Indesit WIDXL 86 User manual

29
GB
English
Contents
Installation, 30-31-32-33
Unpacking and levelling
Electric and water connections
The first wash cycle
Technical details
Washer-dryer description, 34-35
Control panel
Leds
tarting and Programmes, 36
Briefly: how to start a programme
Programme table
Personalisations, 37
Setting the temperat re
Setting the drying cycle
F nctions
Detergents and laundry, 38
Detergent dispenser
Preparing yo r la ndry
Special items
Precautions and advice, 39
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 40
C tting off the water or electricity s pply
Cleaning yo r appliance
Cleaning the detergent dispenser
Caring for yo r appliance door and dr m
Cleaning the p mp
Checking the water inlet hose
Troubleshooting, 41
ervice, 42
Before calling for Assistance
WA HER-DRYER
WIDXL 86
Instructions for use
GB

30
GB
Keep this instr ction man al in a safe place for
f t re reference. Sho ld the appliance be sold,
transferred or moved, make s re the instr ction
man al accompanies the Washer-dryer to inform the
new owner as to its operation and feat res.
Read these instr ctions caref lly: they contain vital
information on installation, se and safety.
Unpacking and levelling
Unpacking
1. Unpack the Washer-dryer.
2. Check whether the Washer-dryer has been
damaged d ring transport. If this is the case, do not
install it and contact yo r retailer.
3. Remove the fo r
protective screws and
the r bber washer with
the respective spacer,
sit ated on the rear of
the appliance (see
figure).
4. Seal the gaps sing the plastic pl gs provided.
5. Keep all the parts: yo will need them again if the
Washer-dryer needs to be moved to another location.
Packaging materials are not children's toys.
Levelling
1. Install the Washer-dryer on a flat st rdy floor,
witho t resting it p against walls, f rnit re cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any nevenness
by tightening or
loosening the adj stable
front feet (see figure);
the angle of inclination,
meas red according to
the worktop, m st not
exceed 2°.
Levelling yo r appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
d ring operation. If it is placed on a fitted or loose
carpet, adj st the feet in s ch a way as to allow
eno gh room for ventilation beneath the Washer-
dryer.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose
and screw the latter
onto a cold water tap
with a 3/4 gas threaded
mo th (see figure).
Before making the
connection, allow the
water to r n freely ntil
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the Washer-dryer,
screwing it onto the
appliance's cold water
inlet, sit ated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make s re there are no kinks or bends in the
hose.
The water press re at the tap m st be within the
val es indicated in the Technical details table
(on the next page).
If the water inlet hose is not long eno gh, contact
a specialist store or an a thorised serviceman.
 Never se hoses that have already been sed.
Installation
A

GB
Connecting the drain hose
Connect the drain hose,
witho t bending it, to a
draining d ct or a wall
drain sit ated between
65 and 100 cm from
the floor;
alternatively, place it
over the edge of a
basin, sink or t b,
fastening the d ct
s pplied to the tap (see
figure). The free end of
the hose sho ld not be
nderwater.
 We advise against the se of hose extensions; in
case of absol te need, the extension m st have the
same diameter as the original hose and m st not
exceed 150 cm in length.
Electric connection
Before pl gging the appliance into the mains
socket, make s re that:
 the socket is earthed and in compliance with the
applicable law;
 the socket is able to s stain the appliance's
maxim m power load indicated in the Technical
details table (see page 33);
 the s pply voltage is incl ded within the val es i
ndicated on the Technical details table
(see page 33);
 the socket is compatible with the washing
machine's pl g. If this is not the case, replace
the socket or the pl g.
Yo r appliance is now s pplied with a 13 amp f sed
pl g it can be pl gged into a 13 amp socket for
immediate se. Before sing the appliance please
read the instr ctions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a fa lty f se, a 13 amp ASTA
approved f se to BS 1362 sho ld always be sed, and
the f se cover re-fitted. If the f se cover is lost, the
pl g m st not be sed ntil a replacement is obtained.
Replacement f se covers:
If a replacement f se cover is fitted, it m st be of the
correct colo r as indicated by the colo red marking or
the colo r that is embossed in words on the base of
the pl g. Replacements can be obtained directly from
yo r nearest Service Depot.
Removing the plug:
If yo r appliance has a non-rewireable mo lded pl g
and yo sho ld wish to re-ro te the mains cable
thro gh partitions, nits etc., please ens re that
either:
the pl g is replaced by a f sed 13 ampere re-
wearable pl g bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
o tlet, controlled by a switch, (in compliance with
BS 5733) which is accessible witho t moving the
appliance.
Disposing of the plug:
Ens re that before disposing of the pl g itself, yo
make the pins n sable so that it cannot be
accidentally inserted into a socket.
Instr ctions for connecting cable to an alternative
pl g:
Important: the wires in the mains lead are colo red
in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
As the colo rs of the wires in the lead may not
correspond with the colo red markings identifyng
the terminals in yo r pl g, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or or colo red Green or Green & Yellow.
Connect Brown wire to terminal marked L or
colo red Red.
Connect Bl e wire to terminal marked N or colo red
Black.
65 - 100 cm

32
GB
If a 13 amp pl g (BS 1363) is sed it m st be fitted
with a
13 amp f se, either in the pl g or adaptor or at the
distrib tion board.
If yo are in any do bt the electrical s pply to yo r
machine, cons lt a q alified electrician before se.
How to connect an alternative pl g:
The wires in this mains lead are colo red in
accordance with the following code:
BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
pl g by c tting the mains cable as close as possible
to the pl g body and dispose of it as described
above.
 The washing machine sho ld not be installed in an
o tdoor environment, not even when the area is
sheltered, beca se it may be very dangero s to
leave it exposed to rain and th nderstorms.
 When the washing machine is installed, the mains
socket m st be within easy reach.
 Do not se extensions or m ltiple sockets.
 The power s pply cable m st never be bent or
dangero sly compressed.
 The power s pply cable m st only be replaced by
an a thorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
The first wash cycle
Once the appliance has been installed, and before
yo se it for the first time, r n a wash cycle with
detergent and no la ndry, setting the 90°C
programme witho t a pre-wash cycle.

GB
Technical details
Model WIDXL 86
Dimensions
59.5 cm wide
85 cm high
53.5 cm deep
Capacity from 1 to 6 kg for the wash programme;
from 1 to 5 kg for the drying programme
Electric
connections
please refer to the technical data plate
fixed to the machine
Wat e r
connections
maxim m press re 1 MPa (10 bar)
minim m press re 0.05 MPa (0.5 bar)
dr m capacity 52 litres
pin speed p to 800 rpm
Control
programmes
according to
EN 50229
directive
Wash: programme 2; temperat re 60°C;
r n with a load of 6 kg.
Drying: first drying cycle performed with
a 1 kg load, by selecting a drying time
of 60 min;
Second drying cycle performed with a 5
kg load and the DRYING knob on the
setting.
This appliance is compliant with the
following E ropean Comm nity
Directives:
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
s bseq ent amendments
- 2002/96/CE
- 2006/95/CE (Low Voltage)

34
GB
Washer-dryer description
Control panel
Detergent dispenser
ON-OFF
B tton
TART/RE ET
B tton
TEMPERATURE
Knob
PROGRAMME
Knob
Leds
FUNCTION
B ttons
ON-OFF/
DOOR
LOCK
Led
Detergent dispenser: to add detergent and fabric
softener (see page 38).
LED : to find o t which wash cycle phase is nder
way.
If the Delay Timer f nction has been set, the time
left ntil the programme starts will be indicated (see
page 35).
DRYING knob: to set the desired drying cycle
(see page 37).
FUNCTION b ttons: to select the f nctions
available. The b tton corresponding to the f nction
selected will remain on.
TEMPERATURE knob: to set the temperat re or
the cold wash cycle (see page 37).
TART/RE ET b tton: to start the programmes or
cancel any incorrect settings.
ON-OFF/DOOR LOCK Led: to find o t whether the
Washer-dryer is on and if the appliance door can be
opened (see page 35).
ON/OFF b tton: to t rn the Washer-dryer on and off.
PROGRAMME knob: to select the wash
programmes. The knob stays still d ring the cycle.
DRYING
Knob
Note: to avoid excessive vibrations before every spin cycle the machine distributes the load in a uniform manner
by continuously rotating the drum at a speed which is slightly faster than the normal washing speed.
When despite repeated attempts the load is still not evenly distributed the machine spins at a lower speed than
the set frequency.
If the load is excessively unbalanced the machine attempts to distribute it instead of spinning.
The balancing attempts may extend the total duration of the cycle up to a maximum of 10 minutes.

GB
ON-OFF/DOOR LOCK led:
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before yo open the appliance door.
 The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED
indicates there is an abnormality (see page 41).
Cycle phase under way:
D ring the wash cycle, the LEDs grad ally ill mina-
te on to indicate the cycle phase nder way:
Prewash / Wash
Rinse
Spin cycle
Drying
Note:
- d ring draining, the LED corresponding to the
Spin cycle phase will be t rned on.
- when the drying cycle is complete, the indicator
light relative to phase will flash, to indicate that
the DRYING knob needs to be set back to the 0
setting.
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a f nction is selected, the corresponding
b tton is ill minated.
If the f nction selected is incompatible with the
programme set, the b tton will flash and the
f nction will not be enabled.
If yo set a f nction that is incompatible with
another f nction yo selected previo sly, only the
last one selected will be enabled.
Leds
The LEDS provide important information.
This is what they can tell yo :
Delay set:
If the Delay Timer f nction has been enabled (see
page. 37), once yo have started the programme,
the LED corresponding to the delay set will begin to
flash:
As time passes, the remaining delay will be
displayed, and the corresponding LED will flash:
Once the set delay is complete, the flashing LED will
t rn off and the programme set will start.

36
GB
tarting and Programmes
Programme table
Briefly: starting a programme
1. Switch the Washer-dryer on by pressing b tton .
All the LEDS will light p for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load yo r la ndry into the washing machine and
sh t the appliance door.
3. Set the PROGRAMME knob to the programme
req ired.
4. Set the wash temperat re (see page 37).
5. Set the drying cycle if necessary (see page 37).
6. Add the detergent and any fabric softener (see page 38).
7. Start he programme by pressing the START/RESET
b tton.
To cancel it, keep the START/RESET b tton pressed
for at least 2 seconds.
8. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take o t yo r
la ndry and leave the appliance door ajar to allow
the dr m to dry thoro ghly. T rn the Washer-dryer
off by pressing b tton .
Notes
-For programme 9, we advise against exceeding a wash load of 3.5 kg.
-For programme 13 we advise against exceeding a wash load of 2 kg.
-For the anti-crease f nction: see Easy iron, opposite page. The information contained in the table is p rely indicative.
pecial programme
Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amo nt of time: it only lasts
30 min tes and allows yo to save on both time and energy. By setting this programme (11 at 30°C), yo can wash
different fabrics together (except for woollen and silk items), with a maxim m load of 3 kg.
We recommend the use of liquid detergent.
Type of fabric and
degree of soil Prog. Temp. Drying Cycle
Detergent Fabric
softener
Cycle
length
(minutes)
Description of ash cycle
pre-wash wash
tandard
Extremely soiled whites (sheets,
tablecloths, etc.) 190°C     155 Pre-wash, wash cycle, rinse cycles, intermediate and final spin cycles
Extremely soiled whites (sheets,
tablecloths, etc.) 290°C    150 Wash cycle, rinse cycles, intermediate
and final spin cycles
Heavily soiled whites and fast colo rs 260°C    140 Wash cycle, rinse cycles, intermediate
and final spin cycles
Heavily soiled whites and delicate colo rs 240°C    125 Wash cycle, rinse cycles, intermediate
and final spin cycles
Slightly soiled whites and delicate colo rs
(shirts, j mpers, etc.) 340°C    85 Wash cycle, rinse cycles, intermediate
and final spin cycles
Heavily soiled fast colo rs (baby linen, etc.) 460°C 
83 Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Heavily soiled fast colo rs (baby linen, etc.) 440°C    70 Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Wool 540°C   50 Wash cycle, rinse cycles, delicate
spin cycle
Very delicate fabrics (c rtains, silk,
viscose, etc.) 630°C   45 Wash cycle, rinse cycles, anti-
crease or draining cycle
Drying cotton 7
Drying delicates 8
Tim e 4 you
Heavily soiled whites and fast colo rs 960°C   60 Wash cycle, rinse cycles, intermediate
and final spin cycles
Delicate colo rs (all types of slightly soiled
garments) 10 40°C  40 Wash cycle, rinse cycles, delicate
spin cycle
Delicate colo rs (all types of slightly soiled
garments) 11 30°C    30 Wash cycle, rinse cycles and
delicate spin cycle
port
Sports shoes (MAX. 2 pairs) 12 30°C  50
Cold wash (witho t detergents),
wash cycle, rinse cycles, and delicate
spin cycle
Fabrics for sportswear
(Tracks its, shorts, etc.) 13 30°C   60 Wash cycle, rinse cycles, intermediate
and final spin cycles
PARTIAL PROGRAMME
Rinse   Rinse cycles and spin cycle
Spin cycle  Draining and spin cycle
Drain Drain

GB
Personalisations
C
etting the temperature
T rn the TEMPERATURE knob to set the wash temperat re (see Programme table on page 36).
The temperat re can be lowered, or even set to a cold wash ( ).
et the drying cycle
T rn the DRYING knob to set the desired drying type.
Two options are available:
A - Based on time: From 40 min tes to 180.
B - Based on the damp level of the dry clothes:
Iron : slightly damp clothes, easy to iron.
Hanger : dry clothes to p t away.
Cupboard : very dry clothes, recommended for towelling
and bathrobes.
A cooling stage is foreseen at the end of the drying cycle.
If yo r la ndry load to wash and dry is exceptionally in excess
of the maxim m load foreseen (see table opposite), perform
the wash cycle, and when the programme is complete, divide p the garments and p t part of them back in the
dr m. Now follow the instr ctions provided for a dry only cycle. Repeat this proced re for the remainder of the load.
Dry only
T rn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the
desired drying type sing the DRYING knob.
Important: - A spin cycle is carried o t d ring the drying if yo have set a cotton programme and a level of
dryness (C pboard , Hanger , Iron ).
- For cotton loads of less than 1 Kg use the drying programme designed for delicate fabrics.
Functions
To enable a f nction:
1. press the b tton corresponding to the desired f nction, according to the table below;
2. the f nction is enabled when the corresponding b tton is ill minated.
Note: The rapid flashing of the b tton indicates that the corresponding f nction cannot be selected for the
programme set.
Fabric
type
Load type Max.
load
(kg) Cup-
board
Hanger Iron
Cotton,
Linen
Clothing of different sizes 5 180 170 140
Cotton Terry towels 5 180 170 140
Terital,
Cotton
Sheets, Shirts 2,5 140 120 100
Acrylics Pyjamas, socks, etc. 170 6560
Nylon Slips, tights, stockings, etc. 170 6560
Table of drying times
The data contained in the
table are purely indicative.
Function Effect Comments Enabled ith
programmes:
Delay
Timer
Delays the start
of the wash by
p to 9 ho rs.
Press the b tton repeatedly ntil the LED corresponding to the
desired delay is t rned on.
The fifth time the b tton is pressed, the f nction will be disabled.
N.B.: Once yo have pressed the Start/Reset b tton, the delay
can only be decreased if yo wish to modify it.
All
Easy iron
This option
red ces the
amo nt of
creasing on
fabrics, making
them easier to
iron.
When this f nction is set, programmes 4, 6 will end with the
la ndry left to soak (Anti-crease) and the Rinse cycle phase
LED will flash.
- to concl de the cycle, press the START/RESET b tton;
- to r n the draining cycle alone, set the knob to the relative
symbol and press the START/RESET b tton.
This f nction is incompatible with the STAIN REMOVAL f nction.
3, 4, 6,
9, 10,
Rinse cycle.
Extra
Rinse
Increases the
efficiency of the
rinse.
Recommended when the appliance has a f ll load or with large
q antities of detergent.
1, 2, 3, 4, 9,
10, 12, 13,
Rinse cycle.
800-400
Red ces the
spin speed.
All
programmes
except for 6
and draining.

38
GB
Detergent dispenser
Good washing res lts also depend on the correct
dose of detergent: adding too m ch detergent won't
necessarily make for a more efficient wash, and may
in fact ca se b ild p on the interior of yo r
appliance and even poll te the environment.
Open p the detergent
dispenser and po r in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
(powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liq id detergent sho ld only be po red in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener sho ld not overflow from the grid.
 Do not se hand wash detergent beca se it may
form too m ch foam.
Preparing your laundry
 Divide yo r la ndry according to:
- the type of fabric/the symbol on the label.
- the colo rs: separate colo red garments from
whites.
 Empty all pockets and check for loose b ttons.
 Do not exceed the weight limits stated below,
which refer to the weight when dry:
St rdy fabrics: max 6 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1,5 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
pecial items
Curtains: fold c rtains and place them in a pillow
case or mesh bag. Wash them separately witho t
exceeding half the appliance load. Use programme 6
which excl des the spin cycle a tomatically.
Quilted coats and windbreakers: if they are
padded with goose or d ck down, they can be
machine-washed. T rn the garments inside o t and
load a maxim m of 2-3 kg, repeating the rinse cycle
once or twice and sing the delicate spin cycle.
Wool: for best res lts, se a specific detergent,
taking care not to exceed a load of 1,5 kg.
Detergents and laundry
123