imex A81105A User manual

Smart Push Button
Wall Hung Cistern Frame
Item No.：A81105A
T uch

PARTS LIST
rubber seal straight flush pipe flush pipe eccentric pipe full flush
air hose
rubber seal
half flush
air hose
white
blue
flush pipe rubber seal on
left pipe
expansion nut screw
φ6-8mm
expansion nut
X1 X1 X1 X1X1 X1
X1 X1 X1 X2 X2
X1
X2 X2X2 X2 X2 X2
X2 X2X2 X2 X2
screw washer M12 bolt decorative cap M12 nut
big washer rubber sleeve decorative
cap base
washer
toilet mat
φ22X2mm
φ11X1.2mm
Content
Parts List ---------------------------------------------------------------------------------- 01
Technical Drawing, Inlet System & Drainage System ------------------------------------ 02
Installation Instruction --------------------------------------------------------------------- 03
Maintenance & Daily Care ------------------------------------------------------------------ 08
steel expansion
bolt
01
φ110mm
φ60mm 8X40mm ST4.8X45mm
ST6.8X67mm
φ32.5X2.5mm

glass panel flush valve inlet valve
TECHNICAL DRAWING, INLET SYSTEM & DRAINAGE SYSTEM
screw set cistern bodylever
aluminum frame
push button
half frame drainage eccentric pipe
02
Unit:mm

Step 3
Step 1 Step 2
a: Lean the whole cistern to the wall and align
the flush pipe position with the buckle.
Insert the drainage pipe into the drainage hole on
the wall.
Remove the upper cover, pull up the braid tube until it gets o the
hanger.
c: Move o cistern first.
INSTALLATION INSTRUCTION
b: As indicated by the arrows, mark the 4
spots on the wall and 2 spots on the ground
accordingly.
d: Drill the holes according to the marked
spots (the depth of the drill must be
larger than the length of the expansion
nut, the diameter shown as in the
picture) and press the corresponding
expansion nut into the hole.
a b
cd
hanger on the
back template
03

Step 5
e: Lean the whole frame onto the right
position of the wall.
Install the glass onto the aluminum frame and
push downward the glass support buckle until
the buckles lock with pendant on the aluminum
frame.
f: Look the corresponding size of the screws
into the expansion nut in the wall and steel
expansion bolt on the floor.
Step 4
ef
a: Buckle the braid tube onto the hanger
again, and connect the tube to the angle
valve on the wall.
b: Open the stop valve on the hose to see
whether it is in good condition.
a b
glass support buckle
stuck on the glass(4ps)
04

Step6
a: Install the push button frame
and button onto the glass.
Step 9
Step 7 Step 8
Connect air hoses to the correct positions. Assemble the top cover back to the cistern frame.
a: Draw line on the straight flush pipe
and drain pipe.
b: Insert the two plugs into the positions
as shown.
push button
frame
push button
ab
blue air hose
white air hose
half flush mark
full flush mark
frontage of
the top cover
align line
The rear of the top cover closely cling to
the wall and the frontage is closely cling
to the toilet mat , notice the left and right
should align to the align line shown above.
Final status: The elastic clips
need to buckle the fixed plug.
The elastic clips
on the cover
The fixed plug
on the side plate
a
05

a: Screw the bolts into the cistern frame.
Step 10
b: Cut the flush pipe and drainage pipe.
b
c d
c: Apply chamfer on the mouth of the
flush pipe and drain pipe.
d: Apply silicone oil.
a
b
b: Install toilet mat.
06

e: Install toilet.
c d
ef
c: Install the flush pipe onto the cistern.
d: Install the flush pipe onto the toilet.
f: Cut o extra part of the toilet mat.
g
g: Test half & full flush functions.
07
Note: Toilet installation is for reference only.
Actual installation should follow the toilet
and its instruction.

Step 1
MAINTENANCE & DAILY CARE
Inlet valve removal
a b
c d
a: Remove the top cover.
b: Turn o the stop valve on the flexible
hose.
c: Unconnect hose and the valve.
d: Take o the inlet valve upwards.
08

Step 2
Step 3
Inlet valve adjustment & clean a
b c
a: Adjust the float upwards to increase the inlet volume;
or downwards to reduce the volume.
b: Remove the water-stopping part.
c: Wash this removed part.
Inlet valve installation
09

Step 4
Flush valve removal
a: Un-connect the air hoses from the air
hose holes .
blue air hose
white air hose
ab
b: Remove the lever.
c
buckles on the cistern hunger
c: Lift upwards the flush valve after opening
the buckles on the cistern hunger.
10

Step 5
Flush valve adjustment & clean a
float
a: Adjust the float upwards to reduce the flush
volume; or downwards to increase the volume .
cover
rubber seal
washer
cover
b
c
b: Remove the cover, washer and rubber seal by
rotating counterclockwisely the cover around 90°.
c: Clean the washer.
11

For any further information please contact
IMEX UK on: 01530-835 598
Or visit our web-site at: www.imexceramic.co.uk
Step 6
The manufacturer reserves the right to make technical
modifications without prior notice.
Flush valve installation
flush valve base
“click”
a
bc
d
a: Install the flush valve downwards into the
cistern body ( Mark：make sure the flush
valve bottom is aligned with flush valve
base. And please make sure flush valve is
installed in the shown direction during
installation. )
b: Press the flush valve until it clicks in the
correct position.
c: Re-install the lever.
d: Re-install the top glass cover.
12