Imagine 2U2 User manual
User Guide
imagine 2U2
Thank you for choosing ! You have a noWire handsfree teleconference unit
based on Bluetooth transmission technology in your hands. may be used
with any mobile phone equipped with Bluetooth supporting the headset- and
handsfree profile. Recommended distance to mobile: 0.5 to 6 meters.
imagine
2U2
®
®
imagine
imagine
2U2
2U2
Support by your
mobile phone is required to make use of all the features in .
Get to know imagine 2U2 Pairing imagine with a mobile
2U2
Push both ends of the volume control.
The blue and yellow lamps flash.
is ready for
pairing with the mobile.
imagine 2U2
- Activate Bluetooth on the mobile
- Search for sound equipment in
- Select ”imagine 2U2”
- Confirm by entering a password: 0000
®
®
Bluetooth menu
Hint: For instructions for your mobile,
see www.imaginenowire.no/mobile
Status indicators
Speaker
Keypad
Outlet for charger
Microphone
UG20en-06Jul04
Volume
Also used for pairing
Hook on/off
Transfer call
between handset
and imagine 2U2
Power and
Microphone Mute
Reset
Restart unit
Before use, imagine 2U2 must be charged with
included charger. Insert plug as illustrated below.
A red light will be
lit. The red light
is turned off when
the unit is fully
charged.
Charging takes
up to 4 hours.
Standby: 450 hours. Operation: 24 hours.
Charging
After charging, the unit may be turned ON.
Turn the unit on/off
Hold down for three seconds.
A responding tone indicates an active unit.
(Use the same procedure for turning the unit OFF)
Bluetooth link
®
Depending on the mobile, the Bluetooth link
may either be constantly active, or activated
when required. A steady or flashing blue light
indicates the status during Standby. When the
unit is active, the blue light is always on. The
yellow light turns on when the unit requires
recharging. The link may be deactivated by
pressing for three seconds.
The link may be reactivated in the same manner.
®
To accept incoming calls or terminate an active
Using imagine 2U2
By pressing the call is rejected.
call, press .
The sound will automatically be transferred to
imagine 2U2. If not, push .
The microphone may be muted. The party at
the other end cannot hear you, and internal
discussions may take place in private.
Push during a conversation to mute the
microphone. To activate it again, press .
A fast flashing yellow light indicates
a muted microphone.
Improper operation
No indication during recharge
Flashing red during recharge
Try resetting the unit by sticking a paper clip through
the hole located between the Volume and the ON/OFF
buttons. Three responding tones will be heard as
the unit is reset.
The battery is fully recharged and no additional
charge is needed.
An error has occurred, which may be caused by
high battery voltage. Disconnect the plug,
wait a while, and try again.
Echo at the far end
Try lowering the volume on .imagine 2U2
Only use chargers supplied by Imagine noWire.
The use of other than original accessories voids
the warranty. The same applies if the unit is
disassembled.
Original accessories are marked as follows:
Charger:
Charger for car:
IMAGINE NOWIRE SWITCHING ADAPTER
JSP6R0V1000
Ambient temperature should be within the range
+5 to +45 C. Keep unit away from liquids and
high humidity. Use only a soft cloth for cleaning.
If it will not be in use for a while, recharge the
unit completely and turn it off before temporary
storage.
00
For additional product information,
please see www.imaginenowire.com
Bluetooth is a trademark owned by Bluetooth SIG, Inc.
®
A flashing or steady yellow light indicates that the
battery need to be recharged. If the battery is
further discharged, three short tones are played
twice, and the unit closes. Recharge with supplied
charger before further use.
Note: During operation a yellow, fast flashing light
indicates a muted microphone, while a steady
yellow light indicates low battery.
Battery status
Troubleshooting
Limited warranty
Safety instructions
To transfer the call from
Press once again to transfer the call back
to
imagine
imagine
2U2
2U2
to the
mobile, give an instant touch.
.
Transfer the call
Voice dialling
Give an instant push to activate voice dialling.
Press for three seconds to redial the last
number.
Redial last number
Muting the microphone
