Inbike 528 User manual

INBIKE 528 Bike Computer Instruction
Fuctions

SPD Speed
ODO Total cycling distance
DSTOne-pass cycling distance
MXSMaximum speed
AVSAverage speed
TMOne-pass cycling time

CLK Clock
SCANAutomatic Cycleplay
BACKLIGHT

SW Stop-watch
CDDCount-down distance
CDTCount-down time
CALConsumed calorie
FATConsumed fat
TEMTemperture

Alter For power shortage
Power saving
‘+’& ‘-‘ Speed comparing
Upkeep reminding
KM/hr M/hr setting
Wheel perimeter setting
Total distance initial value setting
Cycling date sampling
Automotive wake-up
Installation of Battery
Open the battery lid with a coin. Put in a 3V CR2032 Battery. ( Positive pole upwards)
Installation of inductor & Magnet
Install the Inductor on the front fork ( Same side as the magnet),Fix the inductor with the
complimentary armor tape, twine the wire on the handlebar.(Fix with armor
tape) ,Adjust the position between the magnet and inductor, make the distance around
1.5mm.(The closer ,the Better) .When fix the magnet, never let the magnet towards the
centre of inductor, make the magnet towards to the upside or downside of the inductor.
Installation of the computer base
Fix with the armor tape

Installation of the computer
Press the computer into the base, Rotate clockwise.
Wheel perimeter setting
1. Record the size marked on the wheel , find out the perimeter by referring to the
follow chart
2. Draw a spot on the wheel, then push the bike, The distance is the wheel perimeter when
the spot runs a circle.
Press the right button to change the number, Press left button to confirm and set the next
parameter.
The wheel perimeter must be accurate.
Km/hr / M/hr selection
After setting the perimeter of wheel. Press left button to
select speed unit. Press right button to alter Km/hr or M/hr
Weight setting
Acquiescent weight unit is K(kg), Press right button to switch
KG(kilogram) or L (pound), press left button to confirm. Press
left button to adjust the weight number. Press left button to
enter the upkeep remind setting page.
Upkeep remind setting
Acquiescent remind number is 200(Km/M) , You could adjust
the number by pressing right button. When the total cycling
distance reaches, The wrench symbol will flicker. press the
right button 3 seconds to remove the recorded number.
All initial setting have completed till this step, Your cycling
date will be recorded
Function switching
Press right button to switch the mode.
ODO – DST – MEX – AVS – TM – SW – CDD – CDT – CAL – FAT – TEM – SCAN - CLOCK

Clock setting( 12/24 hr)
Press left button 3 seconds to set 12/24hr mode. Press left button
to switch 12hr/24hr. Press right button to set the hour, press right
button to adjust the number. Left button adjust the number. Right
button confirm. Press right button to view the ODO.
ODO (Total cycling distance)
Press left button 3 seconds to set the number. Left button adjust the
number. Right button confirm. ( When change the battery, Please
record the ODO number) Press right button to view the DST.
DST (One-pass cycling distance)
The total distance when (TM)One-pass cycling time start. Press left
button 3 second to delete the DST date. Meanwhile the MXS,AVS
& TM date will be deleted. Press right button to view the MXS.
MXS (Maximum speed)
One-pass cycling maximum speed. Press left button 3 second to
delete the MXS date. Meanwhile the DST,AVS & TM date will be
deleted. Press right button to view the AVS.
AVS(One-pass average speed)
One-pass cycling average speed. Press left button 3 second to
delete the AVS date. Meanwhile the DST, MXS & TM date will be
deleted. Press right button to view the TM.
TM (One-pass cycling time)
One-pass cycling time. Press left button 3 second to delete the TM
date. Meanwhile the DST, MXS & AVS date will be deleted. Press
right button to view the SW.
SW (Stop-watch)
Press left button to start. Press left button again to stop. Press right
button to delete .Press left button 3 seconds to lock at the SW page.
Press left button 3 seconds again to unlock. Press the right button
to view CDD.

(CDD) Count-down distance
Press left button 3 seconds to begin count-down distance setting,
Left button adjust the number. Right button confirm. Press the right
button to view CDT.
(CDT) Count-down time
Press left button 3 seconds to begin count-down time setting, Left
button adjust the number. Right button confirm. Press the right
button to view CAL.
(CAL) Consumed calorie
The calorie consumed in cycling. Press left button 3 seconds to delete
the date.
(FAT) Consumed Fat
The fat consumed in cycling. Press left button 3 seconds to delete
the date.
(TEM) Temperature
Current temperature, Press left button 3 seconds to change the unit.
(C°/ F°)Press right button to enter SCAN mode.
(SCAN) Automatic Cycleplay
Screen will shows DST, MXS ,AVS ,TM successively. Press right button
to end the SCAN and enter Clock mode.
Power saving mode
If there is no input within 300 seconds. The screen will turn off.(show
the clock only). The screen will turn on when receive any input or
cycling signal.
Cycling date sampling
Press left button at any mode, the computer will enter cycling date sampling. The bottom
of the screen will show flickering cycling time(TM ), press right button to view sampled
cycling distance(DST) ,cycling time(TM ), cycling average speed (AVS), Maximum speed
(MXS).
Press left button again to quit sampling.

Resetting
Press both left and right button 3 seconds to reset distance unit(KM/M) , wheel perimeter,
weight & upkeep remind distance. The original date will be kept.
Current speed
The current speed will show at the top position.
Speed comparing
‘+’ means current speed exceed average speed, ‘--’ means current
speed is under average speed.
Alter for power shortage
When the voltage of battery is under 2.5 V , battery symbol will
appear for reminding you to change battery.
Backlight
The backlight will turn on when you press any button 18:00 to 6:00.
Malfunction & reasons
Malfunction
Reasons
Speed show ’0’ when cycling
1.The distance or install position has problem
between magnet and inductor;
2.Power shortage
Wrong Speed value
wheel perimeter is incorrect
Screen display slowly-react
Computer work under 0°
Blank screen
Expose under light for a long time
Screen unclear
Power shortage or battery poor contact