
Setting the waveform display position (right/center/left)
Setting the waveform display color (white/green)
Setting the VECTOR SCOPE display ON/OFF
Setting the VECTOR SCOPE display brightness
Setting the VECTOR SCOPE display magnification ratio
Setting the COLOR BOX scale display (75%/100%)
Setting the VECTOR SCOPE display position (right/center/left)
Setting the VECTOR SCOPE display color (white/green)
Executing the 2-picture split mode
Setting the 2-picture split mode display area
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪺㪿㫉㫆㫄㪸㩷㪾㪸㫀㫅㩷㪄㫌㫇㩷㪦㪥㪆㪦㪝㪝㩷
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪠㪧㩷㪺㫆㫅㫍㪼㫉㫊㫀㫆㫅㩷㫄㫆㪻㪼㩷㩿㪝㪠㪜㪣㪛㪆㪝㪩㪘㪤㪜㪀
㪘㪻㫁㫌㫊㫋㫀㫅㪾㩷㫋㪿㪼㩷㪿㫆㫉㫀㫑㫆㫅㫋㪸㫃㩷㫊㪺㫉㪼㪼㫅㩷㫇㫆㫊㫀㫋㫀㫆㫅
㪘㪻㫁㫌㫊㫋㫀㫅㪾㩷㫋㪿㪼㩷㫍㪼㫉㫋㫀㪺㪸㫃㩷㫊㪺㫉㪼㪼㫅㩷㫇㫆㫊㫀㫋㫀㫆㫅
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪺㫆㫅㫋㫉㪸㫊㫋㩷㫉㪸㫅㪾㪼㩷㩿㪥㫆㫉㫄㪸㫃㪆㪮㫀㪻㪼㪀
5.CONT VR ASSIGN 㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪸㫊㫊㫀㪾㫅㫄㪼㫅㫋㩷㫆㪽㩷㵰㪚㪦㪥㪫㵱㩷㫄㪸㫅㫌㪸㫃㩷㪺㫆㫅㫋㫉㫆㫃㩷㩷
MENU5
(VIDEO) 1.CHROMA GAIN UP
2.IP MODE
3.H 䌐㪦㪪㪠㪫㪠㪦㪥
4.V POSITION
5.CONTRAST RANGE
3.FUL CAPTURE
4.CHG MANUAL
5.CHG AUTO
6.㸢INTERVAL
7.USB FILE NO.
8.WRIGHT TO MEM
9.DOWNLOAD
Executing the full capture mode
Manual switching mode between full capture image and input
signal image
Setting up the interval of the automatic switching mode
㪪㪼㫋㫋㫀㫅㪾㩷㫋㪿㪼㩷㪽㫀㫃㪼㩷㫅㫌㫄㪹㪼㫉㩷㫆㪽㩷㫋㪿㪼㩷㪽㫌㫃㫃㩷㪺㪸㫇㫋㫌㫉㪼㩷㫀㫄㪸㪾㪼
Writing the full capture image onto the USB memory
㪛㫆㫎㫅㫃㫆㪸㪻㫀㫅㪾㩷㪽㫉㫆㫄㩷㪬㪪㪙㩷㫄㪼㫄㫆㫉㫐㩷㫋㫆㩷㫄㫆㫅㫀㫋㫆㫉
Automatic switching mode between full capture image and
input signal image