IMAGIC IM010101 User manual

R
R
123
4 5 6 0
789
iMagic Touch
Smart Fingerprint & Code Lock
(Electronic Deadbolt)
Installation Guide

WARNING Package Includes:
Installation Video
• Do not use a power drill for installation.
• Install and test the lock with the door open to avoid being locked out.
• Please read all the instructions before contacting customer support.
• Please contact customer support before returning the product to the store.
• DO NOT install the batteries before installing the lock!
Follow the instructions in sequential order!
• If you have previously installed this lock on another door, you must perform a
Factory Default Reset FIRST! See the User Guide for more information.
• This lock is designed for the following operating temperatures:
Outside Lock Body (exterior mounted): -4°F ~ 140°F
Inside Lock Body (interior mounted): -4°F ~ 140°F
Please watch our step by step installation video before attempting to install your
iMagic smart lock at iMagicliving.com.
For technical documents and more
Please visit iMagicliving.com
Tel: [phone]
Email: [email protected]
Need Help?
A
B
G
C
E
I
H
D
I
J
F
Num NumName NameQuantity Quantity
A Exterior Assembly Screw G
Screw H1 2-5/32" (55mm)
Screw H2 2-1/2" (65mm)
Screw I
Screw J
Deadbolt Latch
Strike Plate
Mounting Plate
Interior Assembly
Battery Cover
B
C
D
E
G1
1
1
1
1
1
I
J
4
2
2
2
2
F
H
1 2

Screw Contents
1. New installations (If door is currently drilled, please make sure holes match the
below dimensions):
1" I.D. (25.4 mm) hole on door edge for latch
2-1/8" I.D. (54 mm) hole for the backset: backset can be 2-3/8" (60 mm) or 2-3/4" (70
mm)
1-3/8" (35 mm) to 2" (51 mm) door thickness
2. Installing Latch
A. Adjust the length of latch if needed according to the backset dimension.
A. Determine desired height on door for your new lock. Fold template around edge
of door at desired height.
B. Ensure that centerline of template is at center of door’s edge width. Without
allowing template to move, attach with tape and mark centerline for both holes
(at desired backset and at door’s edge).
C. Having marked holes, remove template and drill a 2-1/8" (54 mm) hole through
door for the backset and a 1" (25.4 mm) hole on the door’s center edge for the
latch.
Name Quantity
AA Alkaline Battery
Keys
Needle
Installation Guide
User Guide
4
2
1
1
1
G
H1
H2
I J
60mm
70mm
(35 mm-50 mm)
1-3/8"-2"
Door thickness
Backset
2-1/8''
1''
25.4 mm
54 mm
2-3/4''(70 mm)
2-3/8''(60 mm)
2-1/8''(54 mm)
1''(25.4 mm)
or
3 4

B1. If you have not installed a lock before：
B2. If door has been mortised previously, insert new latch to test fit. Adjust mortise
as necessary.
C.Secure latch with screws provided (G).
B. Secure strike plate with screws provided (G).
A. Position strike plate in line with latch on door jamb and mark vertical position.
Center strike plate in door jamb. Trace around faceplate and mark centerline for 1"
(25.4 mm) hole. Remove strike plate.
Drill 1" (25.4) hole for latch. Staying within line, chisel wood to roughly 5/64" (2
mm) depth. Check needed depth occasionally by inserting strike plate.
Note:
3. Installing Strike Plate
Insert latch into pocket and trace around faceplate. Remove latch. Staying
within line, chisel wood to roughly 5/32" (4 mm) depth. Check needed depth
occasionally by inserting latch.
Door jamb
5 6

★Note: Use the key to open/close the door to ensure that the door operates
smoothly.
A. Pass the tailpiece vertically through the wire hole of Mounting Plate.
B. Pass the data wire of Exterior Assembly under the latch through the wire hole of
Mounting Plate.
C. Attach the Mounting Plate with screws (H1 or H2). If the position of the Exterior
Assembly is uneven, loosen screws to adjust position and tighten again.
4. Installing Exterior Assembly with Mounting Plate 5. Identify Door Handing and adjust Left(L)/Right(R) switch and the Thumb Turn
Piece.
A. Face the door from outside to determine your Door Handing.
B. Adjust the Left(L)/Right(R) switch of Interior Assembly according to your
Door Handing.
C. Rotate the Thumb Turn Piece according to your Door Handing.
123*
4560
789#
IC wire
123*
4560
789#
IC wire
1 2 3
4 5 6 0
7 8 9
1 2 3
4 5 6 0
7 8 9
Hinge Hinge
Left-handed Right-handed
L
R
L
R
7 8

Congratulations! You have installed your lock correctly!
★Note: Rotate the Thumb Turn Piece to ensure that the door operates smoothly.
6. Installing Interior Assembly
7. Insert Batteries
Insert 4 AA alkaline batteries and slide the battery cover back.
8. Check you have installed the lock correctly
A. Remove the battery cover.
B. Connect the data wires of Interior Assembly and Exterior Assembly.
C. Engage the tailpiece of deadbolt with the turn piece of Interior Assembly.
A. Open with keys/Thumb Turn Piece/admin code(factory default:000000)
successfully.
B. Close with keys/Thumb Turn Piece/touch screen(2 seconds later) successfully.
D. Use 4 screws (J) to attach the Interior Assembly.
Locked Opening
Left-handed
Right-handed
Locked Opening Opened
Opened
9 10