iNFinuvo Hovo 700 series User manual

MULTI-FUNCTION ROBOTIC VACUUM CLEANER
Model NO.: Hovo 700 Series
USER MANUAL
®

Table of Contents
Table of Contents·······················································01
Safety Instructions······················································02
Product Features····················································03-04
Product Accessories and Anatomy
Main Unit and Accessories··············································05
Anatomy of the Main Unit···············································06
Unit Display Panel·······················································07
Installing the Battery·····················································08
Product Operations and Settings
Auto Charging Dock Station············································09
Remote Control························································10
UV Lamp and Water Seeping Speed Settings······························11
Clock and Cleaning Schedule Settings····································12
Virtual Blocker Settings·················································13
Product Maintenance
Installing/Removing/Cleaning the Dust Bin································14
Removing the Roller Brush··············································15
Installing the Roller Brush···············································16
Installing/Removing the Suction Inlet·····································17
Installing the Trailing Bar, Mop, and Water Tank···························18
Error Codes and Troubleshooting··········································19
Technical Specifications·················································20

Before using this product, please read the following safety instructions
and follow all routine safety precautions!
Please read these instructions carefully.
Please store this manual properly.
Any operation not in compliance with this manual is likely to cause damage to the product.
Warning

Product Features
Two-way virtual blocker
The virtual blocker creates an invisible barrier that the cleaner will not cross. This can
confine the cleaner to a particular room or area.
The cleaner can control the water seeping speed of the water tank automatically. You can
select the water seeping speed through the remote control to achieve the optimal uniform
wet mopping effect. While charging, water seeping will be shut automatically to prevent
water leakage.
Intelligent voice prompts for power-on, malfunction, full dust bin, mis-operation, water tank
empty, etc.
Each package includes two dust bins: one large capacity dust bin (0.9L ) used for normal
vacuum cleaning, and a regular capacity dust bin (0.6L) combined with one small dust bin
(0.2L) used for vacuuming & wet mopping.
3D UV kills bacteria on floors, the suction inlet, and inside of the dust bin.
Patent V-shaped brush made of soft wool suitable for tiles, marble, and wood floors. Also
includes a rear brush made of rubber suitable for carpet deep cleaning.
The 3D conditioning level filter (effectively preventing clogging when the dustbin is close to
full) + HEPA filter prevent secondary air pollution. The dust bin and 3D filter can be
washed directly.
Multi-function double dust bin

The cleaner can swap between suction (mainly used for long carpet to avoid getting
tangled) and sweeping according to floor conditions. Refer to page 15-17 for details on
swapping between suction and sweeping.
Product Features
The suction power of the cleaner is up to 40W and can even pick up fine dust.
When detecting lots of dirt, the cleaner will adjust the suction power automatically, which
greatly improves the cleaning efficiency and also saves as much as 30% on electricity.
When detecting garbage, the cleaner will automatically increase suction power. When the
dust bin is full, the cleaner will give a voice prompt and light up the “ ” icon on the
display panel.
Regardless of elders or children, a simple touch on the “ ” icon and the cleaner will run
automatically.
Super wide wheel avoids slipping when the cleaner is wet mopping.
Super wide off-road wheel design

Product Anatomy and Accessories
This product is for home use only and can clean a variety of household floors including: short
carpets, wood, and ceramic tile, etc.
Virtual Blocker x 1
Trailing Bar x 1
(Hovo 780 only) Mop x 2
(Hovo 780 only)
Suction Inlet x 1
(Hovo 780 only) User Manual x 1
Main Unit and Accessories
HEPA Filter x 1
Side Brush x 4
(Please fix two on the cleaner before use)
Small Dust Bin x 1
(Please assemble with
water tank before use,
see Page 18)
Water Tank x 1
Cleaning Brush x 1
(Mounted on the Dust Bin)
The unit works on a rechargeable lithium-ion battery and microcomputer control. It is an
intelligent vacuum cleaner that features UV sterilization, various automatic cleaning modes,
vacuuming, wet mopping, scheduled cleaning, remote control, and automatic recharging.

Top View
Bottom View
Dustbin cover
Exhaust outlet
Manual recharging port
Cliff sensor
Front wheel
Charging electrode
Charging electrode
Right side brush
Left side brush
Cliff sensor
UV lamp
Trailing bar with mop
Cliff sensor
Lifting bracket
Roller brush
Product Anatomy and Accessories
Anatomy of the Main Unit

Unit Display Panel
Press this button and the cleaner will start automatic cleaning until the power is low, at
which point it will automatically return to the auto charging dock station. During the
course of cleaning, touch this button and the cleaner will stop.
When this button is on, the unit will automatically enter into Spot cleaning mode with a
1 square meter spiral pattern for approximately 2-3 minutes; during the cleaning
process, press any button on the remote control to stop.
Press the " " on the remote control and the cleaner will seek the docking station for
charging.
Press the TIMER " "button and Spot " " button on the remote control. The " "
icon on the display panel will light up, and the cleaner will enter into the current day/
hour/minute setting and schedule day/hour/minute setting (see page 11 for the clock
and schedule cleaning settings).
When the cleaner is on standing by, press the " " + " " button on the remote
control to turn off/turn on the UV lamp. (For details, see page 11.)
Attention: By default, UV sterilization is turned on.
An error code will display during a malfunction, for instance: E001 will be displayed as
E0:01
Displays day/hour/minute, for instance: Tuesday 08:28 A.M. will be displayed as 2 and
08:28
Days will be displayed as: 1,2,3,4,5,6,7
During auto charging, 1 1:1 1 will light up and when fully charged will display FULL
Before charging be sure to turn the power switch to ON.
Before cleaning, tidy up any small items or obstacles in the area, especially any
power cords or other clutter. When the battery is low during cleaning, the cleaner
will stop, beep five times, light up the recharging touch light, and automatically
return to the auto charging dock station.
Attention

When the cleaner is on standby, press the " " button on the remote control and the
cleaner will enter FULL GO mode. In this mode, the cleaner will automatically clean one
more time after it is fully charged.
When the cleaner is on standby, press the " " button on the remote control and the
cleaner will enter wall follow cleaning mode.
Unit Display Panel
Installing the Battery
FULL GO indicator
Garbage indicator
When the " " icon lights up, it indicates that either the dust bin is full, the suction
inlet is clogged, or the garbage sensors are covered with dust.
Wall follow cleaning indicator
Water seeping speed indicator
First install the small dustbin with the water tank (refer to page 14 to install). The
cleaner will automatically launch into the wet mopping mode. Press the " " button to
start auto cleaning & mopping and the " " will light up or blink.
When the water tank runs out of water, this icon will turn off, display error code E012;
and prompt “inject water, please”. To continue this function during cleaning, take out
the water tank and refill it. The indicators are normally on in the default mode, blinking
indicates it is in fast water seeping speed (See page 10 for more).
Attention
1. It is recommended to clean dust off of the suction inlet and dirt sensor when
emptying the dust bin.
2. When the main unit is cleaning, the path follows default settings but when it
detects any dirt, it will automatically switch to Spot cleaning.
3. To maximize the wet mopping effect, please fill the water tank to the fullest.
1. To install the battery, use a screwdriver to loosen the four screws on the half-moon shaped
bottom shell, and remove the battery cover (see Fig.1).
2. When installing the battery, connect the snap joints of the two terminals (see Fig. 2).
3. If the cleaner is left unused for a long time, recharge it once a month on a regular basis to
maintain the battery for optimal use.
4. The battery can only be replaced with a battery from the original manufacturer, otherwise it
may cause damage to the main unit.

Negative
recharging contact
Product Operations and Settings
Auto Charging Dock Station
Positive recharging contact
1. Securely mount the charging station on flat ground
and a wall near and perpendicular to the ground.
2. Avoid obstacles and uneven areas within 2m in front
of the docking station and 1m on both sides.
3. If the infrared signal emission window of the
charging station is blocked, the cleaner will be unable to find the charging station for
charging.
4. Keep the power cord clear of the charging station and do not leave the power cord on the
ground.

Product Operations and Settings
Remote Control Operations
Press" "and the cleaner will enter auto charging mode.
Press" "and the cleaner will enter the sleep/wake-up mode (in
sleep mode, press and hold this button for 10 seconds to enter the
wake-up mode).
Press" "and the cleaner will enter Turbo cleaning mode. This
mode increases cleaning power to provide a deeper clean suitable
for dirty floors.
Press" "and the cleaner will enter Wall follow cleaning mode.
Press" "and the cleaner will enter Spot cleaning mode.
Press" "and the cleaner will enter FULL GO mode.
Press" "and the cleaner will enter the cleaning schedule, UV
lamp ON/OFF, and water seeping speed (this is a combination
button, see page 11-12 for more).
Press" "and the cleaner will enter automatic cleaning mode.
Press" "and the main unit will start forward movement.
Press" "and the main unit will start backward movement.
Press" "and the main unit will start leftward movement.
Press" "and the main unit will start rightward movement.
Attention
1. Place two AAA batteries in the remote control. (As shown in Fig. 2)
2. When controlling the cleaner with the remote control, aim the
remote control at the sensor head of the cleaner, and keep it within
5m from the cleaner.

UV lamp settings:
By default the UV Lamp is on, to turn it off follow the steps below:
Water seeping speed settings:
By default, the water seeping speed is on standard; to switch to fast
water seeping speed follow the steps below:
Product Operations and Settings
1. In standby mode, press the " " button, then press the " " button to enter the UV lamp
settings (the UV lamp icon on the cleaner will flash);
2. Press the " " button to turn the UV lamp on and the screen will display "1 1:1 1";
3. Press the " " button to save the current settings and return to standby mode.
4. Press the " " button to turn the UV lamp off and the screen will display "00:00";
5. Press " " to save the current settings and exit to standby mode.
1. In standby mode, press the " " button, then press the " " button to enter the water
seeping speed settings (the water droplet icon " " on the cleaner will flash).
2. Press the " " button and the " " on the cleaner, the screen will display "1 1:1 1",
indicating the water tank is in the standard water seeping mode, suitable for wood
floors, as too much water will ruin the wooden floor. This mode is also suitable for
clean floors.
3. Press the " "button to save the current settings and return to the standby mode.
4. Press the " " button and the " " on the cleaner, the screen will display "00:00" the
water tank is in the quick water seeping mode, suitable for tile/marble or dirty floors.
5. Press the " "button to save the current settings and return to the standby mode.
6. Press " " to save the current settings and exit to standby mode.
Attention
After settings are complete, press the " " button, the cleaner will
automatically save the settings and exit to standby mode.

Product Operations and Settings
Cleaning schedule settings
2. Setting the current hour/minute:
1.
2.
Attention
After settings are complete, press the " " button, the cleaner will
automatically save the settings and exit to standby mode.
Setting the clock
1. Setting the current day:
a) In the standby mode, press the " " button, then press the " " button to set the day
of the week; press the " "," " buttons to switch from Monday-Sunday.
b) Press the " " button to select a day; press the " " button until it flashes to cancel
a day.
c) Press " " to save the current day and enter the hour/minute settings.

Product Operations and Settings
Virtual Blocker Settings
Instructions for the Virtual Blocker
1. Before use, remove the underside plate of the battery compartment of the virtual blocker,
and insert two D batteries according to the polarity indicated by the instructions into the
compartment (Fig. 3).
Attention: Incorrect battery installation will damage the virtual blocker.
2. The battery life depends on the emission direction, distance, and time of use. To make
efficient use of the battery, please select an appropriate emission direction and distance
to reduce the transmission power; and when the
virtual blocker is not in use, please turn off the power.
3. The virtual blocker can typically be placed at a
staircase or in a doorway.
4. When using the virtual blocker, ensure the virtual
blocker and the cleaner are placed on the same level
and that there is no obstruction in front of the virtual
blocker (Fig. 4).
5. During use, the emission distance of the virtual
blocker depends on the environment, the movement of
the cleaner, and battery level.
6. When installing, keep the virtual blocker 50cm or
more from the cleaner to avoid interference.
7. Do not point the infrared emission window at eyes.

Product Maintenance

Removing the Roller Brush
Product Maintenance

Installing the Roller Brush
Product Maintenance
1. As shown in Fig. 1, an enlarged view of the upper right part, fit the right end of the
assembly into the drive shaft of the cleaner and make sure the shaft of the roller brush
aligns with the drive shaft.
2. As shown in Fig. 2, an enlarged view of the upper right part, after installing the roller
brush, make sure the brush’s left semicircular flexible plastic member is horizontally put
in the slot.
3. As shown in Fig. 3, align the two snaps towards the two U-shaped recesses on the
surface of the cleaner and press them down to fit.

Product Maintenance

Product Maintenance
Installing the Trailing Bar and Mop
Installing the Water Tank

Error Codes and Troubleshooting
Attention