Imc Accesslinx User manual

About AccessLinX VoIP Gateways

The AccessLinX units are analog gateways with two Voice-over-IP (VoIP)

ports. The unit enables the use of two independent analog telephone lines

or FAX machines to make VoIP phone calls over the Internet or Intranet. In

addition, it enables connecting up to four computers or segments to the net-

work. Local computers are connected via Ethernet 10/100Base-TX ports.

The Uplink connection is via either a 100Base-FX SFP fiber optic connector

or a 10/100Base-TX copper port. All Ethernet ports are connected by an

advanced switching engine that supports VLANs and QoS.

For

complete

installation

and

configuration

information

for

your

AccessLinX,

please

refer

the

User

Guide,

located

the

User

Documentation

CD-RROM,

delivered

with

the

unit.

Installing AccessLinX Units

The figure below shows the connectors on the rear of the AccessLinX unit

as it is deployed in a typical application.

• The RJ-11 telephone ports Phone 1 and Phone 2 connect to the

telephony devices.

• The PSTN (lifeline) port can be connected as a standby to the public

telephone network. In case of power failure, the phone connected to

the Phone1 port will be automatically switched from VoIP to this line,

for regular telephone communication.

• The RJ-45 LAN ports connect to the LAN, to other Access units and to

computers. The LAN4 Uplink port connects to the network.

• The AUX/Console port, if available, is an option to be used by author-

ized technicians to configure the unit via a serial PC port.

WARRANTY

IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free from

defects in materials and workmanship under normal and proper use in accordance with IMC Networks' instructions and direc-

tions for a period of six (6) years after the original date of purchase. This warranty is subject to the limitations set forth below.

At its option, IMC Networks will repair or replace at no charge the product which proves to be defective within such war-

ranty period. This limited warranty shall not apply if the IMC Networks product has been damaged by unreasonable use, acci-

dent, negligence, service or modification by anyone other than an authorized IMC Networks Service Technician or by any other

causes unrelated to defective materials or workmanship. Any replaced or repaired products or parts carry a ninety (90) day

warranty or the remainder of the initial warranty period, whichever is longer.

To receive in-warranty service, the defective product must be received at IMC Networks no later than the end of the war-

ranty period. The product must be accompanied by proof of purchase, satisfactory to IMC Networks, denoting product serial

number and purchase date, a written description of the defect and a Return Merchandise Authorization (RMA) number issued

by IMC Networks. No products will be accepted by IMC Networks which do not have an RMA number. For an RMA number,

contact IMC Networks at PHONE: (800) 624-1070 (in the U.S.) or (949) 465-3000 or FAX: (949) 465-3020. The end-user shall

return the defective product to IMC Networks, freight, customs and handling charges prepaid. End-user agrees to accept all

liability for loss of or damages to the returned product during shipment. IMC Networks shall repair or replace the returned

product, at its option, and return the repaired or new product to the end-user, freight prepaid, via method to be determined

by IMC Networks.

IMC Networks shall not be liable for any costs of procurement of substitute goods, loss of profits, or any incidental, conse-

quential, and/or special damages of any kind resulting from a breach of any applicable express or implied warranty, breach of

any obligation arising from breach of warranty, or otherwise with respect to the manufacture and sale of any IMC Networks

product, whether or not IMC Networks has been advised of the possibility of such loss or damage.

EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, IMC NETWORKS MAKES NO OTHER WARRANTIES,

WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS IMC NETWORKS PRODUCT, INCLUDING WITHOUT LIMITA-

TION ANY SOFTWARE ASSOCIATED OR INCLUDED. IMC NETWORKS SHALL DISREGARD AND NOT BE BOUND BY ANY

REPRESENTATIONS OR WARRANTIES MADE BY ANY OTHER PERSON, INCLUDING EMPLOYEES, DISTRIBUTORS,

RESELLERS OR DEALERS OF IMC NETWORKS, WHICH ARE INCONSISTENT WITH THE WARRANTY SET FORTH ABOVE.

ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

HEREBY LIMITED TO THE DURATION OF THE EXPRESS WARRANTY STATED ABOVE.

Every reasonable effort has been made to ensure that IMC Networks product manuals and promotional materials accu-

rately describe IMC Networks product specifications and capabilities at the time of publication. However, because of ongoing

improvements and updating of IMC Networks products, IMC Networks cannot guarantee the accuracy of printed materials after

the date of publication and disclaims liability for changes, errors or omissions.

FFE D E R A L CCO M M U N I C A T I O N S CCO M M I S S I O N RRA D I O FFR E Q U E N C Y IIN T E R F E R E N C E SST A T E M E N T

This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inter-

ference to radio communications. Operation of this equipment in a residential area is likely to cause harmful inter-

ference in which the user will be required to correct the interference at his own expense.

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to

operate the equipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits.

This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out

in the Radio Interference Regulation of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux

appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère

des Communications du Canada.

IMC Networks •19772 Pauling • Foothill Ranch, CA 92610-2611 USA

TEL: (949) 465-3000 • FAX: (949) 465-3020

www.imcnetworks.com / [email protected]

The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any errors

that may appear in this document. AccessLinX is a trademark of IMC Networks. Other brands or product names may be

trademarks and are the property of their respective companies.

Document Number 52-80422-00 A0 June 2005

Networks

AccessLinX

Installation

Guide

General Information

IMC NETWORKS TECHNICAL SUPPORT

Phone: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada);

+32-16-550880 (Europe)

Fax: (949) 465-3020

E-MMail: [email protected]

Web: www.imcnetworks.com

SPECIFICATIONS

Environmental:

Operating Temperature:

0°C - 40°C (32°F - 104°F)

Storage Temperature: -18° to +70°C (0° to +158°F)

Hunidity: 95% non-condensing

Electrical:

DC adapter input power: 100-240V[email protected] 47-63Hz

DC input power: 5 [email protected] - External power supply

Power Consumption: 10W

Dimensions:

7.36"(W) x 4.45"(L) x 1.71"(H) [18.7(W) x 11.3(D) x 4.35(H) cm]

ELECTROSTATIC DISCHARGE PRECAUTIONS

Electrostatic discharge (ESD) can cause damage to your add-in modules. Always observe the

following precautions when installing or handling an add-in module or any board assembly.

1) Do not remove unit from its protective packaging until you’re ready to install it.

2) Wear an ESD wrist grounding strap before handling any module or component. If you do

not have a wrist strap, maintain grounded contact with the system unit throughout any

procedure requiring ESD protection.

WARNING! Integrated circuits and fiber optic components are extremely susceptible to

electrostatic discharge damage. Do not handle these components directly unless you are a

qualified service technician and use tools and techniques that conform to accepted industry

practices.

3) Hold boards by the edges only; do not touch the electronic components or gold con-

nectors.

4) After removal, always place the boards on a grounded, static free surface, ESD pad or

in a proper ESD bag. Do not slide the board over any surface.

SAFETY CERTIFICATIONS

UULL//CCUULL::Listed to Safety of Information Technology Equipment, Including Electrical Business

Equipment.

CCEE::The products described herein comply with the Council Directive on Electromagnetic

Compatibility (89/336/EEC) and the Council Directive on Electrical Equipment Designed for

use within Certain Voltage Limits (73/23/EEC). Certified to Safety of Information Technology

Equipment, Including Electrical Business Equipment. For further details, contact IMC

Networks. Class 1 Laser product, Luokan 1 Laserlaite,

Laser Klasse 1, Appareil A’Laser de Classe 1

Choose a location that is near the devices to be connected and close to an

electrical outlet. Place the AccessLinX unit on a desktop or other level sur-

face. You may also mount the unit on the wall, using two screws 6.1" (15.5

cm) apart for horizontal positioning or 2.68" (6.8 cm) apart for vertical posi-

tioning. Holes for mounting on the wall are situated at the bottom of the unit.

Connect the network to the LAN4 Uplink port via the 100Base-FX fiber

SFP or the RJ-45 LAN 100BASE-TX connector. Connect any required PC to

the unit using a straight or cross cable. Connect the phones to the

AccessLinX unit via the RJ-11 connectors.

Connect the power adapter to the power connector of the unit and to the

power source. Fasten the DC power-feed cable to the clasp at the bottom of

the unit to avoid accidental disconnection.

NOTE: Be sure to use only the IMC Networks power adapter that was

delivered with the unit.

Verify that all system components are properly installed. Make sure that all

cable connectors are securely positioned in the appropriate ports. Do not

place any object on top of the unit. Make sure that the ventilation holes on

top of the unit are not blocked.

The unit is now ready for configuration. Please refer to the User Guide

located on the User Documentation CD-ROM delivered with the AccessLinX.

LED Operation

AccessLinX has four status LEDs and four Link/Activity LEDs. The LED

functions are as follows:

LED Mode H.323, MGCP, SIP Status Downloader Status

Power Steady glow Power OK Power OK

Ready Blinking Application OK Loader OK

Voice Steady glow Gateway registered with Gatekeeper/

Call Agent / SIP Server

Mngt Blinking Management or voice activity Management activity

LED Mode Status

Link/

Act

Steady glow

Blinking

Indicates Link

Iindicates Activity

NOTE

Connect up to five phones in parallel to each port.