Inalto ASL60DR2S User manual

USER MANUAL INALTO.HOUSE
MODEL CODE/S
ASL60DR2S / ASL90DR2S
A HIGHER LEVEL OF COOKING
60cm &90cm
Slide-out
Rangehoods
—
V.4  1220

Residentia Group Pty Ltd
ACN. 600 546 656
165 Barkly Avenue
Burnley, Victoria 3121
Australia
—
Applico Ltd
635 Great South Road
Penrose, Auckland 1061
New Zealand
—
InAlto
www.inalto.house
/inalto.house
/inalto.house
Welcome Congratulations on purchasing
your new appliance!
The InAlto brand is proudly distributed within
Australia by Residentia Group Pty Ltd and within
New Zealand by Applico Ltd.
Please refer to the warranty card at the rear of this
manual for information regarding your product’s parts
and labour warranty, or visit online at:
→ www.residentia.group
→ www.applico.co.nz
→ www.inalto.house
Both Residentia Group & Applico are customer obsessed
and our Support Teams are there to ensure you get the
most out of your appliance. Should you want to learn
more about recommended usage, the various features of
your appliance, and importantly taking care of the unit
when cleaning, our Support Teams are here to help.
Telephone Contacts:
→AU: 1300 11 4357
→ NZ: 0800 763 448
It is important that you read through the following use
and care manual thoroughly to familiarise yourself with
the installation and operation requirements of your
appliance to ensure optimum performance.
Again, thank you for choosing an InAlto appliance and
we look forward to being of service to you.

InAlto recommends the use of original spare parts. When contacting our customer
service team on 1300 11 4357, please ensure that you have the following information
at hand (which can be found on your appliances’ rating plate).
• Model Number
• Serial Number
Customer Care
Contents 2 Welcome
4 General Safety
6 Installation Instructions
11 Your InAlto Rangehood
13 Operation Instructions
14 Cleaning & Maintenance
16 Troubleshooting
16 Technical Data
18 Your Receipt
19 Purchase Details
20 Warranty Information

4
General Safety
5
Read this manual thoroughly before first use,
even if you are familiar with this type of product.
The safety precautions enclosed herein reduce
the risk of fire, electric shock and injury when
correctly adhered to. Keep the manual in a
safe place for future reference, along with the
completed warranty card and purchase receipt.
If applicable, pass these instructions on to the
next owner of the appliance. Always follow basic
safety precautions and accident prevention
measures when using an electrical appliance,
including the following:
Important Installation Advice
WARNING: All electrical work associated with the
installation of this rangehood must be carried out
by a licensed electrician.
WARNING: This rangehood must be installed by
a suitably qualified person in strict accordance
with all instructions in this manual.
Cables: Do not allow electrical fittings or cables
to come into contact with areas on the associated
equipment (cooktop or stove) that get hot.
Air discharge: The exhaust air must not be
discharged into a flue which is used for
exhausting fumes from appliances burning gas or
other fuels.
External air evacuation: Make sure to follow your
local laws that apply to external air evacuation
when installing and using the rangehood.
Electrical safety and cord handling
Voltage and frequency: Before plugging the
unit into an appropriate electrical outlet, make
sure your outlet voltage and circuit frequency
correspond to the voltage stated on the
appliance rating label.
Power cord: Check the cord regularly for damage.
Do not use the appliance if the cord, or any other
part of the appliance, has been damaged.
Damaged cord: A damaged cord must be
replaced by the manufacturer or a similarly
qualified person in order to avoid a hazard.
Disconnect: Before cleaning the rangehood,
make sure to switch it off and unplug it from the
electrical supply. Do not disconnect the appliance
with wet hands. Grip by the plug, do not pull by
the cord when disconnecting.
Usage conditions and restrictions
Domestic use only: This rangehood is designed
for indoor domestic use only. It can be built
into a standard kitchen cabinet or housing unit
following the installation instructions in this
manual.
Intended purpose: Only use this rangehood for
its intended purpose, in its intended environment
and as described in this manual. Any other use
may cause fire, electric shock or injury.
Use common sense: These instructions are
not intended to cover every possible condition
and situation. As with any electrical household
appliance, common sense and caution are
therefore always recommended when installing,
operating and maintaining the equipment.
GENERAL SAFETY
6
General Safety Continued
Usage restriction: This rangehood is not intended
for use by persons (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children: Supervise young children to ensure they
do not play with the appliance. Close supervision
is necessary when any appliance is used by or
near children.
No timer: The appliance is not intended to
be operated by means of an external timer or
separate remote control system.
CAUTION: Take care when the rangehood
is operating simultaneously with an open
fireplace or burner that depend on air from the
environment and are supplied by other than
electrical energy, as the rangehood removes air
from the environment which a burner or fireplace
needs for combustion.
Ventilation: The rangehood removes air from
the environment during use. Always provide
adequate ventilation for safe operation of the
rangehood. This is particularly important when
the rangehood is used at the same time as flued
heaters burning gas or other fuels.
CAUTION: No open flame cooking: Do not
use an open flame for cooking underneath this
rangehood. Open flames can damage the filters
and present a fire hazard.
Unattended: Do not leave the rangehood
unattended during use.
After use: Make sure to switch off the rangehood
after use and before cleaning.
CAUTION: Do not touch the light bulbs after
the appliance has been used as they may be
hot. Let them cool down before cleaning and
maintenance.
WARNING: Fire Risk! Clean your rangehood
regularly as instructed in this manual. There
is a fire risk if cleaning is not carried out in
accordance with the instructions.
Cleaning: Do not use steam cleaning equipment
for cleaning any part of the rangehood.
Filters: Do not check the status of the filters while
the rangehood is in use.
Damage: Do not use the rangehood if any part,
including the supply cord, has been damaged,
is faulty or does not work properly. Only have it
repaired by an authorised service centre. Incorrect
repair could expose you to the risk of electric
shock, fire or injury. Prolonged use of the unit in
such conditions could cause fire or electrocution.
In case of damage, contact our after sales support
line for advice.
Liability: We assume no liability for any eventual
damages caused by incorrect installation, misuse
of the product or noncompliance with these
instructions.
WARNING: All electrical work associated with
the installation of this rangehood must be carried
out by a licensed electrician.
WARNING: This rangehood must be installed by
a suitably qualified person in strict accordance
with all instructions in this manual.

5
5
Read this manual thoroughly before first use,
even if you are familiar with this type of product.
The safety precautions enclosed herein reduce
the risk of fire, electric shock and injury when
correctly adhered to. Keep the manual in a
safe place for future reference, along with the
completed warranty card and purchase receipt.
If applicable, pass these instructions on to the
next owner of the appliance. Always follow basic
safety precautions and accident prevention
measures when using an electrical appliance,
including the following:
Important Installation Advice
WARNING: All electrical work associated with the
installation of this rangehood must be carried out
by a licensed electrician.
WARNING: This rangehood must be installed by
a suitably qualified person in strict accordance
with all instructions in this manual.
Cables: Do not allow electrical fittings or cables
to come into contact with areas on the associated
equipment (cooktop or stove) that get hot.
Air discharge: The exhaust air must not be
discharged into a flue which is used for
exhausting fumes from appliances burning gas or
other fuels.
External air evacuation: Make sure to follow your
local laws that apply to external air evacuation
when installing and using the rangehood.
Electrical safety and cord handling
Voltage and frequency: Before plugging the
unit into an appropriate electrical outlet, make
sure your outlet voltage and circuit frequency
correspond to the voltage stated on the
appliance rating label.
Power cord: Check the cord regularly for damage.
Do not use the appliance if the cord, or any other
part of the appliance, has been damaged.
Damaged cord: A damaged cord must be
replaced by the manufacturer or a similarly
qualified person in order to avoid a hazard.
Disconnect: Before cleaning the rangehood,
make sure to switch it off and unplug it from the
electrical supply. Do not disconnect the appliance
with wet hands. Grip by the plug, do not pull by
the cord when disconnecting.
Usage conditions and restrictions
Domestic use only: This rangehood is designed
for indoor domestic use only. It can be built
into a standard kitchen cabinet or housing unit
following the installation instructions in this
manual.
Intended purpose: Only use this rangehood for
its intended purpose, in its intended environment
and as described in this manual. Any other use
may cause fire, electric shock or injury.
Use common sense: These instructions are
not intended to cover every possible condition
and situation. As with any electrical household
appliance, common sense and caution are
therefore always recommended when installing,
operating and maintaining the equipment.
GENERAL SAFETY
6
General Safety Continued
Usage restriction: This rangehood is not intended
for use by persons (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children: Supervise young children to ensure they
do not play with the appliance. Close supervision
is necessary when any appliance is used by or
near children.
No timer: The appliance is not intended to
be operated by means of an external timer or
separate remote control system.
CAUTION: Take care when the rangehood
is operating simultaneously with an open
fireplace or burner that depend on air from the
environment and are supplied by other than
electrical energy, as the rangehood removes air
from the environment which a burner or fireplace
needs for combustion.
Ventilation: The rangehood removes air from
the environment during use. Always provide
adequate ventilation for safe operation of the
rangehood. This is particularly important when
the rangehood is used at the same time as flued
heaters burning gas or other fuels.
CAUTION: No open flame cooking: Do not
use an open flame for cooking underneath this
rangehood. Open flames can damage the filters
and present a fire hazard.
Unattended: Do not leave the rangehood
unattended during use.
After use: Make sure to switch off the rangehood
after use and before cleaning.
CAUTION: Do not touch the light bulbs after
the appliance has been used as they may be
hot. Let them cool down before cleaning and
maintenance.
WARNING: Fire Risk! Clean your rangehood
regularly as instructed in this manual. There
is a fire risk if cleaning is not carried out in
accordance with the instructions.
Cleaning: Do not use steam cleaning equipment
for cleaning any part of the rangehood.
Filters: Do not check the status of the filters while
the rangehood is in use.
Damage: Do not use the rangehood if any part,
including the supply cord, has been damaged,
is faulty or does not work properly. Only have it
repaired by an authorised service centre. Incorrect
repair could expose you to the risk of electric
shock, fire or injury. Prolonged use of the unit in
such conditions could cause fire or electrocution.
In case of damage, contact our after sales support
line for advice.
Liability: We assume no liability for any eventual
damages caused by incorrect installation, misuse
of the product or noncompliance with these
instructions.
CAUTION: Take care when the rangehood is
operating simultaneously with an open fireplace or
burner that depend on air from the environment and
are supplied by other than electrical energy, as the
rangehood removes air from the environment which
a burner or fireplace needs for combustion.
CAUTION: No open flame cooking: Do not
use an open flame for cooking underneath this
rangehood. Open flames can damage the filters
and present a fire hazard.
CAUTION: Do not touch the light bulbs after
the appliance has been used as they may be hot.
Let them cool down before cleaning and
maintenance.
WARNING: Fire Risk!
Clean your rangehood regularly as instructed in this
manual. There is a fire risk if cleaning is not carried
out in accordance with the instructions.

6
Installation Instructions
8
INSTALLATION
Installation Kit
The installation kit contains the following parts:
Part ID Description Illustration Qty
1 Rangehood 1
2Rear-underside support mounting
bracket 1
3 40mm Height Front Fascia Rail 1
4Charcoal Filters
—Already installed
1 set
(2 pcs)
5 Screws (ST4 x 30mm) 6
6 Screws (ST4 x 8mm) 2
7 Wall Plugs (8mm) 6
8 Flat Washers 6
9Front Vent Cover
—If external ducting selected 1
10 Flu Outlet Adapter 1
9
Unpacking
• This product has been packaged to protect
it against transportation damage. Unpack
the appliance and remove all packaging
materials from around the rangehood. Keep
all packaging materials until you have made
sure your new rangehood is undamaged
and in good working order. The carton is
recyclable. Whenever possible, reuse the
carton and recycle it when disposing of
the packaging materials.
• Plastic wrapping can be a suffocation hazard
for babies and young children, so ensure all
packaging materials are out of their reach,
and dispose of them safely.
Important installation advice
WARNING!
• All electrical work associated with the
installation of this rangehood must be carried
out by a licensed electrician.
• This rangehood must be correctly installed by
a suitably qualifi ed person in strict accordance
with all applicable rules and regulations and
following the instructions in this manual.
• Do not try to install the rangehood yourself;
doing so will expose you to danger and void
the warranty. Improper installation, adjustment,
alteration or service can cause injury or
damage. We decline any responsibility for
injury or damage, to persons or property, as a
result of improper installation.
Before Installation:
Before Installation, please decide the extraction
mode with the adjuster on the motor (Fig. 1).
Fig. 1
DUCTING RECIRCULATING
Rangehood standard confi guration
This product has been supplied with
“recirculation mode” as the default setting.
The rangehood is suitable for both recirculation
(Fig 3.) and external ducting (Fig. 2) modes
Fig. 2 Fig. 3
External Outdoor Ducting Mode
Recommended wherever possible for optimal
performance
If you have chosen to operate your rangehood in
“External Outdoor Ducting Mode” you will need
to follow the steps below:
1. Unscrew the 80mm fascia rail which is already
installed on the rangehood (Fig. 4)
2. Using the same screws, attach the 40mm
fascia rail (part ID 3, Installation Kit) supplied
in the box
3. Remove the aluminium grease fi lters (Fig 6. on
page 10) from the underside of the rangehood.
Turn the switch in the centre of the motor
housing to “External Outside Ducting” position
(Fig. 1)
4. Remove the charcoal fi lters by twisting anti-
clockwise (Fig. 8 on page 11). The charcoal
fi lters are not required for “external outdoor
ducting mode”
5. Clip in the plastic Front Vent Cover (part ID 9,
installation kit) over the vent holes on the front
of the rangehood.
6. Using the screws provided, install the Flu
Outlet Adaptor (Part ID 10, Installation kit)
to the top of the rangehood
7. Install the ducting pipe (not supplied) to the
outlet on the top of the rangehood and
vent to external air. It is recommended that
the ducting pipe is 120mm in diameter.
Fig. 4

7
8
INSTALLATION
Installation Kit
The installation kit contains the following parts:
Part ID Description Illustration Qty
1 Rangehood 1
2Rear-underside support mounting
bracket 1
3 40mm Height Front Fascia Rail 1
4Charcoal Filters
—Already installed
1 set
(2 pcs)
5 Screws (ST4 x 30mm) 6
6 Screws (ST4 x 8mm) 2
7 Wall Plugs (8mm) 6
8 Flat Washers 6
9Front Vent Cover
—If external ducting selected 1
10 Flu Outlet Adapter 1
9
Unpacking
• This product has been packaged to protect
it against transportation damage. Unpack
the appliance and remove all packaging
materials from around the rangehood. Keep
all packaging materials until you have made
sure your new rangehood is undamaged
and in good working order. The carton is
recyclable. Whenever possible, reuse the
carton and recycle it when disposing of
the packaging materials.
• Plastic wrapping can be a suffocation hazard
for babies and young children, so ensure all
packaging materials are out of their reach,
and dispose of them safely.
Important installation advice
WARNING!
• All electrical work associated with the
installation of this rangehood must be carried
out by a licensed electrician.
• This rangehood must be correctly installed by
a suitably qualifi ed person in strict accordance
with all applicable rules and regulations and
following the instructions in this manual.
• Do not try to install the rangehood yourself;
doing so will expose you to danger and void
the warranty. Improper installation, adjustment,
alteration or service can cause injury or
damage. We decline any responsibility for
injury or damage, to persons or property, as a
result of improper installation.
Before Installation:
Before Installation, please decide the extraction
mode with the adjuster on the motor (Fig. 1).
Fig. 1
DUCTING RECIRCULATING
Rangehood standard confi guration
This product has been supplied with
“recirculation mode” as the default setting.
The rangehood is suitable for both recirculation
(Fig 3.) and external ducting (Fig. 2) modes
Fig. 2 Fig. 3
External Outdoor Ducting Mode
Recommended wherever possible for optimal
performance
If you have chosen to operate your rangehood in
“External Outdoor Ducting Mode” you will need
to follow the steps below:
1. Unscrew the 80mm fascia rail which is already
installed on the rangehood (Fig. 4)
2. Using the same screws, attach the 40mm
fascia rail (part ID 3, Installation Kit) supplied
in the box
3. Remove the aluminium grease fi lters (Fig 6. on
page 10) from the underside of the rangehood.
Turn the switch in the centre of the motor
housing to “External Outside Ducting” position
(Fig. 1)
4. Remove the charcoal fi lters by twisting anti-
clockwise (Fig. 8 on page 11). The charcoal
fi lters are not required for “external outdoor
ducting mode”
5. Clip in the plastic Front Vent Cover (part ID 9,
installation kit) over the vent holes on the front
of the rangehood.
6. Using the screws provided, install the Flu
Outlet Adaptor (Part ID 10, Installation kit)
to the top of the rangehood
7. Install the ducting pipe (not supplied) to the
outlet on the top of the rangehood and
vent to external air. It is recommended that
the ducting pipe is 120mm in diameter.
Fig. 4
WARNING!
•All electrical work associated with the
installation of this rangehood must be carried
out by a licensed electrician.
•This rangehood must be correctly installed by
a suitable qualified person in strict accordance
with all applicable rules and regulations and
following the instructions in this manual.
•Do not try to install the rangehood yourself;
doing so will expose you danger and void the
warranty. Improper installation, adjustment,
alteration or service can cause injury or damage.
We decline any responsibility for injury or
damage, to persons or property,as a result of
improper installation.

8
11
Installation height:
For optimum performance, it is recommended that the rangehood be installed at a height of
between 650-750mm from the cooking surface. See Fig. 10 for detailed AS/NZS minimum distance
requirements.
Rear-mounting to the wall
• Using a spirit level, mark a horizontal line on the wall where the rangehood base will be, observing
all necessary clearances (Fig. 10). Check the required clearances in your cooktop/stove manual and,
should they be greater than those specifi ed in Fig. 10, make sure to observe them.
Fig. 10
Minimum distance
– Electric: 600mm
– Gas: 650mm
Maximum distance
– Either: 750mm
Top of
cooktop
Rangehood base
• Drill 4 holes of Ø8mm on the wall, as illustrated below (Fig. 11).
• Hammer the wall plugs into the holes, then insert two ST4x30mm screws into the lower wall plugs.
Tighten the screws, but leave a 2mm gap so that you can hang the rangehood on the screws in the
keyhole slots.
• Hang the hood to the wall screws, and make sure the hood is in balance and positioned correctly.
• Take away the Aluminum Filters, mark and drill another 2 holes of Ø8mm on the wall . (Safety Screw
Holes)
• Take back the hood and hammer the wall plugs, hang the hood again and fi x the hood with two
ST4x30mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 11
10
White Plastic Cover
• When choosing the outdoor exhausting mode,
you can cover the front outlet (part ID 9) with
the white plastic cover. (fig. 5).
Fig. 5
Recirculation Mode
This mode is the default setting. The rangehood
will operate with carbon filters and vent the air
back into the kitchen.
To ensure that the mode is correct, remove the
grease filters (see Fig. 6) and check that the
switch is in “Recirculation mode” position (Fig. 1).
Fig. 6
Charcoal filters
• If you intend to use the rangehood with the
air recirculating back into the kitchen, it is
important that you use the charcoal filters that
are already installed to prevent the odours
generated through cooking from being vented
back into the kitchen.
• Before installing the rangehood into the
cabinet, please remember to remove the
adhesive transit support tape on the carbon
filters first (Fig. 7).
Removing and Installing Charcoal filters
To remove the charcoal filters you will first need
to remove the grease filters (see Fig. 6), now twist
anti-clockwise and pull down as shown in Fig. 8.
Fig. 8
To install new charcoal filters you will need to first
remove the grease filters (Fig. 9), now align the
charcoal filters with the centre of the motors, twist
clockwise (Fig. 9) and push upwards until they
lock into place.
Fig. 9
Fig. 7
11
Installation height:
For optimum performance, it is recommended that the rangehood be installed at a height of
between 650-750mm from the cooking surface. See Fig. 10 for detailed AS/NZS minimum distance
requirements.
Rear-mounting to the wall
• Using a spirit level, mark a horizontal line on the wall where the rangehood base will be, observing
all necessary clearances (Fig. 10). Check the required clearances in your cooktop/stove manual and,
should they be greater than those specifi ed in Fig. 10, make sure to observe them.
Fig. 10
Minimum distance
– Electric: 600mm
– Gas: 650mm
Maximum distance
– Either: 750mm
Top of
cooktop
Rangehood base
• Drill 4 holes of Ø8mm on the wall, as illustrated below (Fig. 11).
• Hammer the wall plugs into the holes, then insert two ST4x30mm screws into the lower wall plugs.
Tighten the screws, but leave a 2mm gap so that you can hang the rangehood on the screws in the
keyhole slots.
• Hang the hood to the wall screws, and make sure the hood is in balance and positioned correctly.
• Take away the Aluminum Filters, mark and drill another 2 holes of Ø8mm on the wall . (Safety Screw
Holes)
• Take back the hood and hammer the wall plugs, hang the hood again and fi x the hood with two
ST4x30mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 11

9
11
Installation height:
For optimum performance, it is recommended that the rangehood be installed at a height of
between 650-750mm from the cooking surface. See Fig. 10 for detailed AS/NZS minimum distance
requirements.
Rear-mounting to the wall
• Using a spirit level, mark a horizontal line on the wall where the rangehood base will be, observing
all necessary clearances (Fig. 10). Check the required clearances in your cooktop/stove manual and,
should they be greater than those specifi ed in Fig. 10, make sure to observe them.
Fig. 10
Minimum distance
– Electric: 600mm
– Gas: 650mm
Maximum distance
– Either: 750mm
Top of
cooktop
Rangehood base
• Drill 4 holes of Ø8mm on the wall, as illustrated below (Fig. 11).
• Hammer the wall plugs into the holes, then insert two ST4x30mm screws into the lower wall plugs.
Tighten the screws, but leave a 2mm gap so that you can hang the rangehood on the screws in the
keyhole slots.
• Hang the hood to the wall screws, and make sure the hood is in balance and positioned correctly.
• Take away the Aluminum Filters, mark and drill another 2 holes of Ø8mm on the wall . (Safety Screw
Holes)
• Take back the hood and hammer the wall plugs, hang the hood again and fi x the hood with two
ST4x30mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 11
10
White Plastic Cover
• When choosing the outdoor exhausting mode,
you can cover the front outlet (part ID 9) with
the white plastic cover. (fig. 5).
Fig. 5
Recirculation Mode
This mode is the default setting. The rangehood
will operate with carbon filters and vent the air
back into the kitchen.
To ensure that the mode is correct, remove the
grease filters (see Fig. 6) and check that the
switch is in “Recirculation mode” position (Fig. 1).
Fig. 6
Charcoal filters
• If you intend to use the rangehood with the
air recirculating back into the kitchen, it is
important that you use the charcoal filters that
are already installed to prevent the odours
generated through cooking from being vented
back into the kitchen.
• Before installing the rangehood into the
cabinet, please remember to remove the
adhesive transit support tape on the carbon
filters first (Fig. 7).
Removing and Installing Charcoal filters
To remove the charcoal filters you will first need
to remove the grease filters (see Fig. 6), now twist
anti-clockwise and pull down as shown in Fig. 8.
Fig. 8
To install new charcoal filters you will need to first
remove the grease filters (Fig. 9), now align the
charcoal filters with the centre of the motors, twist
clockwise (Fig. 9) and push upwards until they
lock into place.
Fig. 9
Fig. 7
WARNING: Failure to install the screws or fixing device in according with these instructions may result
in electrical hazards!
11
Installation height:
For optimum performance, it is recommended that the rangehood be installed at a height of
between 650-750mm from the cooking surface. See Fig. 10 for detailed AS/NZS minimum distance
requirements.
Rear-mounting to the wall
• Using a spirit level, mark a horizontal line on the wall where the rangehood base will be, observing
all necessary clearances (Fig. 10). Check the required clearances in your cooktop/stove manual and,
should they be greater than those specifi ed in Fig. 10, make sure to observe them.
Fig. 10
Minimum distance
– Electric: 600mm
– Gas: 650mm
Maximum distance
– Either: 750mm
Top of
cooktop
Rangehood base
• Drill 4 holes of Ø8mm on the wall, as illustrated below (Fig. 11).
• Hammer the wall plugs into the holes, then insert two ST4x30mm screws into the lower wall plugs.
Tighten the screws, but leave a 2mm gap so that you can hang the rangehood on the screws in the
keyhole slots.
• Hang the hood to the wall screws, and make sure the hood is in balance and positioned correctly.
• Take away the Aluminum Filters, mark and drill another 2 holes of Ø8mm on the wall . (Safety Screw
Holes)
• Take back the hood and hammer the wall plugs, hang the hood again and fi x the hood with two
ST4x30mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 11

10
12
Top-mounting in a cabinet
• Determine where in the top cabinet you want to install the rangehood, then drill 4 holes of Ø4mm at
the bottom of the hanging board of your cabinet (Fig. 12).
Fig. 12
30.5mm
215mm
450mm
• Install the rangehood onto the bottom of the cupboard and secure it in place with four ST4x30mm
screws (Fig 13).
• If there is a space between the wall and the rear of the rangehood, install the rear-underside support
mounting bracket (Part ID 2, Installation kit) using the two ST4x8mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 13
7
PRODUCT OVERVIEW
1
2
3
4
6
7
5
KEY 1 Rangehood housing
2 Slide-out Front Fascia Rail
3 Inner Aluminium Grease Filter
4 Outer Aluminium Grease Filter
5 On/Off Switch
6 Fan Speed Switch
7 Light
7
PRODUCT OVERVIEW
1
2
3
4
6
7
5
KEY 1 Rangehood housing
2 Slide-out Front Fascia Rail
3 Inner Aluminium Grease Filter
4 Outer Aluminium Grease Filter
5 On/Off Switch
6 Fan Speed Switch
7 Light
WARNING: Failure to install the screws
or fixing device in according with these
instructions may result in electrical hazards!
Fig. 13
12
Top-mounting in a cabinet
• Determine where in the top cabinet you want to install the rangehood, then drill 4 holes of Ø4mm at
the bottom of the hanging board of your cabinet (Fig. 12).
Fig. 12
30.5mm
215mm
450mm
• Install the rangehood onto the bottom of the cupboard and secure it in place with four ST4x30mm
screws (Fig 13).
• If there is a space between the wall and the rear of the rangehood, install the rear-underside support
mounting bracket (Part ID 2, Installation kit) using the two ST4x8mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 13

11
12
Top-mounting in a cabinet
• Determine where in the top cabinet you want to install the rangehood, then drill 4 holes of Ø4mm at
the bottom of the hanging board of your cabinet (Fig. 12).
Fig. 12
30.5mm
215mm
450mm
• Install the rangehood onto the bottom of the cupboard and secure it in place with four ST4x30mm
screws (Fig 13).
• If there is a space between the wall and the rear of the rangehood, install the rear-underside support
mounting bracket (Part ID 2, Installation kit) using the two ST4x8mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 13
Your InAlto Rangehood
7
PRODUCT OVERVIEW
1
2
3
4
6
7
5
KEY 1 Rangehood housing
2 Slide-out Front Fascia Rail
3 Inner Aluminium Grease Filter
4 Outer Aluminium Grease Filter
5 On/Off Switch
6 Fan Speed Switch
7 Light
7
PRODUCT OVERVIEW
1
2
3
4
6
7
5
KEY 1 Rangehood housing
2 Slide-out Front Fascia Rail
3 Inner Aluminium Grease Filter
4 Outer Aluminium Grease Filter
5 On/Off Switch
6 Fan Speed Switch
7 Light
12
Top-mounting in a cabinet
• Determine where in the top cabinet you want to install the rangehood, then drill 4 holes of Ø4mm at
the bottom of the hanging board of your cabinet (Fig. 12).
Fig. 12
30.5mm
215mm
450mm
• Install the rangehood onto the bottom of the cupboard and secure it in place with four ST4x30mm
screws (Fig 13).
• If there is a space between the wall and the rear of the rangehood, install the rear-underside support
mounting bracket (Part ID 2, Installation kit) using the two ST4x8mm screws.
WARNING: Failure to install the screws or fi xing device in accordance with these instructions may
result in electrical hazards!
Fig. 13

12
13
This switch is to turn the rangehood
either on or off.
I Turns the rangehood ON
O Turns the rangehood OFF
This button toggles between fan speed high,
fan speed low and off setting
= Turns on the fan motors to high speed
for maximum extraction
O Turns off the fan motors for no extraction,
the fan motors are off
– Turns on the fan motors to low speed
minimum extraction
NOTE:
• The rangehood will only operate once the
slide-out rail is pulled outwards towards the
kitchen.
• Close the front panel and the rangehood will
stop working.
• The next time the front panel is pulled back
out, the rangehood will start working at the
previously set level.
OPERATING INSTRUCTIONS
THIS PAGE IS INTENTIONALLY LEFT BLANK

13
Operation Instructions
6
Controls
OPERATING YOUR RANGEHOOD
When the rangehood is plugged up, the ‘1’ key would start to shining, the
rangehood come to the standby mode. Press the keys to start the using.
–Short press the ‘1’ key, the rangehood will operate at low speed.
–Short press the ‘2’ key, the rangehood will operate at a medium speed.
–Short press the ‘3’ key, the rangehood will operate at a high speed.
–Short press the ‘B’ key, the rangehood will operate at a highest speed. 5
minutes working in this mode, the motor would change to 3rd speed
automatically.
–Short press the ‘Light’ key and the LED pan will come on. To turn the lights off,
simply press the ‘Light’ key again.
–Long press the ‘Light’ key , the rangehood would come to the 5 minutes timer,
with the ‘Light’ key shinning. After 5 minutes working, the motor would stop
automatically.
– To switch the rangehood motor or light off, simply press the key a second time.
13
This switch is to turn the rangehood
either on or off.
I Turns the rangehood ON
O Turns the rangehood OFF
This button toggles between fan speed high,
fan speed low and off setting
= Turns on the fan motors to high speed
for maximum extraction
O Turns off the fan motors for no extraction,
the fan motors are off
– Turns on the fan motors to low speed
minimum extraction
NOTE:
• The rangehood will only operate once the
slide-out rail is pulled outwards towards the
kitchen.
• Close the front panel and the rangehood will
stop working.
• The next time the front panel is pulled back
out, the rangehood will start working at the
previously set level.
OPERATING INSTRUCTIONS
NOTE:

14
Cleaning & Maintenance
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE: The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
NOTE:
NOTE:
CAUTION!
•Before cleaning the rangehood or carrying
out maintenance, make sure the operation
and light switches are set to the “ 0 ” position
and the rangehood is disconnection from the
power supply.
•It is important to clean the filters regularly
as oil and food residues can become a
fire hazard.
•Never use a steam cleaner to clean any part
of the rangehood.

15
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE: The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE: The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
Replacing the light bulb
If the light lamp needs replacing, proceed as follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Push out the lamp by hand from its back, pull out the lamp
connecting lines together;
• Open the protection cover as shown in the picture below,
and unplug the connected plastic shell to replace a new lamp.
Open the protective cover
Unplug the lines

16
Troubleshooting
& Technical Data
14
Troubleshooting guide
If you experience problems with your rangehood, or it appears not to be operating correctly, check in
the list below for answers to frequently asked questions. If none of the solutions offered help you solve
your problem, please contact our after sales support line for advice.
Do not attempt to repair the appliance yourself!
Problem Possible Cause Solution
The extractor fan ceases to
function. There is no electrical current in
the network.
Check with other appliances
that your electricity supply is
in working order.
There is insufficient suction
power. Wrong suction speed has
been selected, or the air outlet
is blocked.
Select suction speed “ II ”
if speed “ I ” was selected.
The charcoal filter needs to
be replaced. The charcoal
filter needs to be replaced if
food smells start to become
noticeable within your kitchen.
If the rangehood is installed
to vent outside, check that the
ducting and outlets are free
of blockages.
Make sure your kitchen is
adequately vented to allow
the entry of fresh air.
The rangehood has switched off
during operation. The safety cut-out device
has been tripped.
Turn off the rangehood and wait
for the device to reset.
If the rangehood has been
installed below the height levels
indicated in the “Installation”
section, the motor will cut out
frequently, which may damage
the rangehood.
The bulbs do not light up. The bulbs are loose,
or burnt out.
Tighten the bulbs, or replace
them, if necessary.
FAQ
Do not attempt to repair the appliance by yourself!

17
14
Troubleshooting guide
If you experience problems with your rangehood, or it appears not to be operating correctly, check in
the list below for answers to frequently asked questions. If none of the solutions offered help you solve
your problem, please contact our after sales support line for advice.
Do not attempt to repair the appliance yourself!
Problem Possible Cause Solution
The extractor fan ceases to
function. There is no electrical current in
the network.
Check with other appliances
that your electricity supply is
in working order.
There is insufficient suction
power. Wrong suction speed has
been selected, or the air outlet
is blocked.
Select suction speed “ II ”
if speed “ I ” was selected.
The charcoal filter needs to
be replaced. The charcoal
filter needs to be replaced if
food smells start to become
noticeable within your kitchen.
If the rangehood is installed
to vent outside, check that the
ducting and outlets are free
of blockages.
Make sure your kitchen is
adequately vented to allow
the entry of fresh air.
The rangehood has switched off
during operation. The safety cut-out device
has been tripped.
Turn off the rangehood and wait
for the device to reset.
If the rangehood has been
installed below the height levels
indicated in the “Installation”
section, the motor will cut out
frequently, which may damage
the rangehood.
The bulbs do not light up. The bulbs are loose,
or burnt out.
Tighten the bulbs, or replace
them, if necessary.
FAQ
16
Spare parts
Our after sales support centre stocks a wide range of spare parts for the Rangehood. To
purchase a part, call the centre on 1300 11 43 57 or email us at suppor[email protected]
• Blower • Charcoal filter • Connection box and bar
•Ducting •Switch •Slider
• Lamp & lamp holder • Motor • Outlet
• Reflector • Filter (aluminium mesh, inner and outer)
Specifications
Rated voltage/frequency AC 220-240V 50Hz
Dimensions (H×W×D)
Extended depth 278-472mm
Height of front panel 40mm/80mm
Weight
Motor power 2 × 100W
Lamp power 1 × 2W
Total input power 202W
Housing Painted white with stainless steel trim
Filters 2 Aluminium mesh filters
Accessories supplied 1 Set of charcoal filters
This product complies with AS/NZS 60335.2.31:2004+A1:2006
+A2:2007+A3:2009+A4:2010 for electrical safety, and with EN 55014-1:2006+A1:2009+A2:2011 for
electromagnetic compatibility.
Responsible disposal
At the end of their working life, do not throw any of these appliances out with your household
rubbish. Electrical and electronic products contain substances that can have a detrimental effect
on the environment and human health if disposed of inappropriately. Observe any local regulations
regarding the disposal of electrical consumer goods and dispose of it appropriately for recycling.
Contact your local authorities for advice on recycling facilities in your area.
Dimensions (H×W×D)
ASL60DR2S:176mm×599mm×278mm
ASL90DR2S:176mm×899mm×278mm
Weight
ASL60DR2S:9.2kg
ASL90DR2S:10.5kg

18
to this page
Attach your receipt

19
For future reference, please record the following information in the form below. The product details can be found on the
rating plate (located within the rangehood, behind the grease filters), installation details and purchase details which can
be found on your sales invoice.
STORE DETAILS
STORE NAME
|
ADDRESS
|
TELEPHONE
|
PURCHASE DATE
|
PRODUCT DETAILS
MODEL NO.
|
SERIAL NO.*
|
INSTALLATION DETAILS
DATE OF INSTALLATION
|
INSTALLED BY
|
Purchase Details

20
AUSTRALIAN WARRANTY TERMS & CONDITIONS
RANGEHOOD APPLIANCES
This document sets out the terms and conditions
of the product warranties for Residentia Group
Appliances. It is an important document. Please keep
it with your proof of purchase documents in a safe
place for future reference should you require service
for your Appliance.
1. IN THIS WARRANTY
(a) ‘acceptable quality’ as referred to in clause 10 of
this warranty has the same meaning referred to
in the ACL;
(b) ‘ACL’ means Trade Practices Amendment
(Australian Consumer Law) Act (No.2) 2010;
(c) ‘Appliance’ means any Residentia Group product
purchased by you accompanied by this document;
(d) ‘ASR’ means Residentia Group authorised service
representative;
(e) ‘Residentia Group’ means Residentia Group Pty
Ltd of 165 Barkly Avenue Burnley VIC, ACN 600
546 656 in respect of Appliances purchased in
Australia;
(f ) ‘major failure’ as referred to in clause 10 of this
warranty has the same meaning referred to
in the ACL and includes a situation when an
Appliance cannot be repaired or it is uneconomic
for Residentia Group, at its discretion, to repair an
Appliance during the Warranty Period;
(g) ‘Warranty Period’ means:
(i) where the Appliance is used for personal,
domestic or household use (i.e. normal
single family use) as set out in the
instruction manual, the Appliance is
warranted against manufacturing defects
for 36 months, following the date of
original purchase of
the Appliance;
(h) ‘you’ means the purchaser of the Appliance not
having purchased the Appliance for re-sale, and
‘your’ has a corresponding meaning.
2. This warranty only applies to Appliances
purchased and used in Australia and is in
addition to (and does not exclude, restrict, or
modify in any way) any non-excludable statutory
warranties in Australia.
3. During the Warranty Period Residentia Group or
its ASR will, at no extra charge if your Appliance
is readily accessible for service, without special
equipment and subject to these terms and
conditions, repair or replace any parts which it
considers to be defective. Residentia Group or
its ASR may use remanufactured parts to repair
your Appliance. You agree that any replaced
Appliances or parts become the property of
Residentia Group. This warranty does not apply
to light globes, batteries, filters or similar
perishable parts.
4. Parts and Appliances not supplied by Residentia
Group are not covered by this warranty.
5. You will bear the cost of transportation, travel
and delivery of the Appliance to and from
Residentia Group or its ASR. If you reside outside
of the service area, you will bear the cost of:
(a) travel of an authorised representative;
(b) transportation and delivery of the Appliance
to and from Residentia Group or its ASR, in all
instances, unless the Appliance is transported
by Residentia Group or its ASR, the Appliance is
transported at the owner’s cost and risk while in
transit to and from Residentia Group or its ASR.
6. Proof of purchase is required before you can make
a claim under this warranty.
7. You may not make a claim under this warranty
unless the defect claimed is due to faulty or
defective parts or workmanship. Residentia Group
is not liable in the following situations (which are
not exhaustive):
Warranty Information