iLive ISB180 v2448-01 User manual

Carry strap
Portable Fabric Wireless Speaker
User’s Guide for Model ISB180 v2448-01
Controls
To charge the internal battery, plug the USB charging cable
into the DC Power Input on the speaker and a powered on
computer or USB power adapter (not included) and standard
power outlet. Charging time is approximately 6 hours 30min.
Battery life is approximately 20 hours at 50% volume.
When the battery is low a voice will announce“Low Battery,”
then the unit will automatically power OFF.
While the unit is charging it will display a solid red light. When
the battery is fully charged the light will turn o.
Features
• Bluetooth wireless 5.0: range 33 ft.
• Micro SD card port
• Carry strap
• Voice prompts
• Volume wheel
• Built-in rechargeable battery: approximately 20 hrs of
playtime at 50% volume
• Micro-USB port for battery recharge
Includes
• User’s Guide
• Micro-USB to USB charging cable
Aux In
Requires a 3.5mm audio cable (not included).
1. Connect a 3.5mm audio cable to the Aux In on the unit
and the audio output/headphone jack on an audio
device.
2. The speaker will automatically switch to Aux Mode and
The Pairing/Source Indicator LED will change to green.
3. Use the controls on the connected device to select and
play audio. Be sure the volume on your connected device
is audible when you begin playing.
1. Play/Pair: Press to play/ pause tracks. Press and hold to
enter pairing mode.
2. Skip: Press to skip audio tracks.
3. Power/Source: Press and hold to power ON and OFF.
Press to change source modes to Bluetooth, Aux, or
Micro SD.
4. Volume Wheel: Spin volume wheel clockwise to raise
volume level. Spin counter-clockwise to lower volume
level.
5. Pairing/Source Indicator LED.
6. Charging Indicator LED.
4
5
1
3
2
6

Customer Support
Customer Service: 1-888-999-4215 | Email Support: prodinfo@
dpiinc.com | Email Parts: [email protected]
For Warranty Information and the most up-to-date version of
this User’s Guide, go to www.iLiveElectronics.com
To download this User’s Guide in English, Spanish, or French, or
to get answers to frequently asked questions, visit the support
section at: www.iLiveElectronics.com
Para descargar este Manual del Usuario en inglés, español y
francés, o para obtener respuestas a preguntas frecuentes,
visite la sección de apoyo en: www.iLiveElectronics.com
Pour télécharger ce guide de l’utilisateur en anglais, espagnol
ou français, ou pour obtenir des réponses à des questions
fréquemment posées, consultez la rubrique d’assistance sur:
www.iLiveElectronics.com
Copyright © 2019 Digital Products
International (DPI, Inc.) All other trademarks
appearing herein are the property of their
respective owners. Specications are subject
to change without notice.
FCC Warnings
WARNING: Changes or modications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings
• WARNING: To prevent re or shock hazards, do not expose this
unit to rain or moisture.
• WARNING : Where the mains plug or appliance coupler is used
as the disconnect device, such disconnect device shall remain
readily operable.
• Lithium batteries, like all rechargeable batteries, are recyclable
and should be recycled or disposed of according to state and local
guidelines. They should never be disposed of in normal household
waste, and they should never be incinerated, as they might
explode. Contact your local government for disposal or recycling
practices in your area.
WARNING: This product can expose you to chemicals
including lead, which is known to the State of California
to cause cancer and birth defects or other reproductive
harm. For more information go to www.P65Warnings.
ca.gov. This product meets and complies with all Federal
regulations.
Previously Connected Devices
• To manually pair to another device, press and hold
the Play/Pair button. The speaker will enter pairing
mode and a voice prompt will announce“Bluetooth is
connecting,” when ready to pair.
• The speaker can remember multiple Bluetooth devices
and will always try to re-connect to the last device used.
• To re-connect to a dierent device, turn o Bluetooth on
unwanted devices, then access the Bluetooth settings
menu on the device you wish to use and select ISB180.
Made
Green
Pairing & Playing Bluetooth Audio
1. When rst powered on, the speaker defaults to Bluetooth
Mode and is ready to pair automatically. When pairing,
remain within 3 feet of the Bluetooth device.
2. Using the controls on your Bluetooth device, select
ISB180 in the Bluetooth Settings to pair. If need be, refer
to the user’s manual for your specic device for more
information.
3. When successfully paired, a voice will announce,
“Bluetooth is connected.”Your Bluetooth device will now
be heard through the speaker.
4. Use the controls on the connected Bluetooth device to
select and play audio. Use the speaker controls or the
connected Bluetooth device to play, pause, and adjust
the volume level.
5. After initial pairing, the speaker will automatically
connect to the last Bluetooth device used whenever it is
in Bluetooth Mode. Note: If your device should become
unpaired or you nd it is unable to connect, press and
hold the Pair button to enter to Pairing Mode. A voice
will announce,“Bluetooth is connecting,” and you can
connect to the speaker manually.
Micro SD Memory Card
1. Load a Micro SD memory card into the Micro SD memory
card port. The speaker will automatically switch to SD
Card Mode, indicated by a voice prompt, and begin
playing media on the card.
2. Use the controls on the speaker to play, pause, and skip
audio on the card.