Impex MD-7502 User manual

MARCY DIAMOND
WEIGHT BENCH
MD-7502
IMPEX®INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: [phone] Fax [phone]
www.impex-fitness.com
[email protected]
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MD-7502
Retain This
Manual for
Reference
100924
OWNER'S
MANUAL

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK………............................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 5
EXPLODED DIAGRAM.................................................................................... 10
PARTS LIST..................................................................................................... 11
WARRANTY..................................................................................................... 12
ORDERING PARTS.......................................................................................... 12
BEFORE YOU BEGIN
Thank you for selecting the MARCY DIAMOND WEIGHT BENCH MD-7502 by
IMPEX®INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee your complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. This machine is designed and intended for home and consumer use only, not for
commercial use.
14. Maximum user’s weight: 300 lbs.
15. Maximum weight on uprights: 300 lbs.
16. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
3. Assembled Dimension: 64” x 54” x 40”
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE
OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL PLACEMENT
The Warning Labels shown here have been placed on the Cross Brace. If the label is
missing or illegible, please call customer service at 1-800-999-8899 for replacement.
Apply the label in location shown
3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4

ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended for two or more people to assemble this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Connect the Left & Right Upright Beams (#1 & #2) by a Cross Brace (#3) in the mid-
span. Secure each end of the Cross Brace to each Upright Beam with two M10 x 3 ¾”
Carriage Bolts (#33), one 5 ½” Curved Bracket (#16), two Ø ¾” Washers (#40), and two
M10 Aircraft Nuts (#42).
C.)Place the Backrest Adjustment Bar (#9) onto the selected slot to obtain the desired
backrest incline. DIAGRAM 1
5

STEP 2 (See Diagram 2)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Main Seat Support (#4) to the Front Post (#5). Secure it with two M10 x 2 3/8”
Carriage Bolts (#35), one 6 ¼” x 5 1/8” Bracket (#17), two Ø ¾” Washers (#40), and two
M10 Aircraft Nuts (#42).
C.) Attach the Main Seat Support to the Cross Brace (#3). Secure it with four M10 x 2 ½”
Carriage Bolts (#34), one 5 ½” x 4 3/8” Bracket (#18), four Ø ¾” Washer (#40), and four
M10 Aircraft Nut (#42).
D.) Securely tighten all Nuts and Bolts in Step-1 and Step-2.
E.) Insert the two Crutches (#8) into the Left & Right Upright Beams (#1 & #2). Thread a M18
x Ø 1” Lock Knob (#8) into each Upright Beam to hold the Crutch at selected height.
DIAGRAM 2
6

STEP 3 (See Diagram 3)
A.) Attach the Leg Developer (#11) to the open bracket on Main Seat Support (#4). Secure it
with an Axle (#25), two M10 x ¾” Allen Bolt (#36), and two Ø ¾” Washers (#40). Do not
over tighten the Bolts. Make sure the Leg Developer is able to swivel.
B.) Insert two Foam Tubes (#12) halfway through the holes on the Leg Developer. Push four
Foam Rolls (#23) onto the Tubes from both ends. Plug four Foam Roll End Caps (#29)
into the ends of Tubes.
C.) Slide an Olympic Sleeve (#27) onto the weight post on Leg Developer. Attach a Ø 2”
Spring Clip (#24) onto the Sleeve. DIAGRAM 3
7

STEP 4 (See Diagram 4)
A.) Attach the Seat Bracket (#6) to the pivot on the Main Seat Support (#4). Attach the holes
on the end of the two Backrest Supports (#7) to the Seat Bracket. Align the holes. Secure
the two Backrest Supports, Seat Bracket together to the pivot with one M12 x 7” Hex Bolt
(#32), two Ø 1” Washers (#41), and one M12 Aircraft Nut (#43). Do not over tighten the
Nuts and Bolts. Make sure the Backrest Supports are able to swivel.
B.) Attach the Backrest Board (#13) to the Backrest Supports. Secure it with four M8 x 1 5/8”
Allen Bolts (#37) and four Ø 5/8” Washers (#39).
C.) Place the Seat Pad (#14) onto the Seat Bracket. Secure it with four M8 x 1 5/8” Allen Bolts
(#37) and four Ø 5/8” Washers (#39). DIAGRAM 4
8

STEP 5 (See Diagram 5)
A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#10). Secure it with two M8 x 5/8”
Allen Bolts (#38) and two Ø 5/8” Washers (#39).
B.) Insert the Arm Curl Stand into the opening on front of Main Seat Support (#4). Use the
M18 x Ø ¾” Lock Knob (#20) to hold the Arm Curl Stand at selected height.
C.)Remove Arm Curl Stand when doing Leg Developer exercises.
DIAGRAM 5
9

10

PARTS LIST
KEY NO. DESCRIPTION QUANTITY
1 Left Upright Beam 1
2 Right Upright Beam 1
3 Cross Brace 1
4 Main Seat Support 1
5 Front Post 1
6 Seat Bracket 1
7 Backrest Support 2
8 Crutch 2
9 Backrest Adjustment Bar 1
10 Arm Curl Stand 1
11 Leg Developer 1
12 Foam Tube 2
13 Backrest Board 1
14 Seat Pad 1
15 Arm Curl Pad 1
16 5 ½” Curved Bracket 2
17 6 ¼” x 5 1/8” Bracket 1
18 5 ½” x 4 3/8” Bracket 1
19 M18 x Ø 1” Lock Knob 2
20 M18 x Ø ¾” Lock Knob 1
21 Ø 3” Sleeve 2
22 3 1/8” x 2 ¾” Sleeve 1
23 Foam Roll 4
24 Ø 2” Spring Clip 1
25 Axle 1
26 Ø 2 3/8” Bushing 2
27 Olympic Sleeve 1
28 Ø 2” End Cap 2
29 Foam Roll End Cap 4
30 1” Square End Cap 2
31 Ø 1” End Cap 2
32 M12 x 7” Hex Bolt 1
33 M10 x 3 ¾” Carriage Bolt 4
34 M10 x 2 ½” Carriage Bolt 4
35 M10 x 2 3/8” Carriage Bolt 2
36 M10 x ¾” Allen Bolt 2
37 M8 x 1 5/8” Allen Bolt 8
38 M8 x 5/8” Allen Bolt 2
39 Ø 5/8” Washer 10
40 Ø ¾” Washer 12
41 Ø 1” Washer 2
42 M10 Aircraft Nut 10
43 M12 Aircraft Nut 1
44 Ø 1” Flat End Cap 1
11

IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal
use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty
extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or
repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. The customer must prepay all freights on products returned to IMPEX.
This warranty does not extend to any product or damage to a product caused by or attributable to freight damage,
abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for
products used for commercial or rental purposes. No other warranty beyond that specifically set forth above is
authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential
damages or whatsoever natures. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
Register on-line www.impex-fitness.com
IMPEX®INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
[email protected]
When ordering replacement parts, always give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase
12