Impex SB 208 User manual

NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
SB 208
Retain This
Manual for
Reference
06-01-01
OWNER'S
MANUAL
WORKOUT BENCH
MARCY SB 208
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[e-mail]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE IDENTIFIER.....…....................................................................... 3
ASSEMBLY INSTRUCTIONS........................................................................... 4
EXPLODED DIAGRAM……………………………………………………………… 6
PARTS LIST...................................................................................................... 7
WARRANTY.................................................................................................…. 8
ORDERING PARTS.......................................................................................… 8
BEFORE YOU BEGIN
Thank you for selecting the MARCY SB-208 Workout Bench by IMPEX FITNESS
PRODUCTS. For your safety and benefit, read this manual carefully before using
the machine. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing or
damaged parts, we guarantee you complete satisfaction through direct assistance
from our factory. To avoid unnecessary delays, please call our TOLL-FREE
customer service number. Our Customer Service Agents will provide immediate
assistance to you.
11
Toll-Free Customer Service Number
1-800-999-8899
Mon. -Fri. 9 a.m. -5 p.m. PST
www.impex-fitness.com
[e-mail]

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply whenever you
operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or
operate your machine. In particular, note the following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS
WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING
ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS
PRODUCT.
SAVE THESE INSTRUCTIONS.
2

3

ASSEMBLY INSTRUCTION
Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended this machine be assembled by two or more people to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Slide the Sliding Block (#9) onto the Main Frame (#2) and secure it with a Quick Release Knob
(#26). Attach the Base Frame (#7) to the Main Frame (#2). Secure it with two M10 x 5/8” Allen
Bolts (#10) and two∅7/8” Washers (#14).
B.) Attach the Base Frame (#7) to the Front Frame (#1). Secure it with two M10 x 5/8” Allen Bolts
(#10), two ∅7/8” Washers (#14).
C.) Attach the Main Frame (#2) to the Front Frame (#1). Secure it with a M10 x 3” Allen Bolt (#11),
two ∅7/8” Washers (#14) and a M10 Aircraft Nut (#17) to the lower hole. NOTE: DONOT over
tighten the bolt. The joint needs to swivel in able to fold thebench for storage. Insert a L-shaped
Lock Pin (#18) to the upper hole.
D.) Attach the Cross Tube (#5) to the Front Frame (#1). Secure it with a M10 Knob Lock (#23).
DIAGRAM 1
4

STEP 2 (See Diagram 2)
A.) Attach theholed-side of the Backrest Support Bars (#4) onto both ends of the Pivot on the
Main Frame (#2).
B.) Attach an Incline Support (#3) to the bracket on the Backrest Support Bar (#4). Secure it with a
M10 x 1 ¾” Allen Bolt (#27), two∅7/8” Washers (#14), and one M10 Aircraft Nut (#17). Repeat the
same procedure to install the other side.
C.)Attach the Incline Supports (#3) to the pivot on the Sliding Block (#9). Align the holes and secure
them with a M10 x 7 7/8” Axle (#25), two∅7/8” Washers (#14), and two M10 Aircraft Nuts (#17).
D.)Attach the Backrest Board (#8) to the Backrest Support Bars (#4). Secure it with four M6 Philips
Head Screws (#12) and∅1/4” Washers (#13).
E.) Insert a Foam Tube (#6) halfway into the hole on the Front Frame (#1). Slide two Foam Rolls (#15)
onto the tube from both sides. Then slide two Foam Grips (#16) onto the tube from both sides.
Slide two Foam Rolls (#15) onto the Cross Tube (#5) from both sides.
DIAGRAM 2
5

6

Parts list
KEY NO. DESCRIPTION Q’ty
1Front Frame 1
2Main Frame 1
3Incline Support 2
4Backrest Support Bar 2
5Cross Tube 1
6Foam Tube 1
7Base Frame 2
8Backrest Board 1
9Sliding Block 1
10 M10 x 5/8” Allen Bolt 4
11 M10 x 3” Allen Bolt 1
12 M6 Philips Head Screw 4
13 ∅¼” Washer 4
14 ∅7/8” Washer 12
15 Foam Roll 4
16 Foam Grip 2
17 M10 Aircraft Nut 5
18 L-shaped Lock Pin 1
19 1” Square End Cap 8
20 ∅1” End Cap 4
21 ∅2 3/8” End Cap 4
22 2” Square End Cap 1
23 M10 Knob Lock 1
24 Sleeve 2
25 M10 x 7 7/8” Axle 1
26 Quick Release Knob 1
27 M10 x 1 ¾” Allen Bolt 2
7

IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must
be prepaid by the customer. This warranty does not extend to any product or damage to a product
caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs
not provided by an IMPEX authorized service center or for products used for commercial or rental
purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to
the terms set forth herein. Some states do not allow limitations on how long an implied warranty
lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-
999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
www.impex-fitness.com
[e-mail]
When ordering replacement parts, always give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase
8