Illuminated Mirrors 100877K5 User manual

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
1
From
www.illuminated-mirrors.uk.com

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
2
400mm Oak Demister
Illuminated Mirror Cabinets
(Model Numbers: 100877K5 & K6)
Thank you for purchasing our illuminated mirror cabinet(s).
To avoid product damage, personal injuries, carefully read, understand, and follow all
the Instructions in this installation guide before installing the product.
Save this manual for future reference.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
3
WARNING!
To avoid the risk of electrocution, please turn off the electricity
supply mains before commencing the installation.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
4
CONTENT
I. STANDARDS
a. Safety Instructions
b. IP Rating
c. Bathroom Zones
II. OAK CABINET PARTS
III. STEP-by-STEP INSTALLATION
Step 1: Unpack the mirror cabinet carefully & lay on a flat surface.
Step 2: Using a screw driver remove top mirror panel by unscrewing bolts on each side.
Step 3: Remove bulb to gain access to fixing holes.
Step 4: Offer cabinet up to required fitting position.
Using level make sure cabinet is horizontal and mark the fixing holes.
Step 5: Drill holes ready for wall plugs (included).
Step 6: Pull 240 volt cable through rear grommet on rear of cabinet and fix cabinet to wall.
Connect cabinet electrics to your power supply.
Step 7: Replace both LED strips / fluorescent bulb.
Step 8: Replace top panel.
Step 9: Add shelves to desired locations.
Step 10: Clean cabinet mirrors and its ready to use!
Note: Please leave a minimum of 10cm between sensor head on side of frame and the nearest
obstacle e.g. a wall, another cabinet, etc., as the sensor will not be able to work properly.
IV. CARE AND CLEANING
V. FAQs

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
5
I. STANDARDS
a. Safety Instructions
Installation of this product can require a qualified electrician. If necessary, hire or
consult a qualified electrician in accordance with the current IEE Wiring Regulations
and UK Building Regulations for assistance before continuing.
Please turn off the electricity supply mains before commencing the installation.
This light fitting is a Class-II product, therefore doesn’t require an earth connection.
Always use the correct type and wattage bulb; never exceed the stated/rated wattage as
this could overheat the transformer.
b. IP rating
The IP Code (or Ingress Protection Rating,sometimes also interpreted as
International Protection Rating) consists of the letters IP followed by two digits or one
digit and one letter and an optional letter. These two digit numbers refer to the level of
protection the product has and it is important that you choose fittings with correct ratings
according to where they are installed within the bathroom.
c. Bathroom Zones
Our illuminated mirror cabinet has special protection against the ingress of moisture
and manufactured to meet IP44 standard, thereby making it suitable for use in Zones 2 and
3 of a bathroom with reference to the below diagram.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
6
II. OAK CABINET PARTS
(Figure i) –Oak Cabinet with closed door.
(Figure ii) –Oak Cabinet with open door.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
7
III. INSTALLATION
Please turn off the electricity supply mains before commencing the installation.
Wiring Colours:
Earth (E)
GREEN
Neutral (N)
BLUE
Live (L)
BROWN
Step 1:
Unpack the mirror cabinet carefully & lay on a flat surface.
Step 2:
Using a screw driver remove top mirror panel by unscrewing bolts on each side.
Step 3:
Remove Fluorescent bulb/LED strip to gain access to fixing holes.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
8
Step 4:
Offer cabinet up to required fitting position.
Using level make sure cabinet is horizontal and mark the fixing holes.
Note: We suggest 2 people for this job.
Step 5:
Drill holes ready for wall plugs (included).

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
9
Step 6:
Pull 240 volt cable through rear grommet on rear of cabinet and fix cabinet to wall.
Connect cabinet electrics to your power supply.
Step 7:
Replace both LED strips / fluorescent bulb.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
10
Step 8:
Replace top panel.
Step 9:
Add shelves to desired locations.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
11
Step 10:
Clean cabinet mirrors and its ready to use!
IV. CARE AND CLEANING
Please be aware when cleaning the mirror surface, do not to use abrasive materials as
these will damage the overall finish.

Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K5 & K6
INSTRUCTION MANUAL
12
V. FAQs
1. What is a LED Mirror?
A LED Mirror uses Energy Saving LED light bulbs. They are Waterproof Rated IP44
for use in bathrooms and include clever technology like, Infra-Red on/off sensors, Anti-
Mist demister pads and a shaver socket.
2. On/Off Infra-Red Sensor?
All our LED Mirrors include Infra-Red on/off Sensor, simply wave your hand to the
sensor and it will instantly powers up the lights and demister pad. You need to wave your
hand 3-6 inches away to On/Off your mirror cabinet.
3. Where is the sensor located?
The sensor is located on the bottom right of the frame and not on the front of the
glass.
4. Can I isolate the sensor so the led's come on with my bathroom lighting?
Yes, Just call us for instructions and we shall email them to you, it's extremely easy!
5. How the Shaver Socket Works?
Shaver Mirrors include a 240 Volt shaver socket for the use of electric shavers and
toothbrushes. The shaver socket includes its own on/off rocker switch which works
separately from the lights and demister pad.
6. Heated Demister Pad Mirrors?
Just turn on the lights via Infra-Red sensor and the heat pad removes the steam from
the glass on the door.
7. How do I activate the demister pad?
The demister pad works automatically when the lights are turned on and off.
8. Is the mirror tinted glass?
No, the mirror is perfectly clear reflective mirror glass.
9. Is the mirror CE & ROHS certified?
Yes!
*****