Indy WAKEBOARD TOWER SPEAKERS User manual

INSTALLATION GUIDE
WAKEBOARD TOWER SPEAKERS
Design Patent US and Australia

STEP 1:
Unpack and check the contents of the box
Check the parts list and the Installation Guide corresponds with the product you purchased
Ensure you have the correct tools to complete the Installation.
Ensure you have the skills to complete the install.
Please Read all Instrustions prior to installation.
If you are NOT sure of any part of the guide or you have any questions
Please contact the supplier or Indy Wakeboard Towers direct
Email: [e-mail]
EXPLODED VIEW OF THE INDY WAKEBOARD TOWER SPEAKERS

8 x Self Stainless Steel Screws
2 x Clamp (plus rubber collars) 12 x M6 long bolts for clamp
2 x Black Indy Logo Speaker Grills
2 x Indy Speakers 2 x Aluminium Pods
PARTS LIST
Design Patent United States and Australia

STEP3: ASSEMBLE THE BALL CLAMP.
NOTE: Take one half C section and line up the holes insert the 4 x long M6 bolts.
Check that the half C section is ush around the edge with the other half of clamp.
If NOT ush remove and rotate the C section and re attach.
STEP4: ATTACHING POD TO THE WAKEBOARD TOWER
(A) Remove the speaker from the speaker casing pod. Carefully remove the grill and speaker
by removing the stainless steel screws.
NOTE: Inside the speaker casing pods you will see two M6 bolts that go through the pod into
the clamp. If the clamp is tight you can loosen these two bolts and the clamp will rotate.
(B) Remove the top half C section of the clamp.
(C) If your tower is 2.5inch no rubber collar is required. For your INDY tower use the rubber collar supplied
the thinner one of the 2 supplied. Place the collar over the top of the tube, place the half C section of the
clamp over the top. Now you can attach the speaker casing pods to the C section of the clamp.
Repeat with the other speaker.
(D) Position the tower pods in the position you like. MARK the position of the clamp. Marke in the center of
the tower tube on the underside. Drill a hole in the centre, then smooth of the rough edges.
NOTE: At this point you can run your wire harness through the tower tubes and out the holes you have
just drilled. Ready to be attached to your speaker
INSTALLATION GUIDE
Design Patent United States and Australia

STEP5: ATTACHING PODS AND DJUSTING - DIRECTION
NOTE: Inside the speaker casing pods you will see two small M6 bolts that go through to the clamp.
(A) From inside the speaker pod loosen the two M6 bolts, now you can swivel the speaker pod to
the direction you require left or right to suit the curve of you top bar of your tower.
Once you have the correct position tighten the bolts from the inside. We recommend you use
lock tight to secure the bolts nice and rm.
STEP 6: ATTACHING SPEAKER TO THE PODS
NOTE: At this stage your wires should be inserted through the clamp to the inside of the pod.
Allow enough length so you can attach to the speaker.
We recommend that you solder the wires to the speakers for the best result.
(B) After attaching the wires to the speakers you can insert the speaker into the pod, place the black
Indy Grill over the speaker and line up the holes. Ensure the logo is in the correct position so you can
read it.
WARNING: Whilst attaching speaker and speaker grill, be gentle and careful whilst inserting the screws
and tigthening. DO NOT OVER TIGTHEN as you might break the grill.
We recommend that you use a hand screw driver NOT a motorised drill for attaching the speaker and grill.
INSTALLATION GUIDE
Design Patent United States and Australia

INSTALLATION GUIDE
Design Patent United States and Australia.
WARNING:
Before and after towing behind vehicle check all bolts of the speakers and pods.
Before using you boat check the products bolts and screws and the speakers are secure and operating
Do not amp the speakers more than 60 watts per channel to a sepaker
Do not run the BASS high through the speakers, these are not sub woofers
Ensure the correct gauge wires are used when installing the speakers.
Care and maintain your products. Clean and rinse oand dry.
Use a marine clear protection spray on the bolts for best maintance.
WARRANTY
Indy warrants the product (not including other 3rd party accessories) against manufactures defects.
Lifetime for the Alloy Clamps, pods. 12 months for the speakers.
To claim you must contact Indy or its Distributor. The product/part is to be sent to the Distributor
for inspection where it will either be repaired or replaced. (unless otherwise agreed in writing)
The customer is liable for costs associated in shipping the product/part to Indy.
Indy is not responsible for personal injury or damage to the boat caused by the use wakeboard
rtower speakers or any transport charges or cost of installation or removal of the wakeboard tower speakers
Indy is not liablity for direct or indirect or consequential damages resulting from delay or improper
installation.
Warranty does NOT cover Anodised, polished,powder coated surfaces as well as any hardware
corrosion, rubber inserts. They are specically excluded as their care and use can not
be controlled by Indy. Please contact Indy for replacment rubbers.
No dealer, retailer or manufacturer is the agent of James G Pty Ltd and may not assume any liablity in
connection with this warranty. This warranty is in lieu of all.