INDY AUDIO LABS aragon 8008 User manual
28008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
1. Read Instructions – All safety and operating instructions should be
read before operating the device.
2. Retain Instructions – The safety and operating instructions should
be retained for future reference.
3. Heed Warnings – All warnings on the device and in the operating
instructions should be adhered to.
4. Follow instructions – All operating and safety instructions should
be followed.
5. Attachments – Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
6. Water and Moisture – Do not use this product near water (for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub;
in a wet basement; or near a swimming pool; and the like).
7. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
8. Heat – This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products that
produce heat.
9. Power Sources – This product should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supply in your home, consult with your
product dealer or the local power company. For products intended
to operate from battery power, or other sources, refer to the
operating instructions.
10. Grounding – This product is equipped with a three-wire grounding-
type plug, a plug having a third (grounding) pin. This plug will only
fit into a grounding-type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the safety purpose of
the grounding-type plug.
11. Power Cord Protection – Power supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.
12. Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire or
electrical shock.
13. Lightning and Periods of Non-Use – For added protection for this
product during a lightning storm, or when it is left unattended and
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
RISK OF ELECTRIC SHOCK!
DO NOT OPEN!
CAUTION! To reduce the risk of electric shock and fire, do not remove the cover or back plate of the device
enclosure. There are no user serviceable parts inside. Refer servicing to an Aragon authorized service center.
CAUTION! The international symbol of a lightning bolt inside a triangle is intended to alert the user to
uninsulated “dangerous voltage” within the device enclosure. The international symbol of an exclamation
point inside a triangle is intended to alert the user to the presence of important operating, maintenance and
servicing information in the manual accompanying the device.
WARNING! To reduce the risk of fire or electrical shock, do not expose this equipment to rain or moisture.
unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage
to the product due to lightning and power line surges.
14. Cleaning – Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
15. Object and Liquid Entry – Never push objects of any kind into this
product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
16. Damage Requiring Service – Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions: a) When the power supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water, d) If the product
does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result
in damage and often will require extensive work by a qualified
technician to restore the product to its normal operation, e) If the
product has been dropped or damaged in any way, or f) When the
product exhibits a distinct change in performance – this indicates a
need for service.
17. Replacement Parts – When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or that have the same characteristics as the original
parts. Unauthorized substitutions may result in fire, electric shock,
or other hazards.
18. Safety Check – Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
19. Servicing – Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
If this unit is purchased outside of the U.S., please contact your
local dealer or distributor for service center information. If purchased
inside the U.S. and dealer service is not available, contact Aragon
Customer Service for a return authorization (RA) number before
shipping. For further service information, contact:
ARAGON CUSTOMER SERVICE
phone: 1-866-781-7284
5225 EXPLORATION DRIVE
INDIANAPOLIS, IN 46241
3
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
2
Important Safety Instructions
5
Becoming Familiar withYour
New Aragon Amplifier
9
Operation
18
Design Notes
3
Contents
7
Placement and Setup
14
Problem Resolution
19
Warranty
4
Congratulations
Unpacking
8
System Planning and Optimizing
Making System Connections
16
Technical Specifications
20
About Aragon and
Indy Audio Labs
contents
48008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
congratulations
unpacking
Outer and Inner Carton
TEAM LIFT! -To Avoid injury, lift with
someone else - your amplifier is very heavy!
Package Contents
1.Aragon amplifier
2.Foam Bumpers (2)
3.Power Cord
4.XLR Shorting Plugs
5.User Guide
6.Warranty Card
ARAGON CUSTOMER SERVICE
phone: 1-866-781-7284
email: [email protected]
5225 EXPLORATION DRIVE
INDIANAPOLIS, IN 46241
Retain your Packaging
Register your Product
Record your Unit Information
5
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
becoming familiar
with your new
aragon amplifier
Front Panel
Power Button:
Pre-amp On/Off Control, p9
Status Light:
indication meaning
unlit No AC power input
steady red Low-power (idle) mode
flashing red Amplifier circuits initializing
blue Amplifier ON
Aragon’s Proprietary En-
hanced Ethernet Control (E2C), p10
Exterior Surfaces
Top Cover and Sides:
Central Heat Sink:
68008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
Rear and Bottom Panel
Rear panel finish:
Speaker Outputs:
Audio Inputs:
AC Mains Inlet:
Network Module:
1 - External 12VTrigger Input:
1
2
3
4
7
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
2 - System Controller (RS-232) Input:
3 - Ethernet Network Active LED:
4 - Ethernet Jack:
Feet:
placement
and setup
Shelf Mounting
Technical Specifications, p16
88008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
system planning
and optimizing
making system
connections
Speaker Outputs
Avoid connecting or disconnecting
loudspeaker wires with the amplifier in the
“On”state (blue status light) as damage to
the amplifier could occur.
9
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
Audio Inputs
Pre-amp On/Off Control (12VTrigger)
NOTE:The front panel power button functions
normally even if the trigger input is used.
The Aragon amplifier will automatically
resume control sync with the external preamp
after the next time system power is cycled.
Mains (AC) Power
Technical Specifications, p16
It is recommended practice to connect AC
power only after all other connections have
been made.
1/8”(3.5mm) stereo plug
1 – Ground
2 – Ground
3 –TriggerVoltage
Control Networks
Ethernet:
RS-232:
operation
Standby Mode
Before powering on, ensure that your preamp
volume level is not too high or else speaker
damage may occur.
1 2 3
10 8008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
LAST ON, FIRST OFF! –To avoid potential
loud pops and/or hum, always turn on the
amplifier last after other components such
as pre-amps and sources and turn off the
amplifier first when powering down.
Normal Operation
Source Material:
Break In Period:
When not in Use:
Aragon’s Proprietary Enhanced
Ethernet Control (E2C)
Setting up Enhanced Ethernet Control (E2C):
Manual Network Discovery:
MAC Address 00:03:75:XX:YY:ZZ
11
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
Discovering the IP address with a Mobile Device:
IP Discovery via Traditional Computer:
Amplifier Control and Status using E2C
Power:
Mute:
Channel Temperature Indicators:
Settings Button:
12 8008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
Settings Page:
Individual Channel Mute:
Front Panel Illumination Brightness Control:
Temperature Display Units:
13
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
About Information Section:
Network Settings:
model default ip address
Iridium 192.168.1.243
8008 192.168.1.242
14 8008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
problem resolution
TroubleshootingTable
problem or symptom possible causes recommendations
Amplifier does not power on –
no front panel lights
AC not connected • Check that power cord is connected at the wall and at the
back of the unit.
• Check that switched AC outlets are on.
• Check that power conditioner is on (if applicable).
Blown or missing mains fuse Check fuse compartment in back of unit near AC inlet.
Replace fuse and retest. If problem persists, refer unit to
service personnelle.
Amplifier powers on with red standby
light but does not switch on with blue
light indicator via web control
Control device not connected
to local network
• Check to ensure control device is connected to the local
network and not another neigboring network.
• Check to ensure that all network routers and switches are
powered up and active.
Amplifier disconnected from
local network
Check network activity light – if not illuminated green, check
opposite end of cable. If cable is plugged in and switch or
router shows activity indication, replace network cable.
Amplifier switches on (blue indicator)
but does not produce audio
Loudspeakers disconnected Check loudspeaker connections at the amplifier and at the
speaker terminals. Look for frayed or disconnected leads.
Pre-amp not powered on Check preamp power status.
Pre-amp not connected
properly
Check to ensure amplifier inputs are connected directly from
corresponding pre-amp outputs via good RCA or XLR cables.
Source device disconnected • Check connections between source device and pre-amp.
• Try using an alternate source device to eliminate the
possibility of a pre-amp problem.
Web control global or
channel mutes active
Using web control, check mute button states on main view
and advanced views. Alternately, reset AC power to the unit to
reset the mute states. Note that with DHCP control, this may
reset the unit IP address.
Only one of two amplifier channels
appear to be working (8008)
Shorted or open speaker leads Check loudspeaker connections at the amplifier and at the
speaker terminals. Look for frayed or disconnected leads.
Pre-amp not connected
properly
Check to ensure amplifier inputs are connected directly from
corresponding pre-amp outputs via good RCA or XLR cables.
Loudspeaker problem Disconnect problem loudspeaker and connect to a known
good loudspeaker.
Preamp or source device
surround mode problem
(applies primarily to home
theater applications)
Check that speaker sound is supported in the processing
mode that is active. For example, a center channel speaker
will be silent in Dolby Digital 2.0 mode. Likewise, for speech
playback, often the left and right front speakers will be silent
in Dolby Pro Logic mode. Refer to the information that came
with the preamp or source device.
Web control global or
channel mutes active
Using web control, check mute button states on main view
and advanced views. Alternately, reset AC power to the unit to
reset the mute states. Note that with DHCP control, this may
reset the unit IP address.
Blown channel protection
fuse(s)
Can sometimes occur after faulty connection to good
loudspeaker OR good connection to faulty loudspeaker.
15
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
Amplifier sound is garbled
or distorted
Shorted or open speaker leads Check loudspeaker connections at the amplifier and at the
speaker terminals. Look for frayed or disconnected leads.
Pre-amp not connected
properly
Check to ensure amplifier inputs are connected directly from
corresponding pre-amp outputs via good RCA cables.
Loudspeaker problem Disconnect problem loudspeaker and connect to a known
good loudspeaker.
Hum persists only when amplifier
is on – goes away in standby
Partially connected or faulty
RCA or XLR input cable
• Check for RCA plugs not seated completely in jacks
• Isolate and replace faulty cable.
Bad AC ground connection • Check to ensure the original 3-conductor heavy-guage
power cord that shipped with your Acurus is used for
the amplifier.
• Try a different power outlet in case the wall outlet ground
is defective.
• Attempt to power the system from a single AC outlet
to minimize ground loops.
Using RCA (unbalanced) input
without XLR Shorting Plugs
Insert the XLR Shorting Plugs that were provided
with your amplifier.
Cable or Sattelite TV connection
causing hum
Verify source by disconnecting incoming cable line or satellite
dish cable to see if hum disappears. If this is the source, then
hum will dissappear when the cable is disconnected from the
system. If so, us an isolation transformer (or Mondial Magic
Box) at each of the cable and/or satellite inputs.
Cannot control amplifier from mobile
device or computer
Control device not connected
to local network
• Check to ensure control device is connected to the local
network and not another neigboring network.
• Check to ensure that all network routers and switches are
powered up and active.
Amplifier disconnected from
local network
Check network activity light – if not illuminated green, check
opposite end of cable. If cable is plugged in and switch or
router shows activity indication, replace network cable.
Incorrect IP address input to
controlling computer or mobile
device browser
Check IP address on host router or using an IP scan tool.
If IP address is correct, perform full power reset of amplifier
(remove and reinsert AC inlet cord).
Turning on pre-amp does not
automatically turn on amplifier
Trigger cable missing, misfired
or plug not seated fully in
trigger in jack
Check trigger cable connections and re-test.
Trigger voltage outside
acceptable range
Refer to pre-amp information to ensure the trigger output falls
into the range 5-24Vdc.
Amplifier runs for a while then one
or more channels cut out
Faulty (shorted) loudspeaker
connection
Check loudspeaker connections at the amplifier and at the
speaker terminals. Look for frayed leads touching each other
or touching chassis metal.
Faulty loudspeaker Remove loudspeaker and re-check channel with a
known-good loudspeaker.
Amplifier runs hot even at low
audio levels
Ventillation inadequate Check to ensure that sides, rear and top of unit have at least
2 inches of air space and that air can flow in and out of
space around amplifier installation.
Low impedance
loudspeaker load
Check to ensure that the loudspeakers are greater than or
equal to 3 ohms nominal impedance.
Faulty (shorted)
loudspeaker connection
Check loudspeaker connections at the amplifier and at the
speaker terminals. Look for frayed leads touching each other
or touching chassis metal.
Faulty loudspeaker Remove loudspeaker and re-check channel with a
known-good loudspeaker.
Obtaining Additional Help
problem or symptom possible causes recommendations
16 8008 AND IRIDIUM USER GUIDE ©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
technical specifications
specification Iridium 8008
Power output 400W into 8
600W into 4
200W into 8
400W into 4
THD <0.02% (8)
<0.03% (4)
<0.015% (both channels driven, 8)
<0.03% (both channels driven, 4)
Frequency response 5Hz to 20kHz +0/-0.1dB
5Hz to 100kHz +0/-2 dB
5Hz to 20kHz +0/-0.1 dB
5Hz to 100kHz +0/-1.2 dB
Voltage Gain 28dB 28dB
Tim/dim distortion 0.01% 0.003%
Phase Inversion No No
S/N >112 dB, A-weighted >110 dB, A-weighted
Slew Rate > 240 V/µSec >120 V/uSec
Damping factor 200, 8@50Hz 400, 8@50Hz
Input sensitivity 1W: 60mV (SE & balanced)
400W: 1.2V (SE & balanced)
1W: 120mV (SE & balanced)
200W: 1.7V (SE & balanced)
Input impedance 15k(SE)
45k(bal)
46k(SE)
70k(Balanced)
Rail voltage +/- 50Vdc +/- 70Vdc
Power consumption standby: <1W
idle: 120W
max: 1500W
standby: <1W
idle: 120W
max: 1500W
ethernet/RS-232 status & control of standby/on status & control of standby/on, channel configuration
12 Volt Trigger standby/on control standby/on control
inputs gold-plated, panel-mounted RCA jacks
XLR balanced jack
gold-plated, panel-mounted RCA jacks
XLR balanced jack
outputs 2 sets gold-plated, 60-Amp insulated speaker
binding posts
2 sets gold-plated, 60-Amp insulated speaker
binding posts
Unit dimensions 7”(17.8 cm) H x 16”(40.6 cm) D x 19”(48.3 cm) W 7”(17.8 cm) x 16”(40.6 cm) x 19”(48.3 cm)
Unit weight 60 lbs (27.2kg) 63 lbs. (28.6 kg)
Finish black or silver w/ satin anodized finish black or silver w/ satin anodized finish
Shipping carton 12”(30.5 cm) x 22”(55.9 cm) x 24”(61 cm) 12”(30.5 cm) x 22”(55.9 cm) x 24”(61 cm)
Carton weight 68 lbs (30.8kg) 71 lbs. (32.2 kg)
19
8008 AND IRIDIUM USER GUIDE
©2012 Indy Audio Labs, LLC all rights reserved / Revision20130220
Document No. 1000571
WARRANTY
U.S. and Canada:
The Warranty below is valid only for sales to consumers
in the United States or Canada.
The manufacturer warrants this product to be free from defects in
materials and workmanship (subject to the terms set forth below)
for a period of five (5) years from the date of purchase. During
the Warranty period, the manufacturer will repair or replace
(at the manufacturer’s option) this product or any defective parts.
To obtain technical support and/or warranty service, you may
either: (a) contact the authorized Aragon dealer from which you
purchased this product or (b) call INDY AUDIO LABS at 1-866-559-
5113 (toll free) or (c) email INDY AUDIO LABS support at support@
indyaudiolabs.com. If you choose to call INDY AUDIO LABS directly
we strongly suggest that you choose the technical support option as
the majority of customer problems can be solved over the phone.
If technical support is unable to solve the problem, they will advise
as to whether the preferred route to obtain warranty service is to
return the product to the Authorized Aragon dealer from which
you purchased the product or to return the product directly to the
manufacturer, freight paid, for repair. If returning the product you will
need to obtain a Return Authorization from Indy Audio Labs and ship
this product in either its original packaging or packaging affording
an equal degree of protection.
Proof of purchase in the form of a bill of sale or receipted invoice
(which is evidence that this product is within the Warranty period)
must be presented or included in order to obtain Warranty service.
This Warranty is invalid if (a) the factory-applied serial number has
been altered or removed from this product or (b) this product was not
purchased from an Authorized Aragon dealer. You may call 1-866-
559-5113 (choose the INDY AUDIO LABS customer service option)
to confirm that you have an unaltered serial number and/or that you
purchased from a Authorized Aragon dealer.
This Warranty is only valid for the original purchaser and will
automatically terminate prior to expiration if this product is sold or
otherwise transferred to another party.
This Warranty does not cover cosmetic damage or damage due to
misuse, abuse, negligence, acts of God, accident, commercial use or
modification of, or to any part of, the product. This Warranty does not
cover damage due to improper operation, maintenance or installation,
or attempted repair by anyone other than the manufacturer or an
INDY AUDIO LABS dealer which is authorized to do INDY AUDIO LABS
warranty work. Any unauthorized repairs will void this Warranty. This
Warranty does not cover product sold AS IS or WITH ALL FAULTS.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS
WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER.
THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE
EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE.
Applicable Territories: Some states and foreign territories do not allow
the exclusion or limitation of incidental or consequential damages or
implied warranties so the above exclusions may not apply to you.
This Warranty gives you specific legal rights, and you may have
other rights, which vary from state to state and territory to territory.
The warranty on this product if it is sold to a consumer outside of
the United States or Canada shall comply with applicable law and
shall be the sole responsibility of the distributor that supplied this
product. To obtain any applicable warranty service, please contact
the dealer from which you purchased this product, or the distributor
that supplied this product.
This manual suits for next models
1
Table of contents
Other INDY AUDIO LABS Amplifier manuals
