Ikelite 5650 User manual

2
3 4
Congratulations on your purchase of an Ikelite Compact ideo
Housing. Ikelite has over 45 years of experience in the underwater
photographic, video, and lighting market.
Our products are
designed and built in
the USA by Ikelite for
both the professional
and amateur.
The clear housing
permits instant visual
inspection of the
camcorder and all
sealing surfaces as
well as complete
monitoring of controls
and camcorder LCD
screens.
Ikelite Compact ideo
Housings are neutrally
buoyant in salt water
for stability. This
housing has been
water pressure tested at the factory. All camera controls are fully
functional through the housing which is water pressure tested to
200' (60m).
Ikelite Compact ideo Housing
i n s t r u c t i o n m a n u a l
##55665500..0011 JJCC PPiiccssiioo GGCC--FFMM11 iiddeeoo CCaammeerraa
##55665500..0022 JJCC PPiiccssiioo GGCC--FFMM11 iiddeeoo PPaacckkaaggee
PPlleeaassee RReeaadd
We suggest that you read this instruction booklet thoroughly
before use. If you are new to underwater photography be sure
to read the General and Photo Tips.
We also suggest that you read the J C Basic User Guide
thoroughly to have a full understanding of where each
camcorder control is located, and what function each control
provides.
CCaammeerraa SSeettuupp
- Turn off the camcorder. Connect the camcorder to a computer
with the USB cable to fully charge the camcorder battery.
- Set the Date and Time (page 9 of your J C Basic User Guide).
- To assure that your camcorder is operating properly, try
recording and playback modes before placing your camera in
the Ikelite Compact ideo Housing.
H
Ho ou us si in ng g S Si iz ze e a an nd d W We ei ig gh ht t: :
5.5" wide x 4.25" high x 3.0" deep (including controls and lens port).
1
4cm x 11cm x 7.6cm.
Housing with camera weighs less than 1.25lb (0.56kg) above water.
Neutrally buoyant underwater.
OOppeenniinngg tthhee HHoouussiinngg
1. Place the housing face down in your lap or on a flat surface.
2. Depress opposing latch buttons simultaneously to open
housing. Once the latch is unlocked, rotate the latch handle up
and away from the housing until it stops. This motion will also
break the housing o-ring seal and open the housing back
slightly.
NNOOTTEE::Latch must be rotated to the fully open position to assure
easy opening of the back. Rotate the hinged back to it’s open
position.
Top iew
latch closed
Top iew
latch opened
Latch
Button
PUSH TO
UNLOCK
Latch
Button
Latch in open
position
O-ring
Housing Back - Side View
MMaaiinn HHoouussiinngg OO--rriinngg
Check to see that there is an o-ring on the housing back and
that it is clean, lightly lubed, and in its proper location.
OO--rriinngg MMaaiinntteennaannccee
We recommend that you clean the main housing o-ring and
o-ring channel before each day of diving.
1. To remove the o-ring, place your index finger and thumb on the
o-ring as shown (Figure A, Page #5).
2. Squeeze the o-ring into a loop by pressing down on the o-ring
and squeezing your index finger and thumb together (Figure B,
Page #5).
3. Grab the o-ring loop with your other hand and remove the
o-ring from the housing back.
4. Wipe the o-ring channel clean with a paper towel, napkin, or
lint-free wiping cloth .
5. Clean and lightly lube the o-ring. Use Ikelite lube only (supplied
with housing).
6. ery lightly lube the o-ring sealing surface on the housing front.
CCAAUUTTIIOONN::Never use a screwdriver or metal object to remove the
main housing o-ring. This could damage the housing and o-ring,
which could result in a leak.

7
5 6
8
FFiigguurree AA
FFiigguurree BB
Thumb
Index Finger
O
O- -r ri in ng g M Ma ai in nt te en na an nc ce e ((ccoonntt..))
O-ring removal illustrations: Figures A & B
O-ring
Squeeze Index Finger
and Thumb together
to form O-ring loop
Index Finger
Thumb
O-ring
CClloossiinngg tthhee HHoouussiinngg
Rotate the hinged back onto the housing front. Close the latch
and make sure it locks. Latch will “click” into it’s locked position.
Latch buttons will NOT be depressed when latch is properly
locked.
Latch in “locked” position
Latch Button
Latch Button
PUSHTO
UNLOCK
CamerainHousingFront
JVC
I
In ns st ta al ll li in ng g t th he e C Ca am me er ra a
Place the camera face down into the front housing ribs as shown.
[1] Power Button
[2] Up Button
[3] Select Button
[7] Right Button
[8] Delete Button
[9] Down Button
[10] Index Button
Made in
USA
I
K
E
L
I
T
E
1
2
34
567
10
89
[4] Video/Still Button
[5] Left Button
[6] Record Button
Back View
Lanyard
Latch
Focus Switching
Lever
HHoouussiinngg CCoonnttrroollssCChheecckk MMaaiinn OO--rriinngg SSeeaall aanndd CCoonnttrroollss
Once the housing has been closed, look at the main housing o-ring
seal from the “top view” as seen on page #4. Rotate the housing
360 degrees and note the o-ring seal by looking through the clear
housing. A good seal should appear as a solid black line.
Make sure the housing controls line up with the camera controls.
TTuurrnn CCaammeerraa OOnn
Turn the camera on and operate each of the housing controls to
get a feel for using the camera in the housing. Operate the camera
above water with the camera in the housing.
** YYoouu aarree nnooww rreeaaddyy ttoo sshhoooott uunnddeerrwwaatteerr vviiddeeoo!!
LLeennss PPoorrtt
Treat the glass in the lens port as a camera lens. After use, rinse
and gently dry the outside lens port to avoid water spotting. To
clean, use a mild soap solution or lens cleaner. Do not rinse the
inside port glass.
Do not use alcohol or window cleaner on the Lens
Port.
UURR--PPrroo FFiilltteerr
The included UR/Pro color correcting filter
for tropical blue water settings, replaces
some of the reds and warm natural tones
that would otherwise be lost underwater.
Effective in relatively shallow, sunny
conditions with or without a ideo Light.
The #6441.71 removable color filter is available separately for
use in green water settings.
NNOOTTEE::Make sure no air bubbles are trapped between the UR-Pro
Filter and housing port. If so, remove the filter underwater,
wipe away the bubbles, and re-install filter on the housing port.
UR-Pro Filter Housing
Port
FFooccuuss SSwwiittcchhiinngg LLeevveerr
Macro Recording: Pull out on the housing lever control knob and
rotate counter-clockwise until it stops. Push knob back in and
rotate clockwise until “Flower” icon appears in the LCD screen.
Normal Recording: Pull out on the housing lever control knob and
rotate clockwise until it stops. Push knob back in and rotate
counter-clockwise until “Flower” icon disappears in the LCD
screen.

HHoouussiinngg MMaaiinntteennaannccee
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
1. DDoo NNoottleave the camcorder and housing in direct sunlight for
prolonged periods. Heat may damage the camcorder.
2. DDoo NNoottship the camcorder in the housing.
3 Keep the back o-ring clean and lightly lubricated. Only apply
enough lubricant to make the o-ring feel slick. DDoo NNoott ssttrreettcchh
tthhee oo--rriinngg. This light coating of lubricant will help to keep the
o-ring from drying out and reduce friction when opening and
closing the housing. Keep the area where the o-ring fits and the
sealing surface of the housing clean.
4 Rinse the housing exterior thoroughly in fresh water after each
salt water use. Dry with a soft cloth. Dry lens port to eliminate
water spotting.
After several uses in salt water, soak the housing exterior in a
mild soap solution, rinse and dry before storage. When storing
the housing, remove the back o-ring, lightly lubricate and place
in a plastic bag. Place the plastic bag with o-ring inside the
housing for safe keeping.
PPuusshh bbuuttttoonn ccoonnttrroollssrequire no maintenance other than rinsing in
fresh water after saltwater use. If a push button control
becomes difficult to push, or if it sticks when depressed, soak
the housing in luke warm fresh water. After a few minutes
operate the push button. If this does not correct the problem,
return the housing to Ikelite for routine maintenance.
910
11 12
Complete information regarding optional accessories available at
http://www.ikelite.com/web_two/jvc_fm1.html
IIkkeelliittee WW--2200 WWiiddee--AAnnggllee CCoonnvveerrssiioonn LLeennss ##66442200
For increased angle of coverage, color, and clari-
ty, add the Ikelite W-20 #6420, or other 67mm
wide-angle conversion lenses. Ikelite 67mm
Threaded Port Adapter ##99330066..7788is required to
attach 67mm conversion lenses to the housing
port.
##99330066..7788 6677mmmm TThhrreeaaddeedd PPoorrtt AAddaapptteerr
Allows attaching Ikelite W-20 Wide-Angle
Conversion Lens #6420 with 67mm threads.
Also allows attachment of Epoque, Type II Inon screw-on lenses,
and macro lenses or diopters with 67mm threads. Includes larger
size removable flash deflector.
##99330066..8855 BBaayyoonneett PPoorrtt AAddaapptteerr
Allows attaching INON UWL-105 AD, UWL-100 28AD, and
UFL-165AD bayonet mount lenses.
NNOOTTEE::Slight edge softness around the picture edges is normal in
some situations. Slight vignetting can occur with the camera in it’s
widest angle setting when using conversion lenses. Zoom in to
eliminate.
OOppttiioonnaall AAcccceessssoorriieess
M
Ma ai in n H Ho ou us si in ng g O O- -r ri in ng g # #
0
01 1
3
3
2
2. .4 45 5
O-rings last for several years if properly maintained (See
housing maintenance page #12). Always carry a spare in case
your housing o-ring becomes damaged or lost.
IIkkeelliittee LLuubbee ##55002200 ((44 -- 11cccc ttuubbeess))
For light lubrication of the main housing o-ring.
OOppttiioonnaall AAcccceessssoorriieess ((ccoonntt..))
U
UR R/ /P Pr ro o B Bl lu ue e W Wa at te er r F Fi il lt te er r # #
6
64 44 41 1
.
.3 3
1
1
((iinncclluuddeedd wwiitthh hhoouussiinngg))
(#6441.42 for W-20 Accessory Lens)
The UR/Pro color correcting filter is designed to restore some of
the warm colors filtered out by the water. For use with
available light and video lite.
UURR//PPrroo GGrreeeenn WWaatteerr FFiilltteerr ##66444411..7711
(#6441.82 for W-20 Accessory Lens)
Enhances contrast and alters the color of green water to give
your subject a rich, natural tone. For use with available light
and video lite.
Dual Tray
#9523.52
Single Tray
#9523.51
iiddeeoo CCoommppaacctt TTrraayy ##99552233..5511 // DDuuaall TTrraayy ##99552233..5522 //
HHaannddllee ##99553300..11
Handle
#9530.1
Attaches to the Ikelite Compact ideo Housing.
Allows the attachment of one or two Pro- 8
ideo Lites, or the Pro ideo Lite 3. Hardware
included for easy attachment to your housing.
Lites can be attached to a single or dual tray,
with or without Handle(s).
Pro- 8
Lite
OOppttiioonnaall AAcccceessssoorriieess ((ccoonntt..))
Once the ideo Compact
Tray is attached to the
housing, the Pro- 8 Flex
Arm easily attaches to the
Flex Mount Ball as shown.
Once attached, the Pro- 8
Lite can be repositioned
effortlessly.
HHoouussiinngg wwiitthh TTrraayy aattttaacchheedd
IKELITE
LED
PRO-V8
Flex Arm
Flex Mount
Ball
Housing
Pro- 8 Lite
PPrroo--88 iiddeeoo LLiittee ##66332200
The Pro- 8 LED is the easiest and most affordable way to add
valuable light to your system.The flexible pop-bead flex arm allows
the light to be repositioned effortlessly. The included flex mount
ball attaches to the ideo Compact Tray. For more light, add a
second Pro- 8 LED or the Pro ideo Lite 3 system with the
#9523.52 Dual Tray. Requires the #9523.51 ideo Compact Tray,
sold separately.

13
##
JJCC GGCC--FFMM11 CCaammccoorrddeerr--0033--00661100
GGeenneerraall TTiippss
1. Before placing your camcorder in the housing, it is a good idea
to immerse the closed housing in a bucket or rinse tank to make
sure it is watertight.
2. Due to the power required to operate the camera and LCD
screen, it is a good idea to start each dive with a fully charged
camcorder.
3. As soon as you enter the water, take a moment and check the
housing to see that it is properly sealed.
4. Next, check to see if there are any bubbles on the face of the
lens port. If there are, take your finger and remove them. If
there are bubbles on the lens port they can produce soft focus
spots in your video.
NNOOTTEE::Fogging of the port glass may occur due to a variety of
environmental factors. To prevent fogging issues, always
assemble the housing in a cool, dry area, and keep the housing
out of direct sunlight. If fogging persists, insert a fresh dessicant
packet inside the housing before each day of diving (dessicant
packages are not available from Ikelite, however most camera
stores carry them).
PPhhoottoo TTiippss
The number one rule in underwater videography is to eliminate
as much water between the camcorder and subject as possible.
Get as close as you can to the subject, then use the zoom if
necessary.
I
Ik ke el li it te e L Li im mi it te ed d W Wa ar rr ra an nt ty y
This Ikelite product is warranted against any manufacturing
defects for a period of one year from the original date of purchase.
Defective products should be returned prepaid to Ikelite. Ikelite
will, at its discretion, repair or replace such products, and will
return to customer prepaid. All other claims of any nature are not
covered. Housing is pressure tested and warranted to 200’ (60m)
maximum underwater depth. Except as mentioned above, no other
warranty expressed or implied, applies to this Ikelite product.
RReettuurrnniinngg PPrroodduuccttss ffoorr SSeerrvviiccee
Ikelite is most interested in preforming any service to assure that
all products perform as intended. For repair or service, return the
product to the address below with your name, address, phone
number and a brief description of the problem. Evidence of
purchase date must be provided to obtain warranty service.
Normal service time is approximately 2-3 weeks.
IIkkeelliittee UUnnddeerrwwaatteerr SSyysstteemmss
5500 WW 3333rrdd SSttrreeeett
IInnddiiaannaappoolliiss,, IINN 4466220088 UUSSAA
WWhheenn rreettuurrnniinngg pprroodduuccttss,, sseenndd ““aattttnn.. RReeppaaiirr DDeepptt..””
331177--992233--44552233
““ggeenneerraall qquueessttiioonnss”” ee--mmaaiill:: iikkeelliittee@@iikkeelliittee..ccoomm
wwwwww..iikkeelliittee..ccoomm