Infinity iW-340 RDM User manual

Infinity iW-340 RDM V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 41525
MANUAL
ENGLISH

1
Ordercode: 41525
Infinity iW-340 RDM
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................6
Claims..............................................................................................................................................................................6
Description of the device.................................................................................................................................................7
Optional accessories....................................................................................................................................................7
Overview ........................................................................................................................................................................8
Backside .........................................................................................................................................................................9
Installation...........................................................................................................................................................................9
Set Up and Operation .......................................................................................................................................................9
Control Modes.............................................................................................................................................................10
One Infinity (Built-in Programs)...............................................................................................................................10
Multiple Infinitys (Master/Slave control)...............................................................................................................10
Multiple Infinitys (DMX Control) .............................................................................................................................11
Multiple Infinitys (ArtNet control)...........................................................................................................................12
Connecting to a Network .........................................................................................................................................13
ArtNet settings ..........................................................................................................................................................13
How to make a data cable...................................................................................................................................13
Fixture Linking...............................................................................................................................................................14
Data Cabling...............................................................................................................................................................14
Control Panel ...............................................................................................................................................................15
Control Mode ..............................................................................................................................................................15
DMX Addressing ..........................................................................................................................................................15
Menu Overview...........................................................................................................................................................16
Main Menu Options....................................................................................................................................................17
1. DMX Address ........................................................................................................................................................17
2. Edit Mode..............................................................................................................................................................18
3. Settings Menu .......................................................................................................................................................19
3.1 Performance ......................................................................................................................................................20
3.2 Service .................................................................................................................................................................22
4. Built-in Programs...................................................................................................................................................24
5. Test Menu ..............................................................................................................................................................24
6. Information Menu ................................................................................................................................................25
DMX Channels .............................................................................................................................................................26
21 Channels ..............................................................................................................................................................26
28 Channels ..............................................................................................................................................................29
27 Channels ..............................................................................................................................................................33
15 Channels + 12 channels (DMX + Artnet)........................................................................................................37
Channel settings .........................................................................................................................................................40
Maintenance....................................................................................................................................................................41
Replacing a Fuse ........................................................................................................................................................41
Troubleshooting ...............................................................................................................................................................42
No Light.........................................................................................................................................................................42
No Response to DMX..................................................................................................................................................42
Product Specifications....................................................................................................................................................44
Dimensions........................................................................................................................................................................45
Notes ..................................................................................................................................................................................46

2
Ordercode: 41525
Infinity iW-340 RDM
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Infinity iW-340 RDM with PowerCON True 1 power cable (1,4 m)
1 bracket for truss mounting
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving your lifespan expectancy is of a higher priority, place care in providing
for lower operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.

3
Ordercode: 41525
Infinity iW-340 RDM
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always
hold the fixture at the transport handles.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmer pack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If the lens is obviously damaged, it has to be replaced, so that its functions are not impaired due to
cracks or deep scratches.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Infinity device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Infinity dealer for service.
For adult use only. Moving head must be installed out of the reach of children. Never leave the unit
running unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Infinity. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.

4
Ordercode: 41525
Infinity iW-340 RDM
Operating Determinations
This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
The minimum distance between light-output and the illuminated surface must be more than 1 meter.
To eliminate wear and improve lifespan, during periods of non-use, completely disconnect from
power via breaker or by unplugging.
The maximum ambient temperature ta = 40°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
If the Infinity is lowered from the ceiling or high joists, professional trussing systems have to be used.
Use a clamp to mount the Infinity, with the mounting-bracket, to the trussing system.
The Infinity must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety-cable.
When rigging, derigging or servicing the Infinity, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
The Infinity can be placed on a flat stage floor or mounted to any kind of truss with a clamp.

5
Ordercode: 41525
Infinity iW-340 RDM
Mounting a clamp to the underside of the Infinity moving head
Improper installation can cause serious injuries and/or damage of property !
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
FASE
N
BLUE
BLACK
SILVER
NULL
YELLOW/GREEN
GREEN
GREEN
EARTH
Make sure that the device is always connected properly to the earth!

6
Ordercode: 41525
Infinity iW-340 RDM
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause of the
return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

7
Ordercode: 41525
Infinity iW-340 RDM
Description of the device
Features
The Infinity iW-340 RDM is a wash moving head with high output and great effects.
Input voltage: 100-240V AC, 50/60Hz
Power consumption: 145W
Light source: 3 x 40W RGBW 4-in-1 Osram Ostar LED
Light output: 14400 Lux @ 3m
Beam angle: 4,5°-36°
Dimmer: 0-100%
Strobe: 0-20Hz
Dimmer curves: Linear, Square, I-Square, S curve
Dimmer speed: Smooth, Fast
Channel modes: 21, 27, 28 channels
Onboard: Battery powered full color display including gravity sensor
DMX-control: via standard DMX/Artnet/RDM controller
2 selectable built-in programs
Reverse pan/tilt movement
Special: pan/tilt movement, blackout
Pan 0º-540º
Tilt 0º-270º
Pan/Tilt resolution: 16 bit
Control: DMX-512, Master/Slave, Built-in Programs
Housing: Metal & flame-retardant plastic
Color: Black
Connections: 3-pin XLR data IN/OUT
5-pin XLR data IN/OUT
RJ-45 Data IN/OUT
Neutrik PowerCON True 1 IN/OUT
Fuse: T2,5AL/250V
Dimensions: 250 x 190 x 350 mm (LxWxH)
Weight: 7,2 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
MOD41525 –Wireless DMX upgrade kit
The Wireless DMX upgrade kit should be installed ONLY by a qualified technician.
Do not attempt installation yourself!

8
Ordercode: 41525
Infinity iW-340 RDM
Overview
Fig. 01
01) 3 x 40W RGBW 4-in-1 Osram Ostar LED
02) Control buttons + LCD display
Beam angle 4,5°-Electronic adjustment
Beam angle 36°- Electronic adjustment
Fig. 02

9
Ordercode: 41525
Infinity iW-340 RDM
Backside
Fig. 03
03) RJ45 connector data IN/OUT
04) Fuse T2,5AL/250V
05) Neutrik PowerCON True 1 IN
06) Neutrik PowerCON True 1 OUT
07) 3-pin DMX signal connector IN
08) 3-pin DMX signal connector OUT
09) 5-pin DMX signal connector OUT
10) 5-pin DMX signal connector IN
Installation
Remove all packing materials from the Infinity iW-340 RDM. Check that all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.

10
Ordercode: 41525
Infinity iW-340 RDM
Control Modes
There are 4 modes:
Stand-alone (built-in programs)
Master/Slave
DMX512 (21CH, 27CH, 28CH)
Artnet+DMX (15CH+12CH)
One Infinity (Built-in Programs)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Infinity is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see page 23 for more information about the built-in programs.
Multiple Infinitys (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Infinity.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
05) Link the units as shown in fig. 04. Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can
use the same functions on the master device as described on page 23 (Built-in Programs). This means
that you can set your desired operation mode on the master device and all slave devices will react
the same as the master device.
Multiple Infinitys (Master/Slave control)
Fig. 04

11
Ordercode: 41525
Infinity iW-340 RDM
Multiple Infinitys (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Infinitys and other devices.
05) Link the units as shown in fig. 05. Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's PowerCON True 1 socket,
then plug the other end of the mains power cord into proper electric power supply sockets, starting
with the first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Infinitys DMX Set Up
Fig. 05
Note: Link all cables before connecting electric power

12
Ordercode: 41525
Infinity iW-340 RDM
Multiple Infinitys (ArtNet control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a CAT-5/CAT-6 cable to connect your ArtNet controller to a network switch as shown in fig. 06.
04) Link all the Infinitys by connecting their RJ45 sockets to your network switch, using a CAT-5/CAT-6
signal cable as shown in fig. 06.
05) Supply electric power: Plug electric mains power cords into each unit's PowerCON True 1 socket,
then plug the other end of the mains power cord into proper electric power supply sockets, starting
with the first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Infinitys ArtNet Set Up
Fig. 06
Note : Link all cables before connecting electric power

13
Ordercode: 41525
Infinity iW-340 RDM
Connecting to a Network
ArtNet settings
01) Install any ArtNet-based software on your PC (Windows, Mac or user console with ArtNet support).
02) Connect the power supply to the Infinity.
03) Connect the device’s Ethernet connector (03) to your software/light controller’s Ethernet connector,
using a CAT-5/CAT-6 cable.
04) Set the IP address of your software/light controller to 2.x.x.x or 10.x.x.x, depending on the ArtNet
settings.
05) Set the subnet mask to 255.0.0.0. on both –the Infinity and your software/light controller. Make sure
that all the fixtures in the network have a unique IP address.
06) If you want to connect more than one fixture, follow the example below.
Example:
01) Make sure that each connected Infinity has a unique IP address.
02) Make sure that the subnet mask on each device is set to 255.0.0.0.
03) Set the universe of the first Infinity to 1.
04) Set the first Infinity’s DMX address to 001.
05) If you have reached the DMX limit of 512 channels, while connecting multiple Infinitys, set the
universe of the following Infinity to 2 and its DMX address to 001.
06) Repeat step 5 up to 255 times (as there are 255 universes available).
07) Using your software, map all the connected devices, using the settings described above.
08) The Infinitys are now ready for use.
09) When creating large setups, it is recommended to use a 16-bit, high speed ethernet switch to
distribute the ArtNet data signal.
How to make a data cable
A standard ETHERNET Cable can be used to replace the Data Cable required to transmit the data for the
iW-340 RDM.
Please follow the instructions below in order to create an extra Net Cable.
Take a standard net cable (CAT-5/ 5E /6) and connect it to the RJ45 connector, as shown in the picture
below (fig. 07). The wires should now be colored as follows:
Fig. 07

14
Ordercode: 41525
Infinity iW-340 RDM
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX
optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link @120V: 8 fixtures
Maximum recommended number of fixtures on a power link @230V: 16 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
•DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
The Infinity iW-340 RDM can be operated with a controller in control mode or without the controller in
stand-alone mode.

15
Ordercode: 41525
Infinity iW-340 RDM
Control Panel
A)
B)
C)
D)
E)
F)
G)
H)
I)
J)
K)
Home button
Edit Menu button
Settings Mode button
Address Setting button
Infinity Logo button/ Previous screen
Up button
Down button
OK/ENTER
Left button
Right button
LCD display
Fig. 08
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Infinity will respond to the controller.
Please note when you use the controller, the unit has 28 channels.
When using multiple Infinitys, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Infinity should be 1(001); the DMX address of the second Infinity
should be 1+28=29 (029); the DMX address of the third Infinity should be 29+28=57 (057), etc.
Please, be sure that you do not have any overlapping channels in order to control each Infinity correctly.
If two or more Infinitys are addressed similarly, they will work similarly.
For address settings, please refer to the instructions under ”Addressing”.
Controlling:
After having addressed all Infinity fixtures, you may now start operating these via your lighting controller.
Note: After switching on, the Infinity will automatically detect whether DMX 512 data is received or not. If
not the problem may be:
The XLR cable from the controller is not connected with the input of the Infinity.
The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It’s necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 30 seconds
When no button is pressed for 30 seconds, the display will turn off.
To light up the display, you have to press any of the buttons on the control panel.
Once you have pressed the button, the display will light up.

16
Ordercode: 41525
Infinity iW-340 RDM
Menu Overview

17
Ordercode: 41525
Infinity iW-340 RDM
Main Menu Options
DMX address
Edit Mode
Settings Menu
Built-in Programs
Test Mode
Info
Home
Up
Edit Menu
Down
Settings Mode
OK/Enter
Address Setting
Left
Previous screen/Infinity Logo
Right
1. DMX Address
With this menu you can set the DMX address.
01) Press the button.
02) Press the button, to confirm. You can choose 512 different DMX addresses.
03) Press the buttons to select the required address from .
04) Once you have set the desired DMX address, press the button to store your DMX address.

18
Ordercode: 41525
Infinity iW-340 RDM
2. Edit Mode
With this menu you can set your desired DMX personality and running mode.
01) Press the button and select .
02) Press the button, to confirm. You can choose between 2 submenus.
03) Press the buttons to select the required mode.
04) Press the button, to confirm.
05) If you have chosen PERSONALITY you can set the desired DMX channels.
06) Press the buttons to select the desired DMX channels.
07) Press the button, to confirm.
08) Once you have selected the desired DMX channels, press the buttons to change the
value from NO to YES.
09) Once you have selected the desired setting, press the button to store your settings.

19
Ordercode: 41525
Infinity iW-340 RDM
10) If you have chosen RUN MODE you can choose the desired operation mode.
11) Press the buttons to select the desired operation mode.
12) Press the button, to confirm.
13) Once you have selected the desired operation mode, press the buttons to change the
value from NO to YES.
14) Once you have selected the desired setting, press the button to store your settings.
15) If you choose NO in MASTER MODE the device will react as slave, it will react the same as its master
device.
16) If you choose YES in MASTER MODE the device will react as the master, all other devices will react as
a slave device.
3. Settings Menu
With this menu you can set your desired settings.
01) Press the button and select .
02) Press the button, to confirm. You can choose between 2 submenus.
03) Press the buttons to select the required settings submenu.
04) Press the button, to confirm.