Infinity PRELUDE MTS-STAND User manual

© 1999 Infinity Systems, Inc.,250 Crossways Park Drive,Woodbury, NY 11797 USA [phone] (USAOnly) www.infinitysystems.com
Infinity is a registered trademark of Infinity Systems, Inc.Printed in USA 11/99 Part No.PREMTSSTAND
InstallationGuide
FloorStandforPreludeMTS Tower
PRELUDE™MTS-STAND

3
PRELUDEMTS-STAND
2PRELUDEMTS-STAND
InstallingtheTowerontotheFloorStand
–When using the tower as a surround speaker,
setToggle Switch in tower cup to “Full Range.”When using as
a front channel,set Toggle Switch in tower cup in bottom to
the “Full Range”position.Please consult the Prelude MTS
Subwoofer manual for exceptions to this setting.
STEP 1– Insert double-ended Audio Banana Plug into tower
as shown.
STEP 3
– Screw alignment pins into cup in bottom of tower.
Use two per tower.Screw threaded ends into holes and tighten
until snug.DO NOT overtighten.
–To add greater stability to the tower stand,add
sand (not included) in the plastic bag provided in the tower base.
Turn the base upside-down and remove the (3) 1/4-20 Phillips
screws holding the foot onto the base.
STEP 4
– Remove one foam pad,pull out the plastic bag and open
it.Place it back into the opening of the base,taking care to fold it over
the sides so as to keep sand from falling into the base.Fill theplastic
bag with sand.
STEP 5
STEP 2– Seal the plastic bag,making sure to tuck it back
inside the base and place the previously removed foam pad on
top of the sealed bag.Replace the foot with the same 1/4-20
Phillips screws.
STEP 6
–Turn stand over and slowly lower the tower
assembly onto the stand,being careful to insert the alignment
pins into their receptacle guide holes.
STEP 7
– Fasten the four
10-32 Socket Head Screws
through the tower base as
shown;two through the front
baffle and two in the rear slot.
Press flush into place two
screw caps to hide holes in
front-baffle base. Make sure
that the alignment slots point
toward the center to ensure that
the surface curve matches that
of the baffle.
STEP 8

3
PRELUDEMTS-STAND
2PRELUDEMTS-STAND
InstallingtheTowerontotheFloorStand
–When using the tower as a surround speaker,
setToggle Switch in tower cup to “Full Range.”When using as
a front channel,set Toggle Switch in tower cup in bottom to
the “Full Range”position.Please consult the Prelude MTS
Subwoofer manual for exceptions to this setting.
STEP 1– Insert double-ended Audio Banana Plug into tower
as shown.
STEP 3
– Screw alignment pins into cup in bottom of tower.
Use two per tower.Screw threaded ends into holes and tighten
until snug.DO NOT overtighten.
–To add greater stability to the tower stand,add
sand (not included) in the plastic bag provided in the tower base.
Turn the base upside-down and remove the (3) 1/4-20 Phillips
screws holding the foot onto the base.
STEP 4
– Remove one foam pad,pull out the plastic bag and open
it.Place it back into the opening of the base,taking care to fold it over
the sides so as to keep sand from falling into the base.Fill theplastic
bag with sand.
STEP 5
STEP 2– Seal the plastic bag,making sure to tuck it back
inside the base and place the previously removed foam pad on
top of the sealed bag.Replace the foot with the same 1/4-20
Phillips screws.
STEP 6
–Turn stand over and slowly lower the tower
assembly onto the stand,being careful to insert the alignment
pins into their receptacle guide holes.
STEP 7
– Fasten the four
10-32 Socket Head Screws
through the tower base as
shown;two through the front
baffle and two in the rear slot.
Press flush into place two
screw caps to hide holes in
front-baffle base. Make sure
that the alignment slots point
toward the center to ensure that
the surface curve matches that
of the baffle.
STEP 8

© 1999 Infinity Systems, Inc.,250 Crossways Park Drive,Woodbury, NY 11797 USA [phone] (USAOnly) www.infinitysystems.com
Infinity is a registered trademark of Infinity Systems, Inc.Printed in USA 11/99 Part No.PREMTSSTAND
InstallationGuide
FloorStandforPreludeMTS Tower
PRELUDE™MTS-STAND