In-situ SludgeWatch 715 User manual

2023-11-01 | 156770
Operator’s Manual
SludgeWatch 715 Portable Sludge
Blanket Detector

2
Information subject to change without notice. In-Situ, In-Situ logo, “Water Simplied”, VuLink, RDO,
RuggedCable, TROLL, BaroTROLL, HydroVu, VuSitu, Baro Merge, and Win-Situ are trademarks or registered
trademarks of In-Situ Inc. ©2023. All rights reserved. This product may be covered by patents identied at
www.in-situ.com/patents.
For a list of local compliance representatives, see www.in-situ.com/us/faq/regulatory-compliance/
compliance-information/global-market-contacts
Your equipment was carefully inspected before shipping. Check the equipment for any physical damage
sustained during shipment. Notify In-Situ and le a claim with the carrier if there is any such damage; do
not attempt to deploy or operate the equipment.
Unpacking and Inspecting
Save packing materials for future storage and shipping of your equipment.
If you have questions or experience problems with your equipment, contact our skilled technical support
team in your area by chat, email, or phone by going to www.in-situ.com/support.
Be sure to have the following information available:
• Product model
• Serial number
• Description of the problem, including how the product was used and the conditions noted at the time
of the malfunction
Technical Support
Document Conventions
Throughout this document, you will see the following symbols:
A checkmark highlights a tip or feature.
The exclamation point calls your attention to a requirement, safety issue, or important
action that should not be overlooked.
www.in-situ.com

3
Contents
Technical Support...................................................................................................................................... 2
Unpacking and Inspecting ...................................................................................................................................................2
Document Conventions ............................................................................................................................ 2
Introduction............................................................................................................................................... 4
Instrument Description..........................................................................................................................................................4
Instrument Details ...................................................................................................................................................................4
Instrument Parts.......................................................................................................................................................................5
Getting Started.......................................................................................................................................... 9
Box Contents..............................................................................................................................................................................9
Safety .......................................................................................................................................................11
Intended Use .......................................................................................................................................................................... 11
Technical Specications.......................................................................................................................... 12
General Specications......................................................................................................................................................... 12
Sensor Specications........................................................................................................................................................... 12
Serial Number & Part Numbers ..............................................................................................................13
Serial Number & Part Number Location........................................................................................................................ 13
Sensor Type & Part Number .............................................................................................................................................. 13
Declarations of Similarity .......................................................................................................................14
www.in-situ.com

4
Introduction
The SludgeWatch 715 Portable Sludge Blanket Detector is designed for spot-checking sludge interface
levels in settling tanks.
Instrument Description
The SludgeWatch’s sensor lowers into a settling
tank to detect the sludge blanket at the bottom of
the tank.
It works by measuring the change in the level of suspended solids as the sensor is lowered into the tank.
When the sensor reaches the sludge blanket, the audible signal changes from a fast beep to a slow beep.
A red LED light visually indicates that the sludge blanket has been detected.
The sensor’s cable is marked in either 1.0 m or 3.0 ft intervals to measure the sludge interface position.
The 715 consists of three main parts:
Instrument Details
• the cable reel unit (which houses the detector’s electronics and battery, and is also used to store the
cable when not in use)
• the cable itself
• the IR sensor (attached to the bottom of the cable)
The sensor is available as an IR8, IR15, IR40, or IR100 sensor as required for the application.
The IR sensor uses light absorption across a single measurement gap to determine the total suspended
solids in a solution. The length of the sensing gap determines the measurement range of the sensor.
www.in-situ.com

5
6
4
2
3
1
5
1. Sensor
2. On/o switch
3. Cable reel handle
4. Cable
5. LED light
6. Battery compartment
Instrument Parts
www.in-situ.com

Getting Started
Box Contents
• SludgeWatch 715 Portable Sludge Blanket Detector
• 9 V alkaline battery
Conduct operation test before each use.
1
Insert battery. Move
power switch to “on.”
Ensure sensor gap is
clear. Listen for fast
beeps.
If test is successful,
continue. If test fails,
replace battery. Ensure
sensor gap is clear.
Check sensor. Block
the gap. Listen for slow
beeps. Identify bright
LED light.
Measure the sludge blanket.2
Always keep the cable taut and reel slowly. Fast reeling can cause jamming.
Use the cable reel
handle to slowly lower
the sensor into settling
tank.
When the beep changes
from fast to slow and
when the LED light
ashes red, the sensor
has reached the sludge
blanket.
Switch unit o. Reel the
cable in slowly, keeping
it taut the entire time.
Record the sludge
blanket’s depth by
noting the highest
numerical measurement
on the cable.
2.0 m
2023-11-01 | 156770IM-Iss08
SludgeWatch 715 Portable Sludge
Blanket Detector
Information subject to change without notice. In-Situ, In-Situ logo, “Water Simplied”, VuLink, RDO, RuggedCable, TROLL,
BaroTROLL, HydroVu, VuSitu, Baro Merge, and Win-Situ are trademarks or registered trademarks of In-Situ Inc. ©2023. All rights
reserved. This product may be covered by patents identied at www.in-situ.com/patents.

10
Use a damp cloth and
mild detergent to clean
the cable.
Clean sensor with a
soft cloth and mild
detergent. Rinse with
clean water.
Learn More
View additional specications, compliance information, and detailed instructions at www.in-situ.com.
Clean cable and sensor.
3
Never fully immerse the entire SludgeWatch unit in liquid.
www.in-situ.com

11
Safety
• Submerge only the cable and sensor in liquid. Do not submerge the entire cable reel unit in liquid.
• Slowly reel the cable or the unit may jam.
• If the cable reel jams inside the housing unit, carefully free the cable by unwinding it.
• Use only mild detergent and clean water to clean the cable and sensor. Do not use harsh chemicals.
• Turn o the unit after use.
Read the safety information on this page before using the SludgeWatch 715 Portable Sludge
Blanket Detector. If you have questions, contact In-Situ Technical Support for assistance.
If the equipment is used in a manner not specied by the manufacturer, the protection
provided for the equipment may be impaired.
Intended Use
The SludgeWatch 715 Portable Sludge Blanket Detector is designed to be safe in these conditions:
• Operable temperatures of 0° to 50° C (32° to 122° F)
www.in-situ.com

Technical Specications
Battery Type 9 V DC (alkaline battery PP3)
Battery Life >200 hours
Operating Temperature Range 0° to 50° C (32° to 122° F)
Storage Temperature Range -20° to +60° C (-4° to +140° F)
Environmental Rating IP65
Cable Type 4 core, polyurethane coated
Standard Cable Length 10 m (32.8 ft)
Maximum Cable Length 15 m (49 ft)
Cable Marking 1.0 m or 3.0 ft
Weight 1.7 kg (3.75 lbs)
Dimensions 280 x 230 x 130 mm (h x w x d)
11 x 9 x 5.1 in (h x w x d)
Measuring Principle Light absorption
Light Source Infrared LED, 950 nm
Protection Class IP68 (Sensor), IP54 (Electronics)
Materials Hastelloy, PVC, Epoxy Potting Compound
Sensor Type Dimensions Range Optical Path Setpoint
IR100 95 x 100 x 25 mm
(3.7 x 3.9 x .9 in) 0-200 mg/l 100 mm 100 mg/l
IR40 95 x 40 x 25 mm
(3.7 x 1.6 x .9 in) 0-1500 mg/l 40 mm 750 mg/l
IR15 95 x 15 x 25 mm
(3.7 x .6 x .9 in) 0-10,000 mg/l 15 mm 5,000 mg/l
IR8 95 x 8 x 25 mm
(3.7 x .3 x .9 in) 0-30,000 mg/l 8 mm 15,000 mg/l
The values below are based on typical solids found in municipal sewage treatment plants.
General Specications
Sensor Specications
12 www.in-situ.com

Serial Number & Part Numbers
13 www.in-situ.com
The instrument’s part number (PN) is on the product label axed to the instrument body. The serial
number (SN) for the SludgeWatch main unit is on the back of the reel. The SN for the sensor is located on
the sensor itself.
Serial Number & Part Number Location
Sensor Type & Part Number
Sensor Type Part Number
SludgeWatch 715 Portable c/w IR100 sensor (1.0 m marking) 107800
SludgeWatch 715 Port able c/w IR40 sensor (1.0 m marking) 230484
SludgeWatch 715 Portable c/w IR15 sensor (1.0 m marking) 107790
SludgeWatch 715 Portable c/w IR8 sensor (1.0 m marking) 141300
SludgeWatch 715 Portable c/w IR100 sensor (3.0 ft marking) 230475
SludgeWatch 715 Portable c/w IR40 sensor (3.0 ft marking) 230473
SludgeWatch 715 Portable c/w IR15 sensor (3.0 ft marking) 230474
SludgeWatch 715 Portable c/w IR8 sensor (3.0 ft marking) 230476

14
Declarations of Similarity
Copyright © 2015 In-Situ Inc. This document is confidential and is the property of In-Situ Inc. Do not distribute without approval.
UKCA Declaration of Similarity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product is similar in performance to the SludgeWatch 715 Portable
with IR40 Sensor:
Product name:
SludgeWatch 715 Portable with IR100 Sensors
Model: SludgeWatch 715 Portable with IR100 Sensors
Part Numbers: 107800, 230475
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with
markings every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket
level in a wide variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is
used primarily at wastewater treatment plants.
is in compliance with the following Regulations:
• EMC Regulation 2016
• Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS) Regulation (S.I. 2012:3032)
and meets or exceeds the following British requirements and compliance standards:
• EMC: BS 61326-1:2021
• RoHS: BS 63000:2018
The UKCA mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
In-Situ, Inc.
July 13, 2022
www.in-situ.com

15
Copyright © 2015 In-Situ Inc. This document is confidential and is the property of In-Situ Inc. Do not distribute without approval.
CE Declaration of Similarity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product is similar in performance to the SludgeWatch 715 Portable
with IR40 Sensor:
Product name: SludgeWatch 715 Portable with IR100 Sensors
Model: SludgeWatch 715 Portable with IR100 Sensors
Part Numbers: 107800, 230475
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with
markings every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket
level in a wide variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is
used primarily at wastewater treatment plants.
is in compliance with the following Directive
• 2014/30/EU EMC Directive
• Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS) Directive, 2011/65/EU and Commission Delegated Directive, (EU)
2015/863
and meets or exceeds the following international requirements and compliance standards:
EMC Standards:
EN 61326-1:2021
RoHS Standard:
EN 63000:2018
The CE mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
In-Situ, Inc.
July 22, 2022
www.in-situ.com

16
Copyright © 2015 In-Situ Inc. This document is confidential and is the property of In-Situ Inc. Do not distribute without approval.
CE Declaration of Similarity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product is similar in performance to the SludgeWatch 715 Portable
with IR40 Sensor:
Product name: SludgeWatch 715 Portable with IR15 Sensors
Model: SludgeWatch 715 Portable with IR15 Sensors
Part Numbers: 107790, 230474
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with
markings every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket
level in a wide variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is
used primarily at wastewater treatment plants.
is in compliance with the following Directive
• 2014/30/EU EMC Directive
• Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS) Directive, 2011/65/EU and Commission Delegated Directive, (EU)
2015/863
and meets or exceeds the following international requirements and compliance standards:
EMC Standards:
EN 61326-1:2021
RoHS Standard:
EN 63000:2018
The CE mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
In-Situ, Inc.
July 22, 2022
www.in-situ.com

17
Copyright © 2015 In-Situ Inc. This document is confidential and is the property of In-Situ Inc. Do not distribute without approval.
UKCA Declaration of Similarity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product is similar in performance to the SludgeWatch 715 Portable
with IR40 Sensor:
Product name: SludgeWatch 715 Portable with IR15 Sensors
Model: SludgeWatch 715 Portable with IR15 Sensors
Part Numbers: 107790, 230474
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with
markings every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket
level in a wide variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is
used primarily at wastewater treatment plants.
is in compliance with the following Regulations:
• EMC Regulation 2016
• Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS) Regulation (S.I. 2012:3032)
and meets or exceeds the following British requirements and compliance standards:
• EMC: BS 61326-1:2021
• RoHS: BS 63000:2018
The UKCA mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
In-Situ, Inc.
July 13, 2022
www.in-situ.com

18
Copyright © 2015 In-Situ Inc. This document is confidential and is the property of In-Situ Inc. Do not distribute without approval.
UKCA Declaration of Conformity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product:
Product name: SludgeWatch 715 Portable with IR40 Sensors
Model: SludgeWatch 715 Portable with IR40 Sensors
Part Numbers: 100610, 230473
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with
markings every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket
level in a wide variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is
used primarily at wastewater treatment plants.
is in compliance with the following Regulations:
• EMC Regulation 2016
• Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS) Regulation (S.I. 2012:3032)
and meets or exceeds the following British requirements and compliance standards:
• EMC: BS 61326-1:2021
• RoHS: BS 63000:2018
The UKCA mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
In-Situ, Inc.
July 13, 2022
www.in-situ.com

19
Partech (Electronics) Ltd, Rockhill Business Park, St Austell, Cornwall PL26 8RA, UK
T: [phone] F: [phone]
E: [e-mail] www.partech.co.uk
Company Reg No: 804340 VAT No: GB 131 7966 58
CE Declaration of Similarity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product is similar in performance to the SludgeWatch
715 Portable with IR40 Sensor:
Product name: SludgeWatch 715 Portable with IR8 Sensors
Model: SludgeWatch 715 Portable with IR8 Sensors
Part Numbers: 141300, 230476
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with markings
every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket level in a wide
variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is used primarily at
wastewater treatment plants.
This product is in compliance with the following Directives
• 2014/30/EU EMC Directive
• Restriction of the use of certain hazardous substances in electrical and electronic equipment
(RoHS) Directive, 2011/65/EU and Commission Delegated Directive, (EU) 2015/863
and meets the following international requirements and compliance standards:
EMC Standards:
EN 61326-1:2021
RoHS Standard:
EN 63000:2018
The CE mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
Partech, Inc.
May 13, 2023
www.in-situ.com

20
Partech (Electronics) Ltd, Rockhill Business Park, St Austell, Cornwall PL26 8RA, UK
T: [phone] F: [phone]
E: [e-mail] www.partech.co.uk
Company Reg No: 804340 VAT No: GB 131 7966 58
CE Declaration of Similarity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product is similar in performance to the SludgeWatch
715 Portable with IR40 Sensor:
Product name: SludgeWatch 715 Portable with IR8 Sensors
Model: SludgeWatch 715 Portable with IR8 Sensors
Part Numbers: 141300, 230476
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with markings
every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket level in a wide
variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is used primarily at
wastewater treatment plants.
This product is in compliance with the following Directives
• 2014/30/EU EMC Directive
• Restriction of the use of certain hazardous substances in electrical and electronic equipment
(RoHS) Directive, 2011/65/EU and Commission Delegated Directive, (EU) 2015/863
and meets the following international requirements and compliance standards:
EMC Standards:
EN 61326-1:2021
RoHS Standard:
EN 63000:2018
The CE mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
Partech, Inc.
May 13, 2023
www.in-situ.com

21
Copyright © 2015 In-Situ Inc. This document is confidential and is the property of In-Situ Inc. Do not distribute without approval.
UKCA Declaration of Similarity
Manufacturer: Partech Electronics Ltd.
St Austell, Cornwall, PL26 8RA, United Kingdom
Declares that the following product is similar in performance to the SludgeWatch 715 Portable
with IR40 Sensor:
Product name: SludgeWatch 715 Portable with IR8 Sensors
Model: SludgeWatch 715 Portable with IR8 Sensors
Part Numbers: 141300, 230476
Model Variants: One model variant has a cable length of 10m/32.8 ft and one has a cable length of 32 ft with
markings every ft.
Product Description: The SludgeWatch 715 provides a simple method of spot checking the sludge blanket
level in a wide variety of settlement tanks. The sensor is attached to a reel making the unit portable. This is
used primarily at wastewater treatment plants.
is in compliance with the following Regulations:
• EMC Regulation 2016
• Restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS) Regulation (S.I. 2012:3032)
and meets or exceeds the following British requirements and compliance standards:
• EMC: BS 61326-1:2021
• RoHS: BS 63000:2018
The UKCA mark is affixed accordingly.
David A. Bossie
Regulatory Compliance Manager
In-Situ, Inc.
July 13, 2022
www.in-situ.com