Impex Circuit Fitness AMZ-986RW User manual

NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
AMZ-986RW
Retain This
Manual for
Reference
180910
ASSEMBLY &
OWNER'S
MANUAL
Magnetic-Resistance
Deluxe Rowing Machine
AMZ-986RW
IMPEX®INC.
2801 S. Towne Ave, Pomona, CA 91766
Tel: [phone] Fax: [phone]
www.marcypro.com
[email protected]

© IMPEX INC. www.marcypro.com
1
TABLE OF CONTENTS
BEFORE YOU BEGIN
Thank you for selecting the CIRCUIT FITNESS Magnetic-Resistance Deluxe Rowing
Machine AMZ-986RW by IMPEX®INC. For your safety and benefit, read this manual
carefully before using the bike. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are missing
or damaged parts, we guarantee you complete satisfaction through direct assistance
from our factory. To avoid unnecessary delays, please call our TOLL-FREE customer
service number. Our Customer Service Agents will provide immediate assistance to
you.
BEFORE YOU BEGIN
1
IMPORTANT SAFETY NOTICES
2
WARNING LABEL PLACEMENT
3
HARDWARE PACK
4
COMPONENT FOR ASSEMBLY
5
IMPORTANT ASSEMBLY INSTRUCTION
6
EXPLODED DIAGRAM
10
PARTS LIST
12
CARE AND MAINTENANCE, WEIGHT CAPACITY & DIMS.
14
COMPUTER
15
EXERCISE GUIDELINES
17
WARRANTY
19
ORDERING PARTS
19
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.marcypro.com
[email protected]

© IMPEX INC. www.marcypro.com
2
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm
up.
11. Never operate the machine if the machine is not functioning properly.
12. Read all warnings posted on the exercise bike.
13. Inspect the exercise bike for worn or loose component prior to use. Tighten/replace any
loose or wore components prior to use.
14. Care should be taken in mounting or dismounting the exercise bike.
15. This exercise bike is for consumer and home use only.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.

© IMPEX INC. www.marcypro.com
3
WARNING LABEL PLACEMENT
The Warning Labels shown here has been placed on the Front Stabilizer.
If the labels are missing or illegible, please call customer service at 1-800-999-8899 for
replacement. Apply the labels in location shown.

© IMPEX INC. www.marcypro.com
4
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
NO.
Description
QTY
Drawings
3
Flat washer
11
11
Allen Bolt
12
14
End cap for slide rail L/R
1/1
16
Collar
2
17
Allen Bolt M8x ¾”
4
24
Allen Bolt M8x1⅝”
2
27
Stopper
2
32
Allen Bolt M6x½”
4
33
Flat washer
4
34
Axle for pedal
2
35
Acorn nut M8
2
36
Carriage bolt M8*1¾
2
10
Curve washer
5
67
Lock Washer
2
68
Flat washer
2
69
Axle for slide rail
1
8
Knob
1

© IMPEX INC. www.marcypro.com
5
Allen Wrench
1
Allen Key 4MM
2
Allen Key 6MM
2
COMPONENTS FOR ASSEMBLY
NO:5NO:26 NO:23 NO:31L/R
NO:15 NO:2 NO:9 NO:37NO:28

© IMPEX INC. www.marcypro.com
6
ASSEMBLY INSTRUCTION
•Tools Required For Assembling the Machine: One Crossing Wrench and Allen Wrench,
provided by manufacturer.
•NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP 1
⚫Insert Sensor wire (7) and computer wire (74) through the front post (51), then insert front post
(51) into to Main frame (5), Secure from the front side with 1 sets of Allen bolt (11) & curved
washer (10) and from the side with 2 sets of Allen bolts (11) and flat washers (3).
⚫Connect Sensor wire (7) with computer (9). Secure with 4 Screws (6).
⚫Attach the front stabilizer (2) to the main frame (5). Secure using four Allen bolts (11), Four
curve washers (10).
5
210
11
66
9
11
11
11
3
3
10 7
51
74

© IMPEX INC. www.marcypro.com
7
STEP 2.
⚫Attach middle stabilizer (28) to main frame (5), secure with 4 sets of Allen bolts (11) and flat
washers (3).
⚫Attach the left pedal (31L) to the left bracket of the pedal support tube (37), secure using one
axle for pedal (34), two Allen bolts (32) and two flat washers (33). Repeat the same procedure
for right pedal (31R).
⚫Attach the pedal support tube (37) to bottom of the main frame (5). Secure using two carriage
bolts (36), two flat washers (3) and two acorn nuts (35).
5
32
32
32
32
33
33
33 33
34 34
35 3
36
31L 31R
28
11
3
3
11

© IMPEX INC. www.marcypro.com
8
STEP 3
⚫Attach the slide rail (15) to the main frame (5). Secure using one axle for slide rail (69), two
Allen bolts (17), two spring washers (67), and two flat washers (68)
⚫Fold the slide rail (15) Then insert the knob (8).
⚫Slide the seat (23) onto the slide rail (15). Attach two collars (16) to the back of the slide rail
(15) and securing with two Allen bolts (17).
⚫Attach the end caps (14L & 14R) to the back of the slide rail (15).
⚫Attach the Rear stabilizer (26) to back of the slide rail (15). Secure two Allen bolts (24) and two
flat washers (3), one Allen bolt (11) and one flat washer (3).
⚫Attach two stoppers (27) to rear stabilizer (26).
23
14R 14L
16 16
17 17
24 3
311
26
5
15
17
67
68
69
8
17
67 68
27
27

© IMPEX INC. www.marcypro.com
9
STEP 4
⚫Pull out the knob (8) from the main frame and unfold the slide rail (15).
8
STEP 5
⚫Make rear stabilizer to the floor, Insert knob (8) into fixation holes.
8

© IMPEX INC. www.marcypro.com
10
EXPLODED DIAGRAM

© IMPEX INC. www.marcypro.com
11
EXPLODED DIAGRAM
41 43
4042
59
44
2929
48
2929
38L
38R
39
39
40
41
42
45 45
18 18
46 46
47 48
52
29
53 2954 55 56
56 57
58
18
18
33
3
3
60
6060
6160
61
61
61
62
62
63
63
6465
18
66R
66L
29
48
70
32
71
73
50
7
49 72
29
75

© IMPEX INC. www.marcypro.com
12
AMZ-986RW PARTS LIST
NO.
Description
Qty
1L/R
End cap for front stabilizer L/R
1/1
2
Front stabilizer
1
3
Flat washer Ф8*Ф11/16
21
4
Allen bolt M6x¾”
4
5
Main frame
1
6
Screw M5x ½”
4
7
Sensor wire
1
8
Knob
1
9
Computer
1
10
Curve washer Ф8*Ф¾
5
11
Allen Bolt M8x⅝”
12
12
End cap
2
13
Sleeve
2
14L/R
End cap for slide rail L/R
2/2
15
Slide rail
1
16
Collar
4
17
Allen Bolt M8x¾”
6
18
Nylon nut M8
13
19
Axle for Wheel
6
20
Wheel
6
21
Screw M5*9/16
6
22
Seat support plate
1
23
Seat
1
24
Allen bolt M8x1 9/16
2
25
End cap for slide rail
1
26
Rear stabilizer
1
27
Stopper
2
28
Middle stabilizer
1
29
Self-tapping screw ST5*15
12
30
End cap for middle stabilizer
1
31
Pedal L/R
1/1
32
Allen bolt M6x½”
6
33
Flat Washer Ф6*Ф17
4
34
Axle for Pedal
2
35
Scorn nut M8
2
36
Carriage bolt M8x1¾”
2
、

© IMPEX INC. www.marcypro.com
13
NO.
Description
Qty
37
Pedal support tube
1
38L/R
Chain cover L/R
1/1
39
Flange nut
2
40
Screw for clip
2
41
Clip
2
42
Aircraft nut
2
43
Flywheel
1
44
Rope pulley w/rope
1
45
End cap for rope pulley
2
46
Bracket for spring clutch
2
47
Sensor bracket
1
48
Self-tapping screw ST15*9/16
10
49
Spring
1
50
Belt
1
51
Front post
1
52
Decorative cover
1
53
Fix rubber pad
1
54
Upper cover for handlebar
1
55
Handlebar
1
56
End cap for handlebar
2
57
Foam grip for handlebar
2
58
Lower cover for handlebar
1
59
Self-tapping screw 5*9/16
2
60
Powder bushing
4
61
Bearing
4
62
Wheel
2
63
Axle for wheel
2
64
Allen bolt M8x2 3/16”
1
65
Magnetic assembly
1
66L/R
Decorative cover L/R
1/1
67
Lock washer Ф8
2
68
Flat Washer Ф8*Ф1
2
69
Axle for slide rail
1
70
8-level tension gear
1
71
Hex nut M6
2
72
Tension wire
1
73
Hex bolt M6x1”
1
74
Computer wire
1

© IMPEX INC. www.marcypro.com
14
CARE, MAINTENANCE AND STORAGE
1. Inspect and tighten all parts each time you use the machine. Replace any worn parts
immediately.
2. This machine can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use
solvents.
3. Store the rower IN-DOOR. Excess moisture and water would cause rust on the frame.
4. The rower shall be placed at least 24 inches away from the wall or/and any other object such
as furniture to provide safe access to and passage around the machine.
5. To avoid possible injury, the help of two or more people are needed when moving the machine
around.
6. Disposal Instructions –The equipment can be safely disassembled and disposed without
unreasonable hazards. Call your local recycle agency regarding details of recycling.
7. The maximum user weight is 300 lbs.
8. Assembled Dimension (L x W x H): 91”x20.5”x31.5”
9. Folded Dimension (L x W x H): 49”x20.5”x51”
OPERATING NOTES
TRANSPORT
The Rower has a pair of roller wheels on Front Stabilizer End Cap.
To move, fold up the Rower; carefully hold and tilt the Rower, and then roll.

© IMPEX INC. www.marcypro.com
15
COMPUTER
【FUNCTION BUTTONS】
UP▲/ DOWN▼：To press these two buttons through available selection.
To adjust the function value upward and downward.
ENTER: To confirm your selection.
During training, press the button to scan each display function.
START / STOP：To start and stop your selected workout program.
RESET：To reset the computer back to the main menu.
RECOVERY：To activate the RECOVERY PROGRAM that will automatically evaluate your fitness immediately after
your work out.
【DISPLAY FUNCTIONS】
TIME：Preset target time by pressing UP and DOWN buttons (1min ~ 99 min),
increase or decrease setting is 1 minute.
TIME/500M：Your average 500 meter time will automatically be displayed and continuously updated.
SPM：Strokes per minute.
DISTANCE：Preset target value by pressing UP and DOWN buttons ( 0 ~ 99900meters),
increase or decrease setting is 100 meters.
STROKES：Preset target value by pressing UP and DOWN buttons (0~9990 strokes).
increase or decrease setting is 10.
TOTAL STROKES：Accumulates total strokes from 0 up to 9999.
CALORIES：Preset target CALORIES by pressing UP or DOWN buttons (5Cal ~9990Cal),
increase or decrease setting is 5Cal.
PULSE：To preset target value by pressing up/down/mode from 30 to 240, each increase/decrease setting is 1.
The monitor will display user’s heart rate during training. The pulse measurement function is only
used by chest belt system;
CALENDAR：The monitor will display year, month, and day when monitor is in sleep mode.
TEMPERATURE：The monitor will display current room temperature when the monitor is in sleep mode.
CLOCK：The monitor will display current clock when the monitor is in sleep mode.

© IMPEX INC. www.marcypro.com
16
【OPERATION】
1. Install two (2) AA batteries →one long beep for 2 seconds →in the meanwhile, segment test for 2 seconds (Fig.1).
Then, the monitor enters into the CLOCK & CALENDAR MODE. (Fig.2).
2. First, you may enter into the CLOCK field to set YEAR (in the area of STROKES); MONTH (in the area of
CALORIES); DAY (in the area of PULSE). After you confirm it, the ALARM will beep. Press UP KEY to set the
ON/OFF which is the sign of the ALARM. If the sign doesn’t display, you can press ENTER button to jump to the
next one. When the sign of ALARM display “ON”, you can press the ENTER button to set the time of the ALARM
(the same way of the CLOCK setting). After the setting, you shown the picture of the SPORT (Fig.3).
Fig.1 Fig.2
Fig.3 Fig.4
3. When you enter into the picture of the SPORT, the MANUAL & RACE will blink to be selected.
Press UP or DOWN to select it, then press ENTER and confirm all you have selected.
(1) MANUAL(Fig.4):
A. Enter into the MANUAL mode, press UP to set the flickering figure of the TIME. Press ENTER to confirm
it. Then, you can press UP to set DISTANCE→STROKES→CALORIES→PULSE→TIME immediately.(If
you have set the target value for Time then DISTANCE can’t be set, vice versa.)
B. Press START KEY to START, the STOP icon will disappear. Press UP or DOWN to select functions.
C. When the function you have selected count backwards to ZERO or you have pressed the STOP KEY, the
monitor will STOP and display the average figure.
(2) RACE (Fig.5)：
A. Enter into the RACE mode and L1 will glitter, the TIME/500M may display with 8:00.Then, you can press
UP or DOWN to set L1 ~ L15 immediately, press ENTER to confirm. Where after, you can set the
distance of the race(500M~10000M)while the figure of the DISTANCE is blinking.
Press ENTER and the picture of the race will display clearly on the screen.
The figure of the TIME/500M are as follows：
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
L11
L12
L13
L14
L15
8:00
7:30
7:00
6:30
6:00
5:30
5:00
4:30
4:00
3:30
3:00
2:30
2:00
1:30
1:00
Fig.5 Fig.6

© IMPEX INC. www.marcypro.com
17
B. Press START KEY to START and STOP will disappear. The USER & PC will display in the
matrix.(Fig.6).the monitor will STOP when one have reached the distance of race which has been set
before, then the matrix displays “PC WIN or USER WIN”(Fig.7) and may display the state of the energy
after 6 seconds.
Fig.7
C. When the race is over, you can press the START to have a race once again. Press RESET to leave the
picture of the race.
(3) RECOVERY：
After exercising for a period of time, keep wearing chest strap and press “RECOVERY”
button. All function display will stop except “TIME” starts counting down from 00:60 to 00:00.
Screen will display your heart rate recovery status with the F1,F2….to F6. F1 is the best, F6 is the
worst. User may keep exercising to improve the heart rate recovery status.
(Press the RECOVERY button again to return the main display.)
(4) H.R.C:
A. Enter into the MANUAL mode and press “ENTER” button until the figure of the PULSE is blinking .
B. Press “UP”and “DOWN”button to set exercise pulse. The setting values of 30-240.
C. The consumer computer alarm and the figure of the PULSE is blinking when heart rate is above the SET
value.
EXERCISE GUIDELINES
Using your MAGNETIC ROWER will provide you with several benefits, it will improve your physical
fitness, tone muscle and in conjunction with calorie controlled diet help you lose weight.
1. The Warm Up Phase
This stage helps get the blood flowing around the body and the muscles working properly. It will
also reduce the risk of cramp and muscle injury. It is advisable to do a few stretching exercises as
shown below. Each stretch should be held for approximately 30 seconds, do not force or jerk your
muscles into a stretch - if it hurts, STOP.
SIDE BENDS OUTER THIGH
INNER THIGH
FORWARD
BENDS
CALF / ACHILLES

© IMPEX INC. www.marcypro.com
18
2. The Exercise Phase
This is the stage where you put the effort in. After regular use, the muscles in your legs will
become more flexible. Work to your targeted heart rate but it is very important to maintain a
steady tempo throughout. The rate of work should be sufficient to raise your heartbeat into the
target zone shown on the graph below.
This stage should last for a minimum of 12 minutes though most people start at about 15-20
minutes
3. The Cool Down Phase
This stage is to let your Cardio-vascular System and muscles wind down. This is a repeat of the
warm up exercise e.g. reduce your tempo, continue for approximately 5 minutes. The stretching
exercises should now be repeated, again remembering not to force or jerk your muscles into the
stretch.
As you get fitter you may need to train longer and harder. It is advisable to train at least three times
a week, and if possible space your workouts evenly throughout the week.
MUSCLE TONING
To tone muscle while on your MAGNETIC BIKE you will need to have the resistance set quite
high. This will put more strain on our leg muscles and may mean you cannot train for as long as
you would like. If you are also trying to improve your fitness you need to alter your training
program. You should train as normal during the warm up and cool down phases, but towards the
end of the exercise phase you should increase resistance making your legs work harder. You will
have to reduce your speed to keep your heart rate in the target zone.
WEIGHT LOSS
The important factor here is the amount of effort you put in. The harder and longer you work
the more calories you will burn. Effectively this is the same as if you were training to
improve your fitness, the difference is the goal.

© IMPEX INC. www.marcypro.com
19
IMPEX®INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal use
and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only
to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service
Department at 1-800-999-8899. All freights for products return to IMPEX must be prepaid by the customer. This
warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse,
misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by
IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or other damages with respect to any economic loss, loss of property, loss of
revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or
whatsoever natures. Some states do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state. Register
on-line www.marcypro.com
IMPEX®INC.
2801 S. Towne Ave.
Pomona, CA 91766
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899 during our
regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
[email protected]
When ordering replacement part, always give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase