Image Projection iPro 60E LED Planning guide

1
iPro 60E/80E/100E/150Es LED
Outdoor Gobo Projector
Description
iPro “E” LED projectors are rated IP-65 for outdoor use. To project
an image, a high resolution glass or metal gobo is required. To
order a gobo, e-mail the artwork of the desired image to Info@
UseLight.com. Line-art or vector les are acceptable, as are pixel
les (e.g. .JPEG, .PNG, .TIFF, .PDF, etc.) 300 dpi or better.
Safety Information
• For indoor or outdoor use.
• Prevent direct eye exposure to the light source as it may lead
to injury or blindness.
• Please use caution when handling or touching the unit during
and after operation, as it may heat up.
• Only use power sources that comply with local electrical and
building codes and have proper grounding.
Gobo Specications
• Outer diameter (OD) - 37.5 mm
• Inner or image diameter (ID) - 25 mm
• Gobo thickness: Up to 3 mm
Package Contents
Projector, optical lens and cable with standard 110 Volt plug.
Instruction/User Manual and Specications

2 3
Model:
Voltage:
Lamp (LED):
Rated Frequency:
LED Lamp Life:
Color Temp. (K):
Luminous ux:
Weight:
iPro-60E
110 to 277 V*
60 W
50/60 Hz
30 - 40,000 Hrs
6,000 - 6,500 K
5,400 lm
8 lbs.
iPro-80E
110 to 277 V*
80 W
50/60 Hz
30 - 40,000 Hrs
6,000 - 6,500 K
7,200 lm
8.5 lbs.
iPro-100E
110 to 277 V*
100 W
50/60 Hz
30 - 40,000 Hrs
6,000 - 6,500 K
9,000 lm
8.5 lbs
Warranty
This projector comes with a 1-year warranty that begins on the
date of purchase and includes labor and parts.
Step 1
Unlock the lens lock ring by
unscrewing it counter clockwise.
Then turn the optical lens counter
clockwise until it comes o.
Step 2
Remove the metal pressure clip by
squeezing together the two bent ends.
WARNING: PLEASE USE CAUTION WHEN REMOVING
OR INSTALLING THE PRESSURE CLIP, AS IT MAY SPRING
OR JUMP OUT UNEXPECTEDLY.
Step 3
Place the gobo with image facing
down (reversed) in the gobo slot.
Step 4
Place the metal pressure clip on top of
the gobo and make sure it is pressing
against the gobo evenly.
Gobo Installation
and Exchange
Projector Specications
5 5/16 “ / 135 mm
8 5/8 “ / 213 mm
3 1/2 “ / 87 mm
4 3/8 “ / 111 mm
2 7/8 “ / 72 mm
5 3/4 “ / 146 mm
2 3/8 “ / 60 mm
Mounting bracket
5 1/2 “ / 139 mm
3 1/2 “ / 87 mm
7 3/8 / 188 mm
5 3/8 “ / 136 mm
Lock ring
Heat
sink
Optical lens
2 3/8 “ / 60 mm
Top ViewBottom View
Side ViewFront View
iPro-150Es
110 to 277 V*
150 W
50/60 Hz
30 - 40,000 Hrs
6,000 - 6,500 K
13,500 lm
8.5 lbs.
* US only - 240 V outside of US

Image Projection • 1109 Ponce de Leon Blvd. • Coral Gables, FL 33134
305-444-0218 • [email protected] • www.UseLight.com
Once the gobo is succesfully installed and the front plate cover is
reattached, rotate the lens clockwise or counter-clockwise until
the image is in focus.
Adjusting the Image Focus
Press the button located on the back of the projector to turn the
rotator ON or OFF.
Turning Rotating Eect ON/OFF
ON
Once the image is in focus, turn the lock ring clockwise until the
rubber gasket is slightly compressed.