Infinite Peripherals Linea Pro 7 Plus User manual

Linea Pro® 7 Plus
User Manual
For iPhone® 7 Plus / 8 Plus Mobile Devices

LINEA PRO 7 PLUS USER MANUAL
2
Table of Contents
Contacts 3
Legal Notice 3
Compatible Devices 3
Overview 4
Linea Pro 7 Plus Features 4
Getting Started 4
Technical Specifications 5
Before Using Linea Pro 7 Plus 6
Linea Pro 7 Plus Accessories 6
Developing Applications 6
Box contents 6
Linea Pro 7 Plus Layout 7
Assemble Your Linea Pro 7 Plus 8
Charge the Battery 9
Check Battery Status 9
Replace the Battery 9
Power On Linea Pro 7 Plus 10
Scan Barcodes 10
Read Contactless Cards (Optional) 10
Troubleshooting 11
Update Software 11
Warranty 11
Disclaimer 11
Product Returns and Servicing 12
Symbols 12
Federal Communications Commissions 13

LINEA PRO 7 PLUS USER MANUAL
3
Compatible Devices
Legal Notice
“Made for iPhone” (MFi) means an electronic accessory is designed
to connect specifically to the iPhone and has been certified by the
developer to meet Apple performance standards. Apple is not
responsible for the operation of this device or its compliance with safety
and regulatory standards.
Note
The use of this accessory with an iPhone may affect wireless
performance.
iPad, iPhone and iPod touch are trademarks of Apple Inc., registered in
the U.S. and other countries. Lightning™ is a trademark of Apple Inc.
Made for these mobile digital devices:
• iPhone 7 Plus
• iPhone 8 Plus
Mobility Sales/ Technical Support Center
Infinite Peripherals, Inc.
17681 Mitchell N
Irvine, CA 92614-1605
Toll-Free 866.278.7860
Office 949.222.0300
Website ipcmobile.com
Headquarters/ Main Warehouse
Infinite Peripherals, Inc.
2312 Touhy Avenue
Elk Grove Village, IL 60007-5329
Toll-Free 800.278.7860
Office 847. 818.1260
Fax [phone]
Contacts

LINEA PRO 7 PLUS USER MANUAL
4
Overview
The hand-held Linea Pro 7 Plus is a reliable 1D/2D barcode scanner
designed to fit the iPhone 7 Plus and iPhone 8 Plus. With a hot-
swappable battery and integrated hand-strap for increased mobility,
you can integrate with your existing systems using Bluetooth® Plus the
intuitive Software Development Kit (SDK).
Linea Pro 7 Plus Features
The Linea Pro 7 Plus allows mobile employees to convert their iPhones
into a powerful solution for the retail, warehousing, supply chain,
ticketing, and hospitality industries. The Linea Pro 7 Plus includes an
optional 1D or 2D barcode scanner, Bluetooth® and RFID.
Note
Use of the barcode scanner or contactless card reader requires the
installation of special software. Contact your Infinite Peripherals
account representative for compatible third-party software solutions.
Feature Description
2D Barcode
Imager
One-dimensional and two-dimensional barcode
scanner, which can be read omni-directionally.
Contactless
card reader
Built-in tag/card reader with read/write capability at
13.56 MHz. Reader incorporates many RFID formats,
depending on the model of your Linea Pro 7 Plus.
Bluetooth
compatible
Bluetooth 2.0 SPP compatibility for a Bluetooth
peripheral such as a printer.
Syncing Enables your iOS device to be synced with iTunes.
Battery
status
View the battery status in the application on the iOS
device.
Getting Started
Linea Pro 7 Plus scans barcodes and passes that data into compatible
iOS applications. To get you up and running with your new Linea Pro 7
Plus, review these sections.
Note
Observe any notes, cautions, or warnings throughout this guide for
additional information, special care required, or important points to
prevent injury or adverse affects.
What to do Why important Section
Connect LP
7 Plus with
your iOS
device
Connect unit and
iOS device prior to
first use
Assemble Your
Linea Pro 7 Plus
Charge LP7 Plus Ensures battery is fully
charged before first use
Charge the Battery
Turn on the LP7
Plus
Initialize the barcode
scanner and /or
contactless card (RFID)
functions
Power On Linea Pro
7 Plus

LINEA PRO 7 PLUS USER MANUAL
5
Electrical
1D/2D Barcode Scanner
1D: EAN/UPC, GS1 Databar (limited expanded & omni-directional),
RSS, Code 39, Code128, UCC/EAN 128, ISBN, ISBT, Interleaved/Matrix/
Industrial and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI,
Plessey, Telepen, postal codes (Australian Post, BPO, Canada Post, Dutch
Post, Japan Post, PostNet, Sweden Post)
2D: Data Matrix, PDF417, Micro PDF 417,
Codablock, Maxicode, QR, Aztec, GS1 composite codes,
Direct Part Marking Reading multicodes and barcodes
on mobile phone screens available.
2D Barcode Reader
• 2D Intermec EA30/ED40* CMOS Imager 752 x 480 pixels
• 2D Newland EM3396 CMOS Imager 752 x 480 pixels, laser
aimer
Battery Capacity
• Rechargeable Li-ion Battery 3.7V /2400 mAh
• Precise battery management by Fuel Gauge microcontroller for
remaining battery capacity
Power Supply
• DC 5V through USB Type-C
• DC 5V through charging station
• DC 5V through dual charging station
Indicators
Audio via electromagnetic buzzer
(Optional) Contactless Card Reader
• ISO/IEC 14443 Type-A/MIFARE:
* MIFARE MINI
* MIFARE CLASSIC-1K, MIFARE CLASSIC-4K
* MIFARE ULTRALIGHT, ULTRALIGHT-C
* MIFARE PLUS 2K/4K
* MIFARE DESFire card
• Supports most contactless card cards/tags:
* ISO/IEC 14443 Type - B
* ISO 15693
Technical Specifications
Mechanical
Compatibility
iPhone 7 Plus
iPhone 8 Plus
Dimensions
93.5mm x 36.5mm x 186.5mm (3.68” x 1.44” x 7.34”)
Weight
250g (8.82oz.) without iOS device
Connectivity
• Apple 9 pin connector
• Pass-through sync through USB Type-C
• Bluetooth 2.0 Class 2
• SPP - Serial Port Prole
Buttons
• Two scan buttons
• Reset device button
Port
USB Type-C for iOS device charge and sync
Processor
32-bit ARM Cortex - M3 MCU
Environment
Operating Temperature
-10° to +40°C / 14°F to +104°F
Storage Temperature
-20° to +50°C / -4°F to +122°F
Relative Humidity
5% to 90%
General Certifications
CE
Note:
Use only UL approved USB adapters with a minimum of 5V/2.1A
Charging current for the iOS device is selected from the application:
• 500mA (default)
• 100mA

LINEA PRO 7 PLUS USER MANUAL
6
Box contents
Your Linea Pro 7 Plus ships with these items:
USB Type-C/Sync Cable
Note:
Bulk shipments may ship without
cables in each box.
Linea Pro 7 Plus (1)
Standard Battery (1)
T8 Torx screws (4)
Before Using Linea Pro 7 Plus
• Remove the device and any included accessories from the
shipping carton and verify contents against your packing list.
• Retain all packing materials, invoice, and bill of lading. These may
be required to return the device for servicing later, or to process
a claim with the shipping carrier.
• Carefully inspect the contents inside of the packaging for any
signs of damage.
• If there are signs of damage, do not attempt to use the unit.
Notify your account executive or contact Innite Peripherals
technical support, https://ipcmobile.com/support.
• Ensure the battery is fully charged.
• If the battery is fully discharged, the charging time is
approximately 3 hours and 30 minutes.
Linea Pro 7 Plus Accessories
Contact your Infinite Peripherals account representative for information
about current and future product accessory offerings.
Developing Applications
Software Developers Kit
Software is not automatically provided with your Linea Pro 7 Plus.
Integrating the Linea Pro 7 Plus into your iOS application requires the
use of the Infinite Peripherals Universal SDK. The SDK incorporates
an API specifically for developing applications to use Linea Pro 7 Plus
functionality.
For additional details on using the Infinite Peripheral Universal SDK,
please refer to the appropriate SDK documentation. You can contact
your Infinite Peripherals account representative for Third-Party software
solutions.
For the latest Infinite Peripheral Universal SDK please visit our
developer portal:
View Latest SDK →
developer.ipcmobile.com/

LINEA PRO 7 PLUS USER MANUAL
7
Linea Pro 7 Plus Layout
1. Barcode Engine
2. LED Battery Status Indicator
3. On/Off Button for iOS device
4. Battery Cover
5. Left/Right Scan Buttons
6. Opening for Strap
7. Volume Button on iOS device
8. Charging pads
9. Reset Button for unit
10. USB Type-C Connector
11. Screws to Remove Front Cover

LINEA PRO 7 PLUS USER MANUAL
8
Assemble Your Linea Pro 7
Plus
Before attaching your iOS device with the Linea Pro 7 Plus, you will need
a 3/8 flat-head screwdriver to remove the bottom two latches and the
top cover.
Note:
Torque required is 4.6-6 pound-inch.
Remove Top Cover
1. To remove the top cover, unscrew the four T8 Torx screws.
2. Using the at-head screwdriver, pop out the top cover from the
rst two latches to remove it.
Note:
The top cover is easily removed because the latches are
loosened when the rst four screws were removed.
3. For the remaining latches, slide the cover forward instead of
pulling the top up. The Linea Pro 7 Plus top cover is removed.
Attach iOS Device
1. Attach the iOS device to the Lightning™ connector by rmly
sliding it into place.
2. Align the front cover with the two hooks, and then slide it
down by pressing gently back into place.
3. Tighten all four screws on the back cover to further secure the
top cover.

LINEA PRO 7 PLUS USER MANUAL
9
Charge the Battery
The Linea Pro 7 Plus uses a Lithium Ion rechargeable battery.
Before first use ensure the battery is fully charged. Charging time is
approximately 3 hours and 30 minutes, if fully discharged.
The Linea Pro 7 Plus supports pass-through charging to the iOS device.
The unit and iOS device may be charged together using the USB Type-C
port or by the charging pads.
To charge the battery, connect the USB-Type C charger cable to the USB
port.
Important
Prevent electrical damage to the unit and/or battery, use only the
approved USB Type-C charger cable.
Check Battery Status
Four LEDs indicate the battery status.
LED Color Description
Battery level is below 19%
Battery level is above 20%
Battery is charging via attachment to outside
power from USB connector or charging pads
No color Linea Pro 7 Plus power is turned off
Replace the Battery
Replace the Linea Pro 7 Plus battery only with a new, original battery
(part number, PL-15-110).
1. To replace the rechargeable battery, slide the battery pawl
down, and then pull up the battery cover.
2. Pull up the old battery to remove it.
3. Insert the side of the battery with the contacting pads, and then
press gently downward.
4. Press the battery pawl down, and then close the battery cover.

LINEA PRO 7 PLUS USER MANUAL
10
Power On Linea Pro 7 Plus
After the iOS device is attached to the Linea Pro 7 Plus and the
application software is installed, you can turn on the unit.
1. With the unit turned off, press one of the Scan buttons on the
side of the unit. When the unit is active, the LED on the top side
illuminates blue, based on the battery level.
2. Unlock the iOS device screen.
Note
When the Linea Pro 7 Plus is left idling for an extended period, the
power is automatically turned off to preserve the charge on the internal
battery pack. If turned off, the unit is in sleep mode immediately.
Scan Barcodes
The scan engine in the Linea Pro 7 Plus 1D model supports one-
dimensional (1D) barcode symbols. The 2D model scan engine
supports one-dimensional (1D) and two-dimensional (2D) barcode
symbols. The effective reading distance of the barcode reader varies
based on the barcode size. For example, 15-20 cm (5.9-7.9 inches).
These types of scanning modes are supported:
• Single scan
• Multi-scan
• Motion detect
• Multi-scan without duplicates
To scan a barcode
1. Press and hold the Scan button on either side of the unit to
activate the Linea Pro 7 Plus.
2. Position the scan head as close to the center of the barcode
label by aiming the illumination box over the outer edges of
the barcode.
3. Pull the unit back slowly back or forth, increasing the distance
between the barcode and scan head, until the barcode is read
by the scanner. Data is displayed on the iOS device.
Read Contactless Cards
(Optional)
The contactless card reader incorporates several RFID formats
depending on your Linea Pro 7 Plus model.
To use the contactless card reader
1. Press the Scan button to activate the unit.
2. Place the RFID tag/card over the receiver/transmitter as
indicated by the RFID label.
Note
Data is sent from the Linea Pro 7 Plus contactless card reader to the
iOS device.

LINEA PRO 7 PLUS USER MANUAL
11
Troubleshooting
Barcode Scanning and Contactless Card Reading
If the Linea Pro 7 Plus is not scanning barcodes properly or not reading
RFID cards tags, refer to these possible causes and resolutions.
Note
If problems persist and not resolved by the resolutions indicated,
contact technical support.
Issue Resolution
Barcode scanner
or RFID reader
does not power
on
• Linea Pro 7 Plus battery is too low
• Linea Pro 7 Plus is not turned on by the
software
• Faulty scan engine
Barcode or
RFID card data
not returned or
partially returned
during scanning/
reading
• Unreadable barcode or tag/card
• Battery is too low
• Faulty scanning or reader
• Software decoding incorrectly
Multi-scanning
not working
• Multi-scan mode is not enabled
• Software does not support multi-scan
Unable to read
barcode or RFID
card/tag
• Barcode type or RFID type are not
enabled or supported
• See Technical Data for more information
Warranty
Infinite Peripherals does not warrant, and is not responsible for, any
damage to the Linea Pro 7 Plus (“Product”) or the assembled iOS
device as a result of liquid or solid particle intrusion into the Product,
or damaged caused by dropping the Product with the assembled iOS
device. If a material or workmanship defect arises with regard to any
Infinite Peripherals product, and a valid claim is received within the
Warranty Period, Infinite Peripherals (at our sole discretion) will repair
the Product using new or refurbished parts, or replace the Product with
a new or refurbished Product.
For purposes of this limited warranty, “refurbished” means a product or
part that has been substantially returned to its original specifications. In
the event of a defect, these are your exclusive remedies.
Disclaimer
NO WARRANTY. This technical documentation is provided AS-IS. Further,
the documentation does not represent a commitment on the part of.
Infinite Peripherals, Inc does not warrant that it is accurate, complete
or error free. Any use of the technical documentation is at the risk of
the user. Infinite Peripherals, Inc reserves the right to make changes
in specifications and other information contained in this document
without prior notice, and the reader should in all cases consult Infinite
Peripherals, Inc to determine whether any such changes have been
made. Infinite Peripherals, Inc shall not be liable for technical or
editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from the furnishing, performance,
or use of this material. Infinite Peripherals, Inc does not assume any
product liability arising out of or in connection with the application or
use of any product or application described herein.
Update Software
1. To update the software with a newer version from the
application, tap Update Firmware.
2. Tap Update.
3. To update the barcode engine with a newer version, tap
Update Barcode Engine Firmware. The current rmware
version and the new rmware version are displayed.
4. Tap Update.

LINEA PRO 7 PLUS USER MANUAL
12
Product Returns and
Servicing
Use the link in step 1 to create an account and gain access to our
Knowledge Base and online support services. Through our online
support center, you’ll be able to download files, open a Support Ticket,
manage your RMAs, view your account Profile and subscribe to Alerts.
To request a RMA
1. Create a user account in the RMA Support Portal at http://
ipcmobile.com/support/rma/
2. Login to your user account, and then click Create RMA Request.
3. Read the instructions provided and complete the online request
form.
4. Note the assigned RMA number and write it clearly on your
shipping carton.
5. Ship your equipment back to us using the address provided.
Symbols
Symbol Description
Refer to the instructions before using.
Manufacturer
Manufacture Date
Caution
Serial Number
P/N Part Number
Waste Electrical and Electric Equipment
Complies with part 15 of the FCC rules
Near-field communication (NFC)

LINEA PRO 7 PLUS USER MANUAL
13
Federal Communications Commissions
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the
equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions
for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.