Iluminar iL1c User manual

USER
MANUAL
iL1c 330W
1-877-540-5588
iluminarlighting.com
[email protected]
IL-A133026-FSG-120

2
CONTENTS
• Observe all safety precautions (see page 10), seek the services of
a qualied electrician, installation professional, or call ILUMINAR
Lighting technicians for assistance.
• DO NOT handle or touch the xture while in use.
• Connect the xture only to the power sources of the appropriate
voltage using the correct AC plug type. Protect power cables from
being pinched, walked on, or otherwise damaged. Be especially
careful where the power cable enters the power outlet to the unit.
Only connect the xture to an electrical outlet or extension cord of
comparable standard and level rating. Connect the xture ONLY to
the power sources of the correct voltage using the plug received.
• The xture should only be cleaned as directed. Always seek service
for your system by qualied service personnel if any of the following
occur:
1. The xture shows a noticeable change in performance.
2. The power-supply cord or plug is damaged.
3. The xture has been dropped, or the exterior is damaged.
Please read this manual thoroughly prior to
installing or operating the ILUMINAR iL1c.
Pre-Install Information ........................................
Technical & Phsyical Specications......................
Hardware & Accessories ....................................
Hanging Instructions ...........................................
Connection Instructions .......................................
PPFD MAP...........................................................
Important Cautions & Warranty ...........................
2
3
4
5
6-7
8-9
10
1-877-540-5588
iluminarlighting.com
[email protected]
© Copyright 2022, ILUMINAR Lighting
Subject to change without notice.
Minimum
46-122cm / 18-48”
TECHNICAL SPECS
iL1c LED SPECTRUM
MOUNTING & COVERAGE
PHYSICAL SPECIFICATIONS
VOLTAGE AND AMPERAGE
VOLTAGE:
SKU:
WATTS:MODEL: 330W
2.6
100-277V
IL-A133026-FSG-120
iluminarlighting.com
Toll Free: 1-877-540-5588
129mm / 5.1”
90mm / 3.5”
200mm / 7.9”
1000mm / 39.38”
1.2m / 4’
0.91m / 3’
PPF 858 μmol/s
Efficacy 2.6 μmol/J
Min Power Factor >0.9
<20%
THD
0.99
1122
Crest Factor
120-277V AC
Heat Output (BTU/h)
Rated Voltage
100-277V
Voltage Range (+/-10%)
Frequency 50 / 60Hz
Dimmable 0-10V Controllable
Ambient Temperature 0 - 35°C / 32-95°F
Relative Humidity 98%
Plug Type Power Cord Sold Seperately
Color Temperature
Length 1000mm
2.85A
39.38”
5.1”
7.9”
18.3lbs
341W
4000k
Color Rendering Index
Width
208V
120V
129mm
1.63A 335W
88
Minimum Mounting Height
Height
240V
200mm
1.41A 332W
18-48” to top of Canopy
Emitter Cooling
Light Distribution +/- 5%
Waterproof Rating
LED Lifespan (90% of Life)
Weight
277V
347V
480V
8.3kg
0.22A 330W
0.99A 340W
0.71A 331W
Passive Thermal Management
125º
iP65 for Damp/Wet Conditions
54,000+ hours
WAVELENGTH NM
LED Lighting Solution

4
HARDWARE AND ACCESSORIES
The iL1c can be hung from steel
cables or can be mounted to a
rack.
Before you begin installation,
check that you have all the
necessary parts to begin.
1 iL1c Fixture
1 Power Supply
2 Hooks
IN THE BOX
1-877-540-5588
iluminarlighting.com
[email protected]
Set the hooks on the beam.
HANGING INSTALLATION
Hang the light into hooks.
1
2
5
© Copyright 2022, ILUMINAR Lighting
Subject to change without notice.

61-877-540-5588
iluminarlighting.com
[email protected]
CONNECTIONS
If you plan to utilize several LEDs in your room or facility, one of the many benets of
the ILUMINAR LED is that you can “daisy chain” one xture to another to save space
and use only one outlet to run several lamps, thus minimizing the amount of cords
used in your space.
If you plan to utilize the ILUMINAR HASH Controller, connect the connections from
the controller to the xture and then connect the Daisy Chain Controller Cable from
xture to xture. Please consult with our lighting layout designers to ensure proper
spacing of outlets for your unique setup.
3
24
1
7
AVAILABLE CABLES
© Copyright 2022, ILUMINAR Lighting
Subject to change without notice.

1-877-540-5588
iluminarlighting.com
[email protected]
8
PPFD MAP
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
Clearance
Qty
Average PPFD
Max PPFD
Min PPFD
Median PPFD
Min/Average
Watts
1.5
1
396.48
827
115
336
29.01
321.7
4
1
143.34
181
102
142.5
71.16
321.7
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
ft
u
μmol/m2/s
μmol/m2/s
μmol/m2/s
μmol/m2/s
%
W
PPFD MAP iL1c 330W at 1.5ft PPFD MAP iL1c 330W at 4ft
9
>=1000 762-1000 581-762 443-581 338-443 258-338 196-258 150-196 <150 >=1000 762-1000 581-762 443-581 338-443 258-338 196-258 150-196 <150
Legend Legend
© Copyright 2022, ILUMINAR Lighting
Subject to change without notice.

10
CAUTION
1. Leave at least one inch of space between the xture and the mounting
area for maximum performance and lifespan.
2. ALWAYS wear protective eyewear when looking directly at the
diodes to prevent eye damage.
3. Only handle, clean or move xture when it’s unplugged and completely
cool.
4. Keep the xture free of dust, debris, deposits to ensure the maximum
potential of the xture.
5. NEVER use cloth to clean the diodes. This will scratch the diodes and
could potentially break or dislodge them.
6. DO NOT use chemicals to clean the xture. Use ONLY low pressure
air or low pressure water to remove dust and debris
7. Do NOT use sulfur vaporizers.
Please read the following list carefully prior to beginning installation.
At ILUMINAR, we stand behind our products and our
technology as well as our customers. All ILUMINAR xtures
are backed by our 5-Year Guarantee. Please visit our website
iluminarlighting.com/warranty for more information.
1-877-540-5588
iluminarlighting.com
[email protected]
GUARANTEE