Ikegami HTM-1505R CS User manual

MODELHTM-1 SOSR
~ ..... MODEL HTIVl-1505CS .
··..MULTl-FORIVIATCOLOR MONITOR
. .
OPERATIONMAN·UAL
lkegarni

1':
Safety Precautions
For safe and correct usage
Thoroughly readthe "Safety Precautions" andtheoperationmanual
beforeusingtheunit.
Keepthem carefully after reading and useasreadyreference.
Pictorial Symbols
The "Safety Precautions" and markings on the product contain various
pictorial symbols to assurethe safety useof the product andprevent an
injury to you andother personsaswell asproperty damage.
As each symbol has the following meanings, thoroughly understand
them before usingthe unit.
Please note that some precautions may not be applicable to the
product that you purchased.
Indicates a potentially hazardous situation
t WARNING: that may arise due to improper handling by
ill taking no notice of this symbol and could
result in a serious iniurv or death.
Indicates a potentially hazardous situation
t CAUTION: that may arise due to improper handling by
ill taking no notice of this symbol and could
result in an injurv or property damage only.
[Note] 6,. meansa heads-up.
Examoles of symbols
Symbol"(!}' means a prohibited·action.
The content of prohibited matter is mentioned near or in
the figure. (The figure on the left side represents"Caution
· fordisassemblina".
Symbol "l::i;" means a mandatory or directive content.
Practicalprecautions are shown in the figure. (The figure
on the left side represents"Pull out power plug from plug
outlet.")
LhCAUTION
When using the unit·
0 Do not place a receptacle containing water or a small
metallic piece on the unit!
If water spills in the unit, a fire or electric shock may be
caused.
0 Do not use other power supply voltage than specified I
A fire or electric shock may be caused.
0 Do not put a metal body or flammable material into
the opening of the unit!
Do not drop in such material! A fire or electric shock
mav be caused.
@ Do not make alterations to the unit!
A fire or electric shock may be caused.
When installinQ the unit:
0 Do not set the unit in an unstable place!
Itmay drop orturn down, causingan injury.
0 Do not connect to any other equipment than specified!
A fire or electricshockmay be caused.
When fixing the unit, ask a professional contractor!.
When fixing the unit, do so in accordance with the
ill specified procedure; otherwise it· may drop or turn
down, causing a fire, electric shock or injury.
Especially when fixing it to the wall or ceiling, be sure
to ask a professional contractor.
When an abnormal state occurs·
If the unit produces smoke, gives out a foul smell or
ill produces an abnormal sound, turn off the power
switch immediately and pull out the power plug!
~
If the unit is used as it is, a fire or electric shock may
be caused. Check that no smoke is produced, and
then contact the dealer or sales representative.
ill If water or foreign matter enters the.unit, turn off the
power switch and pull out the power plug!
~
If the unit is used as it is, a fire or electric shock may
be caused. Check that no smoke is produced, and
then contact the dealer or sales representative.
ill If the unit is dropped or the case is broken, turn off
the power switch and pull out the power plug!
~
If the unit is used as it is, a fire or electric shock may
be caused. Contact the dealer or sales representative.
ill If the unit fails to operate properly, tum off the power
switch and pull out the power plug!
~ If the unit is used--asitis; a fire or electric shock may
be caused. Contact the dealer or sales representative.
Do not use any damaged power cord (exposed core,
ill broken wire, etc.)!
If the unit is used as it is, a fire or electric shock may
be caused. Contact the dealer or sales representative.

ill WARNING:
When installing the unit:
(S) Do not place a heavy thing on the unit!
The unit may losea balanceor drop, causingan injury.
(S) Do not get a leg over the unit or carrying case!
Do not sit down on it!
The unit may breakdown orturn down, causingan injury.
(S) When movingthe unit,be sureto tum off the powerswitch,
pull out the power plug and remove the connectingcable
betweenthe unitand equipmentbeforehand.
The cordmay bedamaged,causingafireorelectricshock.
@ When the unit is not used for a long period of time, be
sure to pull out the power plug for safety's sake.
Otherwise,it may cause a fire.
When installing the unit:
Do not block up the ventilating hole of the unit!
Jfthe ventilating hole of the unit is blocked up, heat
will accumylate internally, causing a fire. Avoid the
following usage:
• Turning up or down the unit. Turning it sideways.
• Pushing it in ill-ventilated place.
· Placing ii on a carpet etc.
• Covering it with a table cloth etc.
Hints on proper usage
Wh th ·t
en usma e Uni:
· When using the unit in a water-place such as bathroom,
poolside, etc., prevent water from flowing into the unit and
cable; otherwise causing an electric shock.
When using it in rainyweather, during snowing,on the seaside
or waterside, and in a cooking place, use care to prevent such
an accident.
· When snow comes on, check the surrounding conditions
before use.
Stop using the unit temporarily as necessary and do not
touch it; otherwise causing an electric shock.
• Do not connect any equipment whose required electric
power exceeds the wattage (W) that can be supplied from
the AC outlet.
Refer to wattage shown near the AC outlet or in the operation
manual.
· Do not bend (or twist or pull) the power cord and
connecting cable excessively.
The covering material of the cord and cable may break,
causing an electric shock.
When ms a ma t Ir th ·t e Uni:
Avoid installing the unit in a moist place, dusty place or any
other place exposed to oily smoke and vapor; otherwise causing
an electric shock.
Do not place the unit near a cooking table or humidifier.
• As this unit is heavy (over 10Kg), carry it by 2 or more persons.
If ii is carried by one person, it may turn down or drop, some-
times causing an physical damage to the waist or hand or a
physicalinjury.
• Take preventive measures against the overturn of the unit
due to an earthquake or sudden shock.
As the unit may overturn and cause a physical injury, take
preventive measures against the overturn.
Maintenance
Turn off the power switch and pull out the power plug before
maintenance; otherwise, causino an electric shock.
In order to keep a long and stable performance, "Periodical check"
is recommended. For details of the periodical check, consult with
the sales representative.
As the unit has high-voltage parts in it, an expert who has the
knowledge about the product should perform these check,
maintenance and repair; otherwise causino an electric shock.
OPERATING PRECAUTIONS
In order to use the monitor in safety, thoroughly read this
book and pay special attention to the following matters:
1. Do not use other power supply than specified (AD
and DC).
2. Do not give an excessive shock to the monitor.
Otherwise, a trouble may occur, also causing a danger
due to the implosion of CRT.
3. Do not use and keep the monitor in the following
places:
A place with operating temperature outside the
prescribed range
Pay specialattentionto radiationof heat,becausethe inside of
themonitormaybeheatedbydirectsunlightevenif itisusedout
ofdoorsattheprescribedsurroundingtemperature.
Also, never block off both exhaustopeningon the back of the
monitorandairinletonthebottom. . . . .
Especially,checkthatany blackoutcurtaindoes not blockoffthe
exhaustopening.
A rainy,snowy and/or humid place
Itmaycausean electricleakanda trouble.
A placewhere strong magnetism is generated.
The picture may be distorted in the neighborhood of the
transmittingstationof a TV stationandsomethingthatgenerates
high-intensityradiowaves.
In this case,a normalpicturecan be obtainedby changingthe
positionofthemonitoraccordingtocircumstances.
Furthermore,inorderto protectthemonitorfroma strongelectric
field, it may be necessary to provide an external shield
separately.
4. Avoid the direct sunlight to CRT.
ExposingCRTto thedirectsunlightfora longperiodoftime may ···-·
deterioratethefluorescentscreenofCRT.
So,keepthisfactinmindwhenusingthemonitoroutofdoors.
5. Avoid displaying a fixed bright image for long time.
Keep in mind that displayinga fixed blight image for long time
mayresultintheburningofCRT.
Warranty
Anydefectthatoccursduringnormalusewithinoneyearafterthe
dateofdeliveryshallberepairedfreeofcharge.
However,CRTandfusesshallnotbewarranted.
Ifa picturedoes notappearaftercompletionof dailyadjustment
or it seemsthat the monitorfails,pleasecontactthe storefrom
whichyouboughtthemonitororTECHNOIKEGAMI.
Accessories
As the monitorcomeswith the followingaccessories,checkfor
missing:
1. OperationManual
2. PowerCable
3. RemoteConnector

HTM-1505R/HTM-1505CS
MODELHTM-1505R
MODELHTM-1505CS
MULTI FORMAT COLOR MONITOR
SAFETY PRECAUTIONS
OPERATING PRECAUTIONS
1. General Description ........................................ .
1.1 General Description ..................................... .
1.2 Features ........................................................ .
2. Specifications .............................. ..................... 3
2.1 Cqmmon Specifications ................................ 3
(I) General ............................................................... 3
(2) Video Signal System ............................................ 3
(3) Brightness/Contrast ............................................ 3
(4) Deflection/Synchronous System ........................ 3
(5) Functions ................................................... :........ 3
(6) Memory .............................................................. 4
(7) Applicable Standard ........................................... 4
2.2 Individual Specifications................................ 4
(I) YPbPr/RGB input module .................................. 4
(2) Multi SDI input module ..................................... 5
(3) SD-SDI input module ......................................... 5
(4) Decoder input module ........................................ 6
2.3 Options ................ ............................ ............... 6
2.4 External View .......................................... ....... 7
(I) HTM-1505R ................................................ 7
(2) HTM-1505CS .............................................. 9
3. Installations ...........................................................11
3.1 Connection to external equipment ............... II
(I) Standard module ............................................... 11
(2) Multi SDI input module ................................... 12
(3) SD-SDI input module ....................................... 13
(4) Decoder input module ...................................... 13
(5) Dual component input module ......................... 14
3.2 Connection of parallel remote connector .... 15
(I) Pin function .......... ............................................ 15
(2) Connectors used ............................................... 15
CONTENTS
4. Daily Adjustment ......................................................... 16
HTM-1550R model
4.1 Power supply ........................................................ 16
4.2 Name and function of Front Left Panel................ 16
4.3 Name and function of Control section ............... 17
(I) Front panel .................................................................... 17
(2) Drawer panel ................................................................. 20
4.4 Entry and Change of Data .............. ..................... 23
(I) Entry and Change of preset data .................................. 23
(2) Entry and Change of file data ...................................... 24
HTM-1505CS model
4.5 Power supply ............................................ ............ 25
4.6 Name and function of Front Left Panel .............. 25
4.7 Operation for Wireless Remote Controller ......... 26
(I} Cautions for using remote controller ........................... 26
{2) Initialization ofremote control operation .................... 26
(3) Name and function of operating key board ................. 28
4.8 Entry and Change of Data ................................... 32
(I) Entry and Change of preset data .................................. 32
(2) Changing the screen size ............................................. 33
Common to HTM-1505R/HTM-1505CS
4.9 Kinds of Markers ..........................................................34
4.10How to adjust ..............................................................35
(I) Brightness adjustment ................................................. 35
(2) Contrast adjustmen( ..................................................... 35
(3) White balance adjustment ........................................... 35
(4) Color balance adjustment ............................................ 36
(5) Focus adjustment ......................................................... 37
(6) Rotation adjustment .................................................... 37
(7) Screen center adjustment ............................................. 38
(8) Screen distortion adjustment ....................................... 39
(9) Screen size adjustment ................................................ 39
4.11Menu Facility ........................................................ 41
(I) List of menus ............................................................... 41
(2) Flow of menu-driven operations ................................. 42
(3) Functional description of menu I ................................ 44
(4) Functional description of menu 2 ................................ 44
(5) Functional description of menu 3 ................................ 45
(6) Functional description of menu 4 ................................ 45
(7) Functional description of menu 5 ................................ 45
(8) Functional description of menu 6 ................................ 46
(9) Functional description of menu 7 .................................. 46
4.12Explanation of messages display on screen ..... 47
5. How to mount optional equipment ........................ 48
5.1 Option module ...................................................... 48
(I) HTM-1550R ........................................................ 48
(2) HTM-1550CS ..................................................... 49
5.2 Mounting on a rack .............................................. 50
(I) RS-1550S ............................................................. 50
(2) RS-1550CS .......................................................... 51
5.3 Remote controller ................................................ 52
(I) RS-1550S ......................... .................................. 52
(2) RS-1550CS ........................................................ 53
6. User's memorandum ............................................... 54

HTM-1505R/HTM-1505CS
___-----~-----.H:rM...1.5.0.5Rttf+M-1-505CS -------------
MULTI-FORMAT COLOR MONITOR
1.1GeneralDescription
Thismonitorisa 15-inchmulti-fonnatcolormonitordesignedto
meeteachfonnatof HDTVand foruse withSDTY,and it canalso
beeflectivelyusedinvariousspaces,suchas editingand monitoring
racksandsendingcontroldeskina sub-controlroom,broadcastvan,
etc.
Inorderto meetvariousbroadcastingfonnatsandsystemneeds,
thismonitorcOITespondsto I080i, I035i,and 720p forHDTV,and
480pandNTSC,PAL-Bandmulti-TVfo1matforSDTV(including
options).
Moreove1;this mo_nitoris easilycompatiblewith HD/SD serial
digitalinputsas well as usual analogcomponentsand composite
inputs.
Inviewofsystemexpandabilityandeaseofmaintenance,a lotof
optionalplug-in modulesare supplied,so system change can be
easilyaccomplishedonlyby insertinga modulewithoutopeningthe
bodycover.
In addition to a newly developed SDI module for multi-
fonnatted inputs, another new type module correspondingto
embeddedaudioisavailable.
Variousfi111ctionssuch as analog or AES/EBUdigitaloutput,
audiolevelmeter,etc. are equippedin the embeddedaudio,so that
bothpictureandaudiocanb_esimultaneouslymonitoredonlybyone
unit,demonstratingahighperfo1mance-to-costratio.
1.2Features
(1) Correspondsto multi-format
InputsignalscmTespondtothefollowingbroadcastformats:
• 525i(NTSC): ITU-60I
• 625i(PAL-B): ITU-601
l035i/60,59.94: SMPTE240M,BTAS-00IB
IOS0i/60,59.94: SMPTE274M
l080i/50: SMPTE274M [Option]
l080i/48,47.95: SMPTERP211[Option]
• 720p/60,59.94: SMPTE296M
• 480P/60,59.94: SMPTE293M
(2) Correspondstomulti-formatSDI
Multi-fommtcompatibleSDI module(DKM-5018)is capableof
receivingHD-SDIsignalsor SD-SDI(4:2:2)signalsat the same
inputte1minalwithoutdiscrimination.
Monitor automaticallydiscriminatesthe entered HD-SDI·or
SD-SDI(4:2:2)signals,anddisplaysinaproperfonnat.
(3) Embeddedaudiooutputcompatible
Anoptionalmulti-fonnatSDI(AV,AYOtype)modulecompatible
with embeddedaudio output is providedwith a demultiplexer
circuit,and can extractand outputaudio signalssupe1posedon
HD-SDIsignalsandSD-SDI(4:2:2)signals.
AnAVtypeaudiooutputof analog2-channel(outputchannelisset
on a menu)and an AYOtypeaudiooutputof AES/EBUdigital
8-channelareavailable.
(4) Embeddedaudiocompatiblelevelmeter
DAM-504,508 modules[option]are audio levei meterscom-
patiblewithembeddedaudio,and monitors4 or 8 channelaudio
signals supe1posedon SDI signals, together with picture
simultaneously.
The level meter is of an LED type installedin the escutcheon,
assuringvisibilityandeaseofmonitoring.
It is also united with the monito1;eliminatingthe need for
exclusivespace.
(5) Remotecontrolfunction
Three types of remote controllers(parallel/infrared/serial)are
availableaccordingtotheinstallationplaceandoperatingpwposes.
Inadditiontotheusualparalleltype,a serialinputinterfacethatcan
be remotelyoperatedwith one BNC coaxialcable is standard
equipment.
A single serialremote controller_SRC-301A [option]makes it
possibleto remotelyoperateupto 99 monitorsindividuallyonly
by makinga loop-throughconnectionamongvarious monitors
(17,18,20,30,80,90,HTMseriesmonitor,etc.)
Moreover, an infrared wireless remote control RCT-201A
[option]isalsoavailable.
(6) Digitalcontrol
Each digitaldata is processedat IO bits, and data changeand
settingcanbeeasilyperfonnedwith.arotaryencoder.
Imagefield,screenposition,side pin and trapezoidal-distortion
correctioncan also be remotelyoperatedto meet varioussignal
fonnatsflexibly.
(7) Fourkindsofcolortemperaturecanbe
storedinmemory
Inadditionto thefactorydefaultcolor-temperatureD93/065,one
kindoforiginalcolortemperaturecanbestoredinmemory.
This makesit easierto set and selectthe optimumwhitebalance
quicklyaccordingto the stateof inputimageand the purposeof
use.
(8) BFS(BeamFeedbackSystem)
A BFScircuitthatdetectsthecathodecurrentofCRTisemployed
sothata stablewhitebalancecanbeobtainedfora longperiodof
timeeveniftheemissionofCRTchanges.
(9) 3-Iinecombfilter(NTSC)incorporated
It isa decodermoduleincorporatinga 3-linecombfilterrealizing
thewidebandofvideoby a digitaldelaydrivesystemwitha 8fsc
clockatthetimeofNTSC analogcompositesignalinput.
YICseparationreproduceshigh-resolutionpictureswithminimiz.ed
crosscolorandcrossluminancebyadoptinga3-linecombfilterof
Faroudja(IM)system.
*AnoptionalNTSCdecodermoduleDE-801isrequired.

2
HTM-1505R/HTM-1505CS L
(10)A lotoftestsignalsincorpo.rated
A lotof testsignalsconvenientforaqjustmentof monitor-Cross
hatch, Flat field (50%), Window (100%), Character, and
Stepped waves withpluge signaletc.- areincorporated.
Moreover,l080i, 1035iand720pcanbeselectedatHDTVmode,
andtestsignalsofeachfonnatof525,625canbeselectedatSDTV
modeona menu.
(11)Variousmarkersincorporated
Displayof4:3markersispossibleat 16:9displaymode.
Inaddition,80%,88%,90%,93%, I00%andmanyothermarkers
aredisplayedfortherespective4:3/16:9aspectsatNTSCmode.
(12)Shadowfunction
As the functionof displayingan imageareaof 4:3 at the timeof
16:9 aspect picture and shadowingother picture portion (the
contrastofshadowportioncanbesetto0%or40%)isincorporated,
it is possible to display an picture of 4:3 immediatelywhile
monitoringanpictureof 16:9.
Shadow ON/OFF can be remotely operated, so that quick
switchingispossible.
(13)Degausstimer
It is possibleto set the operationof auto degaussdesignedto
automaticallyoperateabout4 secondsaftertumingon themonitor
to the intendedtime (0to 4.5 secondsat intervalsof 0.5 second)
withatimer.
This minimizesa nish cu!l'entthat flows when turning on the
systemusingmru1ymonitorsatthesrunetime.
(14)Designandstructure
foreasymaintenanceandexpandability
Signalconditioningmoduleisof a plug-intype(includingoptional
modules)that is easily detachablefrom the reru·side without
removingthecoverforeaseofmaintenance.
In additionto the DKM-501B multi-SDImodule(standru·dequip-
ment)ru1danalogcomponentsignal(YPbPr),it ispossibleto add
anoptionalmoduletoexpandthefunction.
HTM-1505R: 3 slots
· HTM-1505CS: 2 slots
·. J I i Ill ·11•n::rm 1] ER
(15)High-perfonnanceinfinegun CRT
A high-perfonnanceinline-guntypeCRT with 0.27mmdot mask
pitch is employed to assure high definitionand minimize the
reflectionofoutdoordaylightetc.
Fwthennore,doming(shiftof beamduetothe1maldeformation)of
the shadowmask of CRT,which will occur when brightnessis
increased,hasbeengreatlyimproved.
(16)Contrastcorrectionforeachscreensize
In orderto preventa brightnesschangethat will occurwhen the
currentdensityof the electrongun increasesdue to the contraction
of the imagefieldlikea normal/underscreenor screensof 4:3 and
16:9.contrastconectioniscruTiedoutsothatbrightnessmayalways
beconstantineachscreensize.
(17)HD4:3scanning
A functionof enlargingthe 4:3 area picture alone to the whole
picturefrrune(aspectratio4:3)at thetimeof HDTV isprovidedto
monitorthepictureinrealtimewhendown-convertingtothe4:3of
SDTVforHDTVrecording.
(18)High-perfonnance
high-voltage regulation circuit
As a regulationcircuitthatcontrolspulsesperscanninglineisused
in the high-voltagecircuit,assuringquick response,minimizing
screendistortionandrealizingverystablepicture.
(19)Autoset-upfunction
Whenan autoset-upprobeASP-80 [option]is used,the factory
defaultcolortemperaturecanbeautomaticallycontrolled.
Fu1thermore,whenoperator'soriginalcolortemperatureissetonthe
monitrn;twoormoremonitorscanalsobecontrolledautomatically
tothesrunecolortemperature.
(20)Improvedspacefactor!HTM-1505CSmodelj
ThefrontsideofHTM-1505CSmodelhasbeenmadesmallabout
20%byremovingthecontrolpanelfromHTM-1505Rmodel.
When installingon a controltable or monitorrack, space factor
improves,contributinglargelytothesystemdesign.

2.1 Common specifications
(1)General
1. Power supply ACsinglephase,50/601--Iz
Withinrangeof!00V line: I00V~I20V±l0%
Withinrangeof200V line:200V~240V±IO%
2. Power Consumption
HTM-1505R: Approx.240W
HTM-1505CS: Approx.220W
3. AmbientTemperature 0°C ~ +40"C
4. Humidity 90%orless(Nocondensationshalloccur)
5. Dimensions and Weight
HTM-1SOSR: 450cwJx3I0a-rJx5I5(DJl11l11Approx.28kg
HTM-1SOSCS: 350(W)x300(1-Qx525coimrnApprox.25kg
6. Standard Accessory Powercable,Remoteconnector,
Operationmanual ···Oneseteach
7. Duty
8. X-rayRadiation
Continuous111nningduty
Below0.1mR/1-1
(Inallplacesatadistanceofmorethan
50mmfromtheoutsideofmonitor)
(2)VideoSignalSystem
1. Frequency Characteristics (AtYPbPrinputmode)
a)HDTV: 60Hz~25Ml-lz: +ldB/-3dB
Above25MHz: Desendingresponce
b)SDTV: 60Hz~ IOMI-lz:+1dB/-3dB
AboveI0MHz: Desendingresponce
2.Sag Lessthan5%
3. Blacktevel Stability
LessthanI% incaseof 10%to90%changeofAPL
4. Aperture Correctionamount
Acjjustablebymorethan+6c!Battl1efollowingfrequency:
a) HDTV: IOMl-lz±2.5Ml-lz
b)SDTV: 4Ml-lz··· *
* ForSDTV,optionaldecodermodule(NTSC:DE-801,PAL:DE-802)
ismounted. Co1Tespondstoanalog/digitalcompositesignalalone.
5. Noise Synchronousnoies: Above-46dB
Humnoise: Above-50dB
Others: Above-50dB
(3)Brightness/Contrast
1. CRT Dottriopitch:0.27111111
2. HorizontalResolution
Morethan750lineswhenitis 120cd/m
2 atthecenterof
screenincaseofYPbPrinput(AtHDTVmode).
3. Preset Contrast
Above120cd/m2 (Factorydefault)
4. MaximumBrightness Above240cd/m2
(100%windowsignal,BrightnessPRESET,ContrastMAX)
HTM-1505R/HTM-1505CS
(4)Deflection/SynchronousSystem
1. 16 :9 display size
a) NORMAL: 16:9sizet,mgentto effectiveframeofCRT
b) UNDER: 270cwixI52crQrnm
2. Deflection
a) SDTV
NORMALSCAN:(4:3/16: 9)
UNDERSCAN: (4: 3/16: 9)
b) HDTV
NORMALSCAN:(16:9)
UNDER.SCAN: (16:9)
HD4:3 SCAN: (Zoomingti.mctionof4:3 area)
3.Deflectiondistortion Within ±1% ofscreenheight
(Deflectionlinearityandrasterdistortion)
4. Stabilityof Synchronization
Inputsignaloperatesstablyinthefollowingrange:
Internalsynchronization:±6dBofratedvalueofpictureinputlevel
Externalsynchronization:Externalsyncinputlevel 0.3to8Vp-p
5. Highvoltage
Generatedvoltag: 25kV±lkV
Highvoltagefluctuation: Lessthan3%basedon I00pA
withinrangeofbeamcu1Tent0
to600pA.
6. Convergence
Within90% range ofscreenheight: Lessthan0.4mm
Within 90% range ofscreenwidth: Lessthan0.5mm
(5)Fanctions
1. Markerfunction
a) Center marker: ON/OFFcanbesetonthemenu.
b) Safetitle: Indicatesthe followingmarkersaccordingto
aspectualstatus(4:3/16:9).
( )indicatestl1easpectwhenmarkersaredisplayed.
• 80% + 100%
· 88% + 100%
· 90% + 100%
· 93% + 100%
• 5 devidedcrosshatch
· IOdevidedcrosshatch
• Cross
• 14:9 IO0¾area
· 13: 9 I00¾area
· 4: 3 marker
· 4: 3 marker+ 80%(4: 3)
2. Shadow function
(4:3/16:9)
(4:3/16:9)
(4:3/16:9)
(4:3/16:9)
(4:3/16:9)
(4:3/16:9)
(4:3/16:9)
(16: 9)
(16: 9)
(16: 9)
marker(l6: 9)
Functionorapplyingthefollowingshadowof4:3in 16:9mode
· 4:3marker+Shadow
· 4:3marker+80%(4:3)Marker+shadow
· Shadowonly
3

l
4
HTM-1505R/HTM-1505CS
3. Autosetup
Whenan autoset-upprobeASP-80[option]is used,automatic
ac(justmentofwhitebalanceispossible.
4. Remote control
a) Parallelremotecontrolchannel
COMPOSITE'lAUX/HD-SDI/SD-SDI, RGBNPbP1:
COLOR/MONO, SYNCINT/EXT, 4: 3/16:9,
4: 3MARKERON/OFF, 4: 3SHADOWON/OFF,
TALLYON/OFF
b) Serialreritotecontrol
Input interface·is standard equipment Almost all monitor
functionscanbecontrolled.
SRC-301Aserialremotecontrollerisoption.
c) Infraredremotecontrol
RCT-20Ainfraredremotecontrollerisoption.
5. Built-intest signal (Changeformatonmenu.)
• Cross-hatching
• 50%flatfield
• 100%window
• Character
• Steppedwaveswithplugesignal
6. Beam feedback system (BFS)
7. Menu assist
• Settingofinputsignalfonnat
• SettfngofRGBNPbPrswitching
• Settingoftestsignalfonnat
•"ON/OFFsettingofcentercrossdisplayofmarker
• Settingofmarkercolor
• SettingofR emoteIDnunber
• Timesettingofdegausstimer
• %displayofeachpresetdata
• Passwordsetting·
• Settingofautoset-up
• Embeddedaudio-relatedsetting
(6) Memory
1. KindofMemory
ROM: 64KbyteprogrammableROM
RAM: 32KbytestaticRAM
2. BatteryBack-up
Memoryretentiontime:IOyearsormore
Battery: BR2330-lHFlithiumbattery
(7) Applicablestandards
• Safetystandard: ConformingtoUL1950
• Radionoise: FCCClass-A
• X-ray radiation: DHHS
2-2.IndividualSpecifications
* DKM-501B multi-SDI2 and YPbPr/RGB I-input module are
standardequipment
(1)YPbPr/RGBinputmodule
• YPbPr/RGBI inputmodule[standardequipment]
· DCH-501dualcomponentmodule[torYPbPiiRGBIinpL~expansion]
1.Input/Outputterminal
a) YPbPr/RGB: I inputmodule[standard]
YPbPr/RGB: BNC1-line(Loopthrough)
Synchronousinput: BNCI-line(Loopthrough)
b) DCH-501
YPbPr/RGB: BNC1-line(Loopthrough)
2. Inputsignalformat(YpbPr/RGB)
a) SDTV
• 525i/59.94
•625i/50
b) HDTV
• 1035i/60,59.94
• 1080i/60.59.94
• 1080i/50
• 1080i/48,47.95
• 720p/59.94,60
3. Inputlevel
[Option]
[Option]
(Type-Ionly)
a) HDTV(BTAS-00IB)
• Y,G,B,RinputV: 700mVp-p
S: ±300mVp-p
• Pb,PrinputV : ±350mVp-p
• Synchronousinput:±300mVp-p
b) SDTV(SMPTE/EBUNIO)
• RGBinputVS: I.0Vp-p
V: 0.7Vp-p
Positivepolarity
Positivepolarity
Positivepolarity
Positivepolarity
Whereeachof R, G andB hassyncsignalor no syncsignal,
andwhereGalonehassyncsignal:
• YpbPrinput
YsignalWHITE(100%):700mVp-p
SETUP: 0mVp-p
SYNC: 300mVp-p
PbPrsignal: 525mVp-p
(IOO/0n5/0COLORBAR)
Syncinput: 0.3~8Vp-p Negativepolarity
4. Inputimpedance Highimpedancebridgeconnection
or750.tennination
[750.terminationplugisoption].
5. Returnloss Above46dB(I0MHz)

(2)MultiSDIinputmodule
· DKM-5018 (Multi SDImodule)[standard]
· DKM-501A(MultiSDImodule)
Equippedwithx/sinxcoITectiontype
high-performancevideosignalpostfilter
· DKM-501AAV/BAV
(Multi-SDImodulecompatiblewithembeddedanalogaudiooutput)
· DKM-501AAVD/BAVD
(Multi-SDIrnodulecornpatiblewithembeddedAES/EBUaudiooutput)
Videosystem
1.Input/Outputterminal
Input: BNC2-lines
Output: BNC I-line(Onlyoneselectedoutputisactiveloop-through.)
2. Inputsignalformat(HD/SDautorecognition)
a) HD-SDI
1035i/60,59.94
• 1080i/60,59.94
• 720p/60,59.94(Type-Ionly)
b) SD-SDI(4:2:2)
525i/59.94
• 625i/50
3. InputLevelRating
4. TransmissionSpeed
a) HD-SDI:
b) SD-SDI (4:2:2):
5. QuantifyingBitNumber
800mVp-p±10%
l.485Gb/s
270Mb/s
6. Input/Outputimpedance
10bits
750
7. Returnloss
Audiosystem
Above15d8(~742.5MHz)
AboveIOdB(742.5~1485MHz)
Commonto embeddedaudiospecifications
1. Formatcorrespondingto embeddedaudio input
SMJYfE272M:480i/59.94 (4:2:2)
576i/50 (4:2:2)
SMJYfE299M:I035i/60,59.94
1080i/60,59.94
1080i/50
1080i/48,47.95
720p/60,59.94
2.FormatChange AutomaticChange
3. SamplingFrequency 48kHz(Synchronizedwithvideolock)
HTM-1505R/HTM-1505CS
Analog Audio Output (AVtype)
*Analogaudiolevel:Od8s=-0.775V1ms
1.OutputTerminal XLR-5-32(Canon5-pin,Male)
2. Line-out Analogaudio2channels
Active(transformerless)balancetype
3. RatedOutputLevel +4dBs *Load-impedanceIOI&
(Atthetimeofdigitalaudiolevel:-20dBFS)
4. MaximumOutputLevel
+24dBs*Load-impedanceIOk.O.
(Atthetimeofdigitalaudiolevel:OdBFS)
5. Output-Impedance 500
6. MinimumLoadImpedance 6000
7. QuntuifyingBitNumber
8. Emphasis
9. FrequencyCharacteristic
10.Signal-to-NoiseRatio
11.DynamicRange
12.CrossTalk
13.TotalHarmonicDistortion
24bits/ch
50115µ sdigitalemphasis
(Automaticdiscrimination)
20~20kHz± !dB
Above80dB
Above80dB
Above60dB
(IKHzatmaximumoutput)
Above0.1%
(Atthetimeofratedoutput)
AES/EBU OutputSystem (AVDType)
*Digitalaudiolevel:OdBFSfollbit/li.11Iscale
1. OutputConnector BNC(PairChannel)4 lines
2. OutputStandard AES/EBUStandard(formonitor)
3. OutputImpedance 750
(3)SD-SDIinputmodule(Option)
· DK-801(4:2:2digitalcomponentmodule)
*NotcoITespondingtoembeddedaudio.
1.Input/OutputTerminal
BNC2lines(Activeloop-through)
* Signalsinterlockedwith achannelselectedonthemonitorside
areoutputaccordingtosettingsinthemodule.
2. InputSignalFormat
4: 2: 2digitalcomponentsignal(525i/59.94,625i/50)
3. Input/OutputLevel
Rating:800mVp-p±IO%
(Outputlevelatthetimeof75Q tennination)
SCRAMBLEDNRZItype
4. TransmittingSpeed 270Mb/s
5. QuantityingBitNumber !Obits
. 6. OutputImpedance
7. Returnloss
750
Above15dB(~270MHz)
5

6
HTM-1505R/HTM-1505CS
(4) DecoderInputModule(Option]
· DE-801NTSC3-lineCOMdecodermodule
1. Input/outputTerminal BNC3-lines(Loopthrough)
2. SignalFormat
3. InputLevel
4. InputImpedance
NTSCCompositesignal
VS: l.0Vp-pPositivePolarity
V: 0.7Vp-pPositivePolarity
Highimpedancebridgeconnectionor750.tennination
[750.tenninationplugisoption].
5.Rerumloss Above46dB(I0MHz)
(5) AudioLevelMeterModule(Option]
DAM-5044chEmbeddedaudiolevelmeter
• DAM-5088chEmbeddedaudiolevelmeter
1.Formatscorrespondingtoembedded input
SMPTE272M:480i/59.94 (4:2:2)
576i/50 (4:2:2)
SMPTE299M:I035i/60,59.94
1080i/60,59.94
1080i/50
1080i/48,47.95
720p/60,59.94
2. FormatChange AutomaticChange
3. Reference Level -20dBFS
4. NumberofChannels
DAM-504: 4channels
DAM-508: 8channels
5. IndicationSegment 13-segments
6. DisplayDevice
-=~-25dB: GreenLED
-20~- 0dB: AmberLED
2.3Options_
111DK-801
llllDK-802N
111DK-8012
1111DKH-501/502
111DE-801
■ DE-802
■ DHC-802
• SRC-301A
1111DCH-501
■ RCT-20A
11 EX-801A
4:2:2 componentmodule
4Fscdigitalcomposite(NTSC)module
4:2:2/digitalmodule
HD-SDIModule
NTSC3-IineCOMdecodermodule
PALCOMdecodermodule
Dualcomponentmodule
(forYPbPr/RGBinputexpansion)
Serialremotecontroller
YPbPr/RGBinputmoduleforI inputexpansion
Infraredremotecontroller
ASP-80autoset-upprobe
Ill ASP-80 Autosetcupprobe
Ill RS-1550CS 15typerack-mountedadapter

-----------llllllllllllllllllillllllil-lllllllllllllll___________HTM-1505R/HTM-1505CS
2.4 External View
(1) HTM-1505R
[Withoutembeddedaudiolevelmeter]
l,a9'6H
I
'
I
i
'
I
'
I-
'
I
i
'
I
'
I
'
I @)
@m.@1@~~~
®~
©i.<0)~(@~
@ru@i@~@E
@
®
®
•©.•®)'@fs ~ s s 1 -•
i clJ lb"O"O"Ql[l!H®
@) L L
®I
~© 1~
~
®
\ I
.
f-
.
00
::i
+f
Ln
-
Ln
0
I-,
0lO:OO:g<?<??? I-'
g__g .o.a .aa •··
I
'
! ::i
---=i-----I- =t
---- ----
I
'
I
i I-,
□ .. □.□
I-'
i;g st
....
'Ill' " ...
" C, ....
........
....
....
~
.---
oz
= ::i
:.
. ...
...
~
1-,
I-'
.
@)
I , l
• llll@lillJGll;ll4.> •
.. 4,)(ll>O) ..
® @@@ ~@@tQ 1D1e
• O lilll ll!Clll
7

8
HTM-1505R/HTM-1505CS
(2) HTM-1505R
[Withembeddedaudiolevelmete1j
Ct) ;"'7@1® ~ ~ ~
@~ ©i®)~~
®rn<O)i(Q) ~~
i I I 111
O O, 0000,
0 O• 0000•
0 O• 0000•
gg:J= gm.·I
0 O• 0000•
0 O• 0000•
0 O• 0000•
0 O• 0000•
O O• 0000•
0 O· 0000·
0 O· 0000·
o o- 0000-
Ct)
@
@
-
~
..
...
-
...
i•©~fs s s , r ,.
~ ·o•o·o·a~a•i
@ 1 ; I ·- ii@
L L
®I
~@ ,~
~
@
@
\ ,..
'
if
-
r, i-,
D:~:~:~ ~ :g<?<?<?<?
µ
g__g ,o .a .a a •··
l!;;; I
lli
1 '
I
~
'
~~
---=1----t-
~
-,_____ ---- ,-
1~: I
'
!~·
~
-,
I..
□ .. □. □
_,
V
1.g9[
-. . ...
'Ill' -...
• "' ...
...
...
..
....
--
"""7f
=
~
..
"'
. en
...
e:=
1, h
µ
.
@
I I
.r.-:J
.. .
.a·
oD l.:i:J
• •
Rii M--~
. .
.@@0000@0 .
• fl!!l@lllil@fl!!I@ •
., @@@ .,
@@@
.. .0000. D.,
..@ll!!I ll!Clll • tJ
.

-llllllllllllllllllllllll-iliBl!llll\\'lllllllllllllllllll!llllllllllllllllll!lllllllll\lillll-lllllllil!l!llllllllllllllllll!la••-------- HTM-1505R/HTM-1505CS
(3) HTM-1505CS
[Withoutembeddedaudiolevelmeter]
0
D
0
0
00
I.
I
mOSE
I ...
I
'
I
'
:I
..
...
...
i
u;uo,au mui l
I =
.,.
/
I ®m-~~~@@
@
@~ (®i(®@i@@i@ @@
; -~•@!@fs s s s §
L.lJ v·o·o·o~a~i
@ . L ., '• b@
L
@~ @1@ 1~ B @
\
'
I
'
I ..
--·i·-- .,,,
--oo -
C'<
'
I
i
□
'
' :II.
1· t,O91
t,OOE t•S'61
..
! 1~
® ::f:::f
.....
....,-i---
@ ®
1u
0
oD .,.
• •
• • •
• @@@@@@@@ •
" @@@@@@ ..
@@~
.. D~~a.D.
.. @@ i!Cl!I ..
1•0~ :I
...
C,
en
=
r,
-
9

HTM-1505R/HTM-1505CS
(4) HTM-1SOSCS
[Withembeddedaudiolevelmeter]
II I 1111
o o, 0000,
o o• oooo,
o o• 0000,
~ ~:Im~==1
o o• 1 oooo•i
o o• .. ooao, :!I
□ □• 0000• El
0 □• 0000
0 □• □□ 00•
o o- 0000-
0 a- □□ o □-
a □• ooo □-
I
moss
I ...
'
I
'
I
i
:I
..
...
-
...
I
{!,JULJl,JO mUP
'
I ...
~
/ -
/@~ii~~~~
@
@~ @i@@i@@i@ @@
I;@.;@50fs s s s i •
cti in·o·o·a![D]~E
® t. o '• U@
L
@~ @1@ 1~
~
@
\
10
' 0 p
13-
D '
11
I
i
~
n ..
I c:,
u --·1·-- ---
II ....
Ill I
Ill '
"'' I
I fc;-,
....
I. :Ij.
"6I
-...
L L~
® ::f::1
........
--~
I•OZ :I
..
c:,
...
...
~
....
® ®
1 1u
0
oD·•· ~
• •
• • •
• @@@@@@@@ •
.. @)@) • @)@)@) ...
@@e
• oeoa.lD!..
.. @)@) liD!I •

HTM-1505R/HTM-1505CS
3.lnstallatkm
CAUTION To assure safety, make connection after turning off each equipment.
3.1 Connection to external equipment
(1)Standardmodule(MPU,VIDEO PROCESS)
-------------- MPUmodule
,~-©-,C.-,·-~··-_--_..__.._,__..__,____..-·_·-"_-..__.._____..-·,_/-_-_·-_·-~_---.._--.._-,l,-.-..----._-,-.- ___-____-i--.;1::~:::::~=~i~followl~-Md fu=~
) REJ.IOTEI IYPbPtlGBR I j
• Insertattachedremoteconnectorhere.
• Forpinconnectionsreferto3-2.
CHA ; • InputRGBcodeorYPbPrsignalhere.
• Formatsthatcanbeinput
CD525i/59.94
@ 625i/50
@ 1035i/59.94(60)
© I0S0i/59.94(60)
@ 720p/59.94(60) (720pcorrespondstoType-lonly.)
• Signalfonnat
SettingofHDTV/SDTVonMENUI -2 isrequired.
For1080ior I035i,settingof 1035i/l080ionMENUI~3isalsorequired.
· SetswitchingofRGBNPbPr on MENUI - 4
· Whenloop-throughconnectionisnotdone,connectterminationplug.
• WhenoptionalDCH-501ismounted,inputof2 channelscanbeperfonned.
• WhensettingRGBNPbPrsignalorcompositesignaltoexternal
synchronization,inputexternalsynchronizin~signalhere.
• Whenloop-throughconnectionisnotdone,connectterminationplug.
•ConnectBNCcablefromserialremotecontrollerSRC-301Ahere.
• Whenloop-throughconnectionismade,amaximumof99 monitorscanbecontrolledindividuallyor collectively.
• Whenloop-throughconnectionisnotmade,connectterminationplug.
• SetmonitorIDonmenu.
11

HTM-1505R/HTM-1505CS
(2)MultiSDIInputmodule
DKM-501*
DKM-501*AV
DKM-501*AVD
1ABSIEBU0UT7
~ CH112
~ CH3/4
~ CH516
~ CH7/8
DKM•501AVO
12
.SDIAJB.signalioput..
· InputHDTVor SDTV(4:2:2)signalintothisconnector.
· Discriminatesinputsignalformatautomaticallyandcontrolsmonitor.
SDI.signalc:>utput
-------- · Outputssignalof channelthatmonitorselectsfromA/Bchannelof inputSDIsignal.
AUb10·tlNEOUT
· Selectone pairchannelfrom4 pairchannelsbymenumanipulationto outputanalogsoundsignalof
2 channelsfromthisconnector.
· UseoutputconnectorXLR-5c11C or equivalent.
· Pinfunctions
lpin:GND
2pin:Evennumberch
4pin: Oddnumberch Hotoutput/3pin:Evennumberch Coldoutput Hotoutput/Spin:Oddnumberch Coldoutput
· Asoutputisofactivebalancetype,connectcoldsideto GNDwhenusinginunbalance.
· OutputsdigitalaudiosignalofAES/EBUformat.
Formatsforconsumerappliances(SPDIF)arenotsupported.
· Whenconnectingto 11ODimpedanceequipment,useconverter.

(3) SD-SDI input module
©
~----~----i
~
YCHA
~
~
yctiB
~
HTM-1505R/HTM-1505CS
.··•DS.-SDIlTJodule.•·.·:···F'ollowing'3.types~reavailahle:
DI Digitalcomponentmodule(DK-801)
D2/D3NTSCdigitalcompositemodule(DK-802N)
· InputSD-SD!signalintothisconnectoraccordingtothefollowingmountedmodules:
CDDK-801 4 :2 :2 SerialDigitalComponentSignal
@ DK-802NNTSCSerialDigitalCompositeSignal
® Correspondsto bothsignalsofDK-8012 CDand ® (Formatisautomaticallydetected.)
• WhenthismoduleismountedtogetherwithHD-SDImodule,itisassignedassecondslot.
Selectbypressing2ndSLOTswitch.
SD~DI 13signal output
· OutputsSD-SDIsignalinputintoBchannei
fromthisconnector.
· Itispossibletooutputsignalsselectedby
monitorfromthisconnectoraccordingto
settingofconnectorinmodule.
[HowtoSet[
NORMAL(Factorydefault) MONITOROUT
(4) NTSC 3-linedecoder input module
DE-801
~
l-CHA
~
w
rCH8
~
~
f-c,c
~
· InputNTSCanalogcompositesignalintothisconnector.
· Whenloop-throughconnectionisnotmade,connectterminationplug.
• Whenusingbyexternalsynchronization,inputexternalsynchronizingsignalintoSYNCinput
connectorofVIDEOPROCESSmoduleof( I).
13

HTM-1505R/HTM-1505CS
(5) Dual component input module
DCH-501
CHB
~
rV/G
~
~
rPhlS
~
~
rP,IR
~
14
YPbPr/GBRB channel input
· inputRGBsignalorYpbPrsignalintothisconnector.
· Whenloop-throughconnectionisnotmade,connectterminationplug.
CDs2si 159.94
® 625i/50
@ 1035i/59.94,60
@ IOS0i/59.94,60
@ 720p/ 59.94(60) ..· (CorrespondstoType-Ionly.)
• Tosetsignalformat,settingofl-IDTV/SDTVon MENU 1-2isrequired.
- For IOS0ior 1035i,settingof I035i/I080ion MENU1-3isalsorequired.
• SetswitchingofRGB or YPbPronMENU
· When using by external synchronization,input external synchronizingsignal into SYNC input
connectorof G).

...... U/11 . LUI m - iii& . I
3.2Connection of parallel remote connector
(1) Pin function
~
1 g11
0 0
0
0 0
0
0 0
0
0 0
0
~ 10 1°s
~
GND
CH-B ON
CH-C ON
Green TALLYON
RGB/YpbPr ON
SD-SDI ON
MONO ON
RGB ON
EXT-SYNC ON
16: 9 ON
NC
Viewfromrearsideofmonitor MARKER ON
SHADOW ON
RedTALLY ON
HD-SDI/MULTISDI ON
Green TallyON
< Wiringof remote connector>
Tochangeselectedinputto channelB,connecttoNo. I pin.
*WhenbothNo. 2 and3 pinsareopen,choosechannelA
TochangeselectedinputtochannelC,connecttoNo. I pin.
*WhenbothNo.2 and3 pinsareopen,choosechannelA
TotumonGreenTALLY,connecttoNo. I pin.
Toselectcomponentvideo(RGB/YpbPr)input,connecttoNo. I pin.
ToswitchbetweenchannelsNB, usetogetherwithNo. 2 pin.
ii HTM-1505R/HTM-1505CS
* WhenNo. 5,No.6 andNo. 15pinsareallopen,selectanalogcomposite.
Toselectdigitalvideo(SD-SDI)input,connecttoNo. I pin.
ToswitchbetweenchmmelsNB, usetogetherwithNo. 2 pin.
*WhenNo.5,No.6 andNo. 15pinsareallopen,selectanalogcomposite.
TochangesettingofCOLOR/MONOto RGB,connecttoNo. I pin.
TochangesettingofYpbPr/RGBto RGB,connecttoNo. I pin.
Tochangesynchronizationof mialoginputtoexternalsynchronization(EXTSYNC),connecttoNo. I pin.
Tochangesettingofaspect(4:3/16:9)to 16:9,connecttoNo. I pin.
Idleterminal
Toturnon4:3market;connecttoNo. I pin.
TotumonSHADOW,connecttoNo. I pin.
ToturnonRTALLY,connecttoNo. I pin.
ToselectHD-SDIorMulti-SDIinputmodule,connecttoNo. I pin.
ToswitchbetweenchannelsNB, usetogetherwithNo. 2 pin.
*WhenNo. 5,6 and 15pinsm·eallopen,selectanalogcomposite.
(2) Connectors used (standard accessories)
O-sub 15pin(male)miniaturetype
• Connector: HDB-15M(3011-15)
• Case: HE-C8-J9-F2-I
madebyJapm1AviationElectronicsIndustry,Ltd
madebyJapm1AviationElectronicslndust1y,Ltd.
15

HTM-1505R/HTM-1505CS
16
[HTM-1505R model]
4.1 Power supply G) FUSE
/n, Providedforovercun-entprotection.
:~}~ovQ-:::::1-----------:_ __If_it_h_as_fi._1s_e_d_,1_·e_p_ai_r_fa_u_lty_p_ru_t_ru_1_d_t1_1e_·n_i_n_se_rt_ra_te_d_4_A_(2_5_0_V_)_fu_·s_e_._________ ~
CD p~~~R
[D-----~--------i Cg)MAIN POWER Switch
Whenoperatingmonitor.turnonthisswitch,andthenturnon POWERswitchon frontpruiel.
Q) AC POWER Input Connector
InsertattachedACcablehereru1dsupplyACpowerto it.
@ Locking fixture
\\---;;i::;:::::;:;'.::==,!
1....,.1--------f TopreventcomingoffofACplug,lockwiththisfixtureutterinsertingACplug.
AC100-120V
Fig.4-1 Poweruniton rearpanel
4.2 Name and function of front left panel
□
Fig.4-1 Frontleftpanel
G) Infrared sensor window
InfraredsensorwindowforRCT-20A wirelessremotecontrolle1:
Cg)NO BURST LED
Operatesonlywhencompositeinputsignalisselected.
Lightsupwhennoburstisaddedto selectedcompositesignal(monochromesignal),or
whencolor-killercircuitisoperated.
Q) OVERLOAD
_LightsupwhenABLcircuitisoperated(withbrightnessexcessivelyincreased).
WhenmonitoriscontinuouslyusedwiththisLEDturnedon fora longperiodoftime,
CRTmaydegrade.Usewithbrightnesslowered.
@ DEGAUSS Switch
TodemagnetizeCRT,turniton.
(Whenpoweristurnedon,monitorperformsdemagnetizingofCRTautomatically.)
Pressingthisswitchcontinuouslyisinetlective.
Todemagnetizesequentially,pressthisswitchagainalterlapseof2 to3 minutes.
@ POWER Switch and LED
UsedtoturnON/OFFpowerto monitor. LEDison whenpowersupplyisturnedon.
Whenstrutingmonitor,besuretoturnon MAINPOWERswitchonrearpruiel.
Usually,turnON/OFFwiththisswitch.