Impex MARCY MCB-347 User manual

MARCY CLASSIC
MCB-347 COMBO BENCH
IMPEX®INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: [phone] Fax [phone]
www.impex-fitness.com
[email protected]
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MCB-347
Retain This
Manual for
Reference
06-25-08
OWNER'S
MANUAL

TABLE OF CONTENTS
BEFORE YOU BEGIN...............................................................................................
1
IMPORTANT SAFETY NOTICE................................................................................
2
HARDWARE PACK……............................................................................................
4
ASSEMBLY INSTRUCTIONS....................................................................................
5
EXPLODED DIAGRAM..............................................................................................
10
PARTS LIST..........................................................................................................….
11
WARRANTY..........................................................................................................….
12
ORDERING PARTS...............................................................................................….
12
BEFORE YOU BEGIN
Thank you for selecting the MARCY CLASSIC MCB-347 COMBO BENCH
by IMPEX®INC. For your safety and benefit, read this manual carefully
before using the machine. As a manufacturer, we are committed to
provide you complete customer satisfaction. If you have any questions,
or find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance
to you.

1
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user weight: 300 lbs.
14. Maximum weight capacity on the uprights: 200 lbs.
16. Maximum weight capacity on the leg developer: 100 lbs.
17. Maximum weight capacity on the lat bar: 100 lbs.
CARE AND MAINTENANCE
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]

1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF
35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED
BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS. 2

WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Cross Brace. If the label is
missing or illegible, please call customer service at 1-800-999-8899 for replacement.
Apply the label in location shown. 3

HARDWARE PACK
4

ASSEMBLY INSTRUCTION
Tools required assembling the machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (SEE DIAGRAM 1)
A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the Mid-span.
Secure each end of Cross Brace with two M10 x 3 1/8” Hex Bolts (#40), four ∅¾”
Washers (#48), one Bracket (#17), and two M10 Aircraft Nuts (#51).
B.) Insert the Backrest Adjustment Bar (#9) through a selected hole to obtain desired incline
of Backrest.
C.) Insert Left & Right Bar Catches (#11) & (#12) into the selected holes on the Rear Upright
Beams to obtain the desired height to hold the weight bar. DIAGRAM 1
5

STEP 2 (SEE DIAGRAM 2)
A.) Attach the Front Stabilizer (#5) to the Main Seat Support (#3). Secure it with two M10 x ¾”
Hex Bolts (#43), four ∅¾” Washers (#48), and two M10 Aircraft Nuts (#51). DO NOT
tighten the nuts and bolts yet.
B.) Attach theMain Seat Support (#3) to the Cross Brace (#2). Secure it with two M10 x 2 1/8”
Hex Bolts (#41), one Bracket (#17), four ∅¾” Washers (#48), and two M10 Aircraft Nuts
(#51).
C.) Attach one end of Diagonal Support (#4) to the Main Seat Support. Secure it with one M8
x 2 1/8” Hex Bolt (#44), two ∅5/8” Washers (#49), and one M8 Aircraft Nut (#52). Attach
the other end to the Front Stabilizer. Secure it with one M8 x ¾” HexBolt (#45) and ∅5/8”
Washer (#49).
D.) Securely tighten all nuts and bolts previously installed.
DIAGRAM 2
6

STEP 3 (SEE DIAGRAM 3)
A.) Attach the Leg Developer (#6) to the bracket on the Front Stabilizer (#5). Secure it with
one M10 x 2 ¾”HexBolt (#42), two Ø ¾” Washers (#48), and one M10 Aircraft Nut (#51).
Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel.
B.) Insert two Foam Tubes (#8) halfway through the holes on the Leg Developer. Push four
Foam Rolls (#39) onto the Tubes from both ends.
C.) Attach the Arm Curl Handle (#7) to the open bracket on the Leg Developer. Use a
L-shaped Lock Pin (#23) to secure the Arm Curl Handle.
D.) Attach a Spring Clip (#21) onto the weight post on the Leg Developer.
DIAGRAM 3
7

STEP 4 (SEE DIAGRAM 4)
A.) Attach the side holes on the Backrest Supports (#14) to the Pivot on the Main Seat
Support (#3). Place the other end rest against the Backrest Adjustment Bar (#9).
B.) Attach theBackrest Board (#19)onto the Backrest Supports. Secure it with four M6 x 1 ½”
Hex Bolts (#47) and ∅½” Washers (#50).
C.) Place the Seat Pad (#18) onto the bracket on the Main Seat Support. Secure it with four
M6 x 1 ¼” Hex Bolts (#46) and ∅½” Washers (#50).
D.) Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#10). Secure it with two M8 x 5/8”
Hex Bolts (#45) and two Ø 5/8” Washers (#49).
E.) Insert the Arm Curl Stand into the opening on the top of the Front Stabilizer. Use a Lock
Knob (#24) to hold it in position. Remove Arm Curl Handle when doing Leg Developer
exercises. DIAGRAM 4