illumina TST0092B User manual

ISSUED 05-2014
PACKAGE CONTENTS
1of5
WARNING:
CAUTION:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
● Do not touch the bulb with bare hands use a cloth or glove.
WARNINGS AND CAUTIONS
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● (1) 100W Type-A medium base bulb, Alternate (1) CFL bulb.
● Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire
Strippers,electricaltape,safetyglasses.
Bulb Recommended:
Tools Required:
PREPARATION
UM-TST0092B
E
A
B
D
C
PART DESCRIPTION QUANTITY
ACrossbar Assembly
(Pre-assembled to fixture body) 1pc
3pcs
2pcs
1pc
Wire Connector
Outlet Box Screw
Fixture Body
C
D
E
1pc
Green Ground Screw
()Pre-assembled to Crossbar
B

25of
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
(1) 100W
Bulb
(Not Supplied)
Medium
Base
8”
PART NUMBER REPLACEMENT PART DESCRIPTION REQ.
NO.
1G1418PA Glass Panel 4
10”
6.5”
5”SQ.
7”SQ.
4.5”
7” Outlet Box
Center
1
2”

35of
INSTALLATION INSTRUCTIONS
STEP 2:
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (White or Ribbed Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
WHITE OR RIBBED
BLACK (OR RED) WIRE
GROUND WIRE
WHITE OR RIBBED
BLACK OR SMOOTH
GROUND WIRE
FROM HOUSE
FROM HOUSE
FROM HOUSE
FROM FIXTURE
FROM FIXTURE
FROM FIXTURE
Use Wire Connectors to connect the wires.
Mounting
Screw
Backplate
Outlet Box
Mounting Ball
Crossbar
STEP 4:
a. Install the correct bulb referring to fixture markings and/or labels for maximum wattage.
Outlet Box
Crossbar Assembly
Outlet Box Screw
Mounting Screw
Hex Nut
STEP 1:
a. Remove the Crossbar Assembly from the Backplate on
the Fixture Body as shown in STEP 3.
b. Secure the Crossbar Assembly to the Outlet Box with
Outlet Box Screws.
c. Temporarily attach the backplate to the mounting
screws on the Crossbar, securing with the mounting
balls. If the backplate is not snug against the wall,
remove it from the crossbar and adjust the length of the
mounting screws by unscrewing the hex nuts. Turn the
screws in or out of the crossbar until the correct length
is achieved, then re-attach the backplate. Once the
backplate is secure, remove mounting balls and
backplate as shown in STEP 3.
STEP 3:
a. Carefully tuck all wires into the outlet box and position
the backplate of the Fixture Body over the outlet box.
Align the holes in the backplate of the Fixture Body with
the mounting screws attached to the crossbar. Pass the
fixture over the mounting screws and secure by
threading mounting balls onto end of mounting screws.
Tighten until snug.

4OF5
INSTALLATION INSTRUCTIONS
STEP 5:
NOTE: If you need to replace glass panel
a. By unscrewing the Lock Screws, remove the Cage from
the Fixture Hood.
b. Remove the broken Glass Panel inside of the Cage and
insert the replacement Glass Panel.
c. Attach the Cage with Glass Panels back onto the Fixture
Hood and secure with Lock Screws. Hand tighten until
snug.
Mounting Hole
Lock Screw
Cage with
Glass Panels
Fixture
Hood
Hole
Glass Panel
EXTERIOR GRADE
CAULK
MOUNTING BALL
STEP 6:
a. Refer to the following information for caulking instructions:
Please note that you are required to apply a small
amount of Silicone sealer to the threaded side of the
MOUNTING BALLS and then install them onto the
MOUNTING SCREWS.
With the OUTDOOR FIXTURE properly installed in
accordance with supplied Assembly/installation
instructions, proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and
FIXTURE BACKPLATE are free to dirt to caulking. Using
EXTERIOR GRADE CAULK, start on one side of
FIXTURE BACKPLATE and follow contour, were the
FIXTURE BACKPLATE meets the EXTERIOR WALL
SURFACE upward. Proceed to caulk over top of
backplate and down other side.
to ensure proper
moisture drainage.
DO NOT CAULK
BOTTOM OF FIXTURE BACKPLATE

55of
INSTALLATION INSTRUCTIONS
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
EXTERIOR WALL SURFACE